The intelligent tester must be used for air bleeding. If not used, the air bleeding will be incomplete, which is hazardous and may lead to an accident.
Perform air bleeding with the shift lever in P and the parking brake applied.
As brake fluid may overflow when bleeding, do not stand the fluid can on the reservoir inlet.
Perform air bleeding while maintaining the brake fluid level between the MIN and MAX lines on the brake fluid reservoir.
Air bleeding will be difficult if the following occurs:
The brake actuator hose (the hose between the brake booster pump assembly and brake fluid reservoir) is higher than the fluid level and air enters the hose.
During the air bleeding procedure, air enters the brake booster pump while the pump motor is operating.
While performing air bleeding, the accumulator pressure drop may cause a buzzer to sound. As there is no problem, continue with the operation.
During air bleeding, DTCs for pressure sensor malfunctions, etc. may be stored. After air bleeding and if instructed in the procedures, clear the DTCs.
Release the parking brake during the linear valve offset calibration procedure.
Do not allow brake fluid to adhere to any painted surface such as the vehicle body. If brake fluid leaks onto any painted surface, immediately clean it off.
When bleeding air, select the suitable work procedure according to the table below.
| Replaced/Installed Item | Work Procedure |
|---|---|
| Flexible hose (front/rear) | Bleed brake line |
| Front disc brake cylinder assembly | |
| Rear wheel cylinder assembly | |
| Brake booster pump assembly | Bleed brake system |
| Brake booster with master cylinder assembly | |
| Brake master cylinder reservoir assembly |
1.BLEED BRAKE LINE
Separate the center No. 1 cowl top ventilator louver.
for LHD:
Disengage the 4 claws and 6 guides, and separate the center No. 1 cowl top ventilator louver.
for RHD:
Disengage the 3 claws and 5 guides, and separate the center No. 1 cowl top ventilator louver.
Bleed brake line.
Remove the brake master cylinder reservoir filler cap assembly.
| *A | for LHD | *B | for RHD |
Add brake fluid into the reservoir between the MAX and MIN lines on the brake fluid reservoir.
SAE J1703 or FMVSS No. 116 DOT3
Connect the intelligent tester to the DLC3 and turn the power switch on (IG).
Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.
Select "Usual air bleeding" on the intelligent tester display, and bleed air from the brake fluid following the instructions on the intelligent tester.
After air bleeding, tighten each bleeder plug.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the intelligent tester off and turn the power switch off.
Install the brake master cylinder reservoir filler cap.
Inspect for brake fluid leaks.
Install the center No. 1 cowl top ventilator louver.
for LHD:
Engage the 4 claws and 6 guides to install the center No. 1 cowl top ventilator louver.
for RHD:
Engage the 3 claws and 5 guides to install the center No. 1 cowl top ventilator louver.
2.BLEED BRAKE SYSTEM
Remove the outer cowl top panel sub-assembly.
for LHD: See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for LHD)>REMOVAL
for RHD: See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for RHD)>REMOVAL
Bleed the brake system.
Wait at least 2 minutes with the power switch off, and disconnect the reservoir level switch connector.
| *A | for LHD | *B | for RHD |
Do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.
This procedure is not required if the reservoir level switch connector has been disconnected.
Remove the brake master cylinder reservoir filler cap assembly.
| *A | for LHD | *B | for RHD |
Add brake fluid into the reservoir between the MAX and MIN lines on the brake fluid reservoir.
SAE J1703 or FMVSS No. 116 DOT3
Connect the intelligent tester to the DLC3 and turn the power switch on (IG).
Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.
Select "ABS actuator has been replaced" on the intelligent tester display, and bleed air from the brake fluid following the instructions on the intelligent tester.
Before following the instructions on the intelligent tester to perform linear valve offset calibration, release the parking brake. When calibration is complete, immediately apply the parking brake.
After air bleeding, tighten each bleeder plug.
The stroke simulator bleeder plug is positioned as shown in the illustration.
| *1 | Stroke Simulator Bleeder Plug |
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the intelligent tester off and turn the power switch off.
Install the brake master cylinder reservoir filler cap.
Inspect for brake fluid leaks.
Install the outer cowl top panel sub-assembly.
for LHD: See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for LHD)>INSTALLATION
for RHD: See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for RHD)>INSTALLATION