Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2011.12–2018.08
RM2170E _55 Steering _057026 POWER ASSIST SYSTEMS _0278045 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  DTC CHECK / CLEAR  


CHECK DTC (USING THE INTELLIGENT TESTER)


a.

Turn the power switch off (lock).


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the intelligent tester on.


e.

Read the DTCs following the display on the intelligent tester. Enter the following menus: Chassis / EMPS / DTC.


f.

Refer to the Diagnostic Trouble Code Chart for DTC information (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).



CHECK DTC (USING SST CHECK WIRE)


a.
C248264E50
1.487,0.223 1.72,0.369 0.233,0.146 10 CG 1.62,0.812 1.62,0.405 false 1.749,1.877 1.963,2.023 0.215,0.146 10 TC 0.176,0.037 0.332,0.219 0.156,0.182 10 *1 1.86,1.851 1.86,1.483 false

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

Text in Illustration
*1 DLC3


b.

Turn the power switch on (IG).


c.
F102422E02
1.094,3.333 0.99,3.083 false 1.469,3.333 1.438,3.104 false 1.938,3.333 2.01,2.885 false 2.26,3.333 2.281,3.156 false 1.188,3.344 1.208,2.875 false 0.188,0.229 0.5,0.427 0.313,0.198 10 false *1 0.542,1.219 0.854,1.417 0.313,0.198 10 false *a 0.563,1.719 0.875,1.917 0.313,0.198 10 false *b 0.177,2.448 0.49,2.646 0.313,0.198 10 false *2 0.188,3.292 0.5,3.49 0.313,0.198 10 false *a 0.208,3.75 0.521,3.948 0.313,0.198 10 false *b 1.24,3.979 1.552,4.177 0.313,0.198 10 false *d 2.51,3.969 2.823,4.167 0.313,0.198 10 false *e 0.844,3.375 1.156,3.573 0.313,0.198 10 false 4 0.896,2.927 1.208,3.125 0.313,0.198 10 false 0.5 1.073,2.677 1.385,2.875 0.313,0.198 10 false 0.5 1.365,2.927 1.677,3.125 0.313,0.198 10 false 1.5 1.917,2.677 2.229,2.875 0.313,0.198 10 false 2.5 2.198,2.958 2.51,3.156 0.313,0.198 10 false 0.5 1.135,0.813 1.448,1.01 0.313,0.198 10 false 0.25 2.229,0.563 2.542,0.76 0.313,0.198 10 false 0.25 2.667,4.25 2.979,4.448 0.313,0.198 10 false (*c) 2.646,1.969 2.958,2.167 0.313,0.198 10 false (*c)

Read and write down any DTCs indicated by the EPS warning light on the combination meter assembly. Refer to the chart on the left for examples of a normal code and DTCs 21 and 22.

HINT:
·

If the EPS warning light does not blink to display any DTCs set or the normal code, inspect the circuit shown in the table below.

Trouble Area See Page
EPS warning light circuit (Click here)

·

If two or more malfunctions are detected simultaneously, DTCs will be displayed in ascending numerical order.




d.

Refer to the Diagnostic Trouble Code Chart for DTC information (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).

Text in Illustration
*1 Normal code
*2 Codes 21 and 22
*a ON
*b OFF
*c Seconds
*d Code 21
*e Code 22



CLEAR DTC (USING THE INTELLIGENT TESTER)


a.

Turn the power switch off (lock).


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the intelligent tester on.


e.

Clear the DTCs following the display on the intelligent tester. Enter the following menus: Chassis / EMPS / DTC / Clear.


f.

According to the display on the intelligent tester, select the trouble code data display with the clear button.


g.

Turn the power switch off (lock).


h.

Disconnect the intelligent tester from the DLC3.



CLEAR DTC (USING SST CHECK WIRE)


a.
C248264E34
1.492,0.223 1.724,0.369 0.233,0.146 10 CG 1.625,0.812 1.625,0.405 false 1.32,1.873 1.516,2.019 0.196,0.146 10 TS 1.637,1.506 1.441,1.822 false 1.96,1.877 2.174,2.023 0.215,0.146 10 TC 1.89,1.501 2.055,1.835 false 0.181,0.037 0.337,0.219 0.156,0.182 10 *1

Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3, and also terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


b.

Turn the power switch on (IG).


c.

Disconnect and reconnect terminal 13 (TC) of the DLC3 4 times or more within 8 seconds.


d.

Check that the EPS warning light blinks a code to indicate normality.


e.

Turn the power switch off (lock).


f.

Remove SST from the DLC3.



Text in Illustration
*1 DLC3