Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2170E _55 Steering _057026 POWER ASSIST SYSTEMS _0278045 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1524/24  Motor Circuit Malfunction  C1555/55  Predriver Malfunction  


DESCRIPTION

The power steering ECU assembly supplies current to the power steering motor assembly through the motor circuit.

DTC No. DTC Detection Condition Trouble Area
C1524/24 Short (or open) in motor circuit or abnormal voltage in motor circuit
·

Power steering motor assembly

·

Power steering ECU assembly


C1555/55 Predriver (Motor relay circuit) malfunction

WIRING DIAGRAM

C250218E26
4.625,3.26 7.031,3.542 2.406,0.281 10 false Power Steering ECU Assembly 0.677,3.177 2.833,3.521 2.156,0.344 10 false Power Steering Motor Assembly 4.885,1 5.302,1.26 0.417,0.26 10 false M1 4.885,2.188 5.25,2.479 0.365,0.292 10 false M2 4.667,0.885 4.906,1.146 0.24,0.26 10 false 1 4.667,2.083 4.938,2.344 0.271,0.26 10 false 2 4.625,3.104 5.052,3.313 0.427,0.208 10 false z8

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced with a new one, perform assist map writing and torque sensor zero point calibration (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK POWER STEERING ECU ASSEMBLY
a.

Turn the power switch on (ready).


U183536E01
1.608,0.701 1.776,0.863 0.168,0.163 10 z8 1.477,1.942 1.165,2.712 false 1.855,1.95 2.139,2.706 false 1.07,2.757 1.346,2.920 0.276,0.163 10 M2 2.067,2.757 2.315,2.920 0.248,0.163 10 M1 0.15,0.11 0.426,0.273 0.276,0.163 10 *a

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition
(Steering Wheel Position)
Specified Condition
z8-1 (M1) - Body ground Power switch on (ready)
(Turned to right)
6 to 8 V
z8-1 (M1) - Body ground Power switch on (ready)
(Turned to left)
9 to 16 V
z8-2 (M2) - Body ground Power switch on (ready)
(Turned to right)
9 to 16 V
z8-2 (M2) - Body ground Power switch on (ready)
(Turned to left)
6 to 8 V


Text in Illustration
*a Component with harness connected
(Power Steering ECU Assembly)



OK

2.CHECK POWER STEERING MOTOR ASSEMBLY

NG

REPLACE POWER STEERING ECU ASSEMBLY

2.CHECK POWER STEERING MOTOR ASSEMBLY
a.

Disconnect the connector from the power steering ECU assembly.


U183577E01
1.642,0.187 1.811,0.343 0.168,0.156 10 z8 2.278,1.855 2.488,2.010 0.210,0.156 10 M2 2.352,1.844 2.071,1.359 false 0.92,1.855 1.130,2.010 0.210,0.156 10 M1 1.085,1.844 1.365,1.359 false 0.18,0.156 0.335,0.312 0.154,0.156 10 *a

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z8-1 (M1) - z8-2 (M2) Always 0.08 to 0.15 Ω
z8-1 (M1) - Body ground Always 1 MΩ or higher
z8-2 (M2) - Body ground Always 1 MΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE POWER STEERING MOTOR ASSEMBLY