Home › Brake › BRAKE (FRONT) › FRONT BRAKE
RM2170E _54 Brake _057023 BRAKE (FRONT) _0278036 FRONT BRAKE A

BRAKE (FRONT)  FRONT BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

a.
C249590E02
2.302,1.115 2.656,1.115 2.656,1.115 2.323,1.146 true 2.688,1.031 2.833,1.177 0.146,0.146 10 false *a

Align the matchmarks of the disc and axle hub, and install the front disc.

Text in Illustration
*a Matchmark

NOTICE:

When replacing the disc with a new one, select the installation position where the front disc has minimal runout.



Hide 47722 2.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING

a.

Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.

Torque:
107 N*m (1089 kgf*cm, 79 ft.*lbf)


Hide 3.INSTALL FRONT DISC BRAKE BUSHING DUST BOOT

a.
C250561

Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bushing dust boots.

Text in Illustration
V100155

Lithium Soap Base Glycol Grease

HINT:

Apply more than 0.3 g (0.01 oz.) of lithium soap base glycol grease to each front disc brake bushing dust boot.



b.

Install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.


Hide 4.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN (for Upper Side)

a.
C211759

Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front disc brake cylinder slide pin.

Text in Illustration
V100155

Lithium Soap Base Glycol Grease


b.

Install the front disc brake cylinder slide pin to the front disc brake cylinder mounting.


c.

Push the front disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.


Hide 47769 5.INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSHING

a.
C211757

Apply a light layer of lithium soap base glycol grease to the contact surface of the front No. 2 disc brake cylinder slide pin (for Lower Side).

Text in Illustration
V100155

Lithium Soap Base Glycol Grease


b.

Install a new front disc brake cylinder slide bushing to the front disc brake cylinder slide pin (for Lower Side).


Hide 6.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN (for Lower Side)

a.
C211758

Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front disc brake cylinder slide pin.

Text in Illustration
V100155

Lithium Soap Base Glycol Grease


b.

Install the front disc brake cylinder slide pin to the front disc brake cylinder mounting.


c.

Push the front disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.


Hide 04947 7.INSTALL FRONT DISC BRAKE FITTING KIT

a.
C249585E03
2.135,0.958 2.292,1.115 0.156,0.156 10 false *1 1.625,0.969 1.792,1.115 0.167,0.146 10 false *2 1.667,4.208 1.823,4.365 0.156,0.156 10 false *1 2.115,4.219 2.281,4.365 0.167,0.146 10 false *2

Install the 2 front No. 1 disc brake pad support plates and 2 front No. 2 disc brake pad support plates to the front disc brake cylinder mounting.

Text in Illustration
*1 Front No. 1 Disc Brake Pad Support Plate
*2 Front No. 2 Disc Brake Pad Support Plate

NOTICE:

Be sure to install each front disc brake pad support plate in the correct position and direction.



Hide 04945 8.INSTALL FRONT ANTI-SQUEAL SHIM KIT

a.
C256881

Install the pad wear indicator plate to each front disc brake pad.

NOTICE:

Install each pad wear indicator plate in the correct position and direction.



b.
C227824E03
0.313,0.49 0.51,0.677 0.198,0.188 10 false *A 0.313,1.906 0.51,2.094 0.198,0.188 10 false *B

Apply disc brake grease to both sides of each front No. 1 anti-squeal shim as shown in the illustration.

Text in Illustration
*A Inner
*B Outer
V100145

Disc Brake Grease

NOTICE:
·

When replacing worn pads, the front anti-squeal shims must be replaced together with the pads.

·

Apply disc brake grease to the area that contacts the anti-squeal shims.




c.
C256880E02
0.406,0.646 0.406,0.292 0.406,0.292 0.906,0.292 false 0.854,0.938 0.854,0.583 0.854,0.583 1.354,0.583 false 2.479,2.469 2.479,2.823 2.479,2.823 1.979,2.823 false 3.042,2.708 3.042,3.063 3.042,3.063 2.542,3.063 false 1.375,0.49 1.531,0.635 0.156,0.146 10 false *1 0.927,0.188 1.083,0.333 0.156,0.146 10 false *2 1.813,2.74 1.969,2.885 0.156,0.146 10 false *1 2.333,2.99 2.49,3.135 0.156,0.146 10 false *2

Install the front No. 1 anti-squeal shim and front No. 2 anti-squeal shim to each front disc brake pad.

Text in Illustration
*1 Front No. 1 Anti-squeal Shim
*2 Front No. 2 Anti-squeal Shim

NOTICE:
·

Install the shims in the correct positions and directions.

·

Disc brake grease can seep out slightly from the area where the anti-squeal shim is installed.

·

Make sure that disc brake grease is not applied onto the lining surface.




Hide 04465 9.INSTALL FRONT DISC BRAKE PAD

a.
C249583

Install the 2 front disc brake pads to the front disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the disc brake pads or the front disc.



Hide 47750 10.INSTALL DISC BRAKE CYLINDER ASSEMBLY

a.
C249582E03
1.067,1.107 1.224,1.26 0.157,0.153 10 *a 1.032,0.421 1.181,0.571 0.149,0.15 10 *b

Hold the front disc brake cylinder slide pin, and install the disc brake cylinder assembly to the front disc brake cylinder mounting with the 2 bolts.

Text in Illustration
*a Hold
*b Turn

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


Hide 47313J 11.CONNECT FRONT FLEXIBLE HOSE

a.
C249580E02
1.375,0.969 2.531,0.969 true 2.552,0.875 2.708,1.021 0.156,0.146 10 false *a

Connect the front flexible hose to the disc brake cylinder assembly with a new union bolt and a new gasket.

Text in Illustration
*a Lock Hole

Torque:
30 N*m (310 kgf*cm, 22 ft.*lbf)

HINT:

Install the flexible hose lock securely into the lock hole in the disc brake cylinder.



Hide 12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the cable to the negative (-) auxiliary battery terminal (See page Power Source / Network>1NZ-FXE BATTERY / CHARGING>AUXILIARY BATTERY>INSTALLATION).


b.

Perform the following procedure if air bleeding is not necessary:

i.

Connect the reservoir level switch connector.




Hide 14.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)