Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM2170E _56 Audio / Visual / Telematics _057029 AUDIO / VIDEO _0278060 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Speaker Circuit  


DESCRIPTION

The sound signals amplified by the radio receiver assembly are sent to the speakers from the radio receiver assembly via the speaker circuit.

If there is a short in a speaker circuit, the radio receiver assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly or speakers.

WIRING DIAGRAM

E238696E19
0.458,1.281 1.76,1.646 1.302,0.365 10 false Front No. 1 Speaker Assembly LH 0.479,3.208 1.781,3.573 1.302,0.365 10 false Front No. 1 Speaker Assembly RH 3,1.188 4.313,1.604 1.313,0.417 10 false Front No. 2 Speaker Assembly LH 3.01,3.188 4.354,3.552 1.344,0.365 10 false Front No. 2 Speaker Assembly RH 0.813,5.042 1.74,5.354 0.927,0.313 10 false Rear Speaker Assembly LH 0.802,6.542 1.74,6.938 0.938,0.396 10 false Rear Speaker Assembly RH 1.823,1.073 2,1.229 0.177,0.156 10 false 1 2.333,0.833 2.51,0.99 0.177,0.156 10 false 4 1.823,3.052 2,3.208 0.177,0.156 10 false 1 2.323,2.802 2.5,2.958 0.177,0.156 10 false 4 5.552,2.729 5.729,2.885 0.177,0.156 10 false 1 1.844,4.865 2.021,5.021 0.177,0.156 10 false 1 1.813,6.385 1.99,6.542 0.177,0.156 10 false 1 5.552,6.146 5.729,6.302 0.177,0.156 10 false 1 1.823,1.667 2,1.823 0.177,0.156 10 false 2 1.844,3.615 2.021,3.771 0.177,0.156 10 false 2 1.854,5.417 2.031,5.573 0.177,0.156 10 false 2 1.823,6.948 2,7.104 0.177,0.156 10 false 2 5.563,4.646 5.74,4.802 0.177,0.156 10 false 2 4.563,0.813 4.74,0.969 0.177,0.156 10 false 3 4.552,2.802 4.729,2.958 0.177,0.156 10 false 3 5.573,0.698 5.75,0.854 0.177,0.156 10 false 2 5.563,6.771 5.74,6.927 0.177,0.156 10 false 3 2.323,1.719 2.5,1.875 0.177,0.156 10 false 2 2.323,3.698 2.5,3.854 0.177,0.156 10 false 2 4.563,1.74 4.792,1.875 0.229,0.135 10 false 1 4.552,3.677 4.781,3.813 0.229,0.135 10 false 1 4.052,2.802 4.521,2.99 0.469,0.188 10 false TWR+ 4.052,3.885 4.521,4.073 0.469,0.188 10 false TWR- 2.469,2.813 2.833,2.969 0.365,0.156 10 false + 2.479,3.833 2.844,3.99 0.365,0.156 10 false - 2.49,0.844 2.854,1.021 0.365,0.177 10 false + 2.479,1.917 2.74,2.073 0.26,0.156 10 false - 4.104,0.813 4.563,0.99 0.458,0.177 10 false TWL+ 4.104,1.917 4.531,2.135 0.427,0.219 10 false TWL- 5.542,3.583 5.698,3.76 0.156,0.177 10 false 5 5.573,1.625 5.708,1.802 0.135,0.177 10 false 6 5.573,5.271 5.698,5.417 0.125,0.146 10 false 6 5.833,0.938 6.198,1.115 0.365,0.177 10 false FL+ 5.833,1.823 6.094,1.979 0.26,0.156 10 false FL- 5.833,2.927 6.198,3.083 0.365,0.156 10 false FR+ 5.833,3.802 6.198,3.958 0.365,0.156 10 false FR- 5.833,4.844 6.167,5.042 0.333,0.198 10 false RL+ 5.833,5.479 6.115,5.698 0.281,0.219 10 false RL- 5.833,6.354 6.229,6.604 0.396,0.25 10 false RR+ 5.833,6.99 6.292,7.271 0.458,0.281 10 false RR- 5.469,0.958 5.844,1.135 0.375,0.177 10 false G37 5.469,1.813 5.844,1.99 0.375,0.177 10 false G37 5.469,2.927 5.844,3.104 0.375,0.177 10 false G37 5.458,3.792 5.833,3.969 0.375,0.177 10 false G37 5.458,4.844 5.771,5 0.313,0.156 10 false G38 5.458,5.479 5.771,5.635 0.313,0.156 10 false G38 5.458,6.365 5.771,6.521 0.313,0.156 10 false G38 5.458,6.99 5.771,7.146 0.313,0.156 10 false G38 0.458,1.125 0.688,1.281 0.229,0.156 10 false J8 0.479,3.042 0.708,3.198 0.229,0.156 10 false H8 0.813,4.875 1.104,5.021 0.292,0.146 10 false L4 0.802,6.354 1.094,6.5 0.292,0.146 10 false K4 3,1.031 3.313,1.229 0.313,0.198 10 false J9 3.01,3.021 3.333,3.198 0.323,0.177 10 false H9 5.781,7.448 6.792,7.802 1.01,0.354 10 false Radio Receiver Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR
a.

Disconnect the connectors from the radio receiver assembly and speakers.


b.

Measure the resistance between each of the front No. 2 speaker assemblies and the radio receiver assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-1 (FR+) - H9-3 (TWR+) Always Below 1 Ω
G37-5 (FR-) - H9-1 (TWR-) Always Below 1 Ω
G37-2 (FL+) - J9-3 (TWL+) Always Below 1 Ω
G37-6 (FL-) - J9-1 (TWL-) Always Below 1 Ω



c.

Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
J9-4 (+) - J8-1 Always Below 1 Ω
J9-2 (-) - J8-2 Always Below 1 Ω
H9-4 (+) - H8-1 Always Below 1 Ω
H9-2 (-) - H8-2 Always Below 1 Ω



d.

Measure the resistance between each of the rear speaker assemblies and the radio receiver assembly to check for an open circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
G38-1 (RR+) - K4-1 Always Below 1 Ω
G38-3 (RR-) - K4-2 Always Below 1 Ω
G38-2 (RL+) - L4-1 Always Below 1 Ω
G38-6 (RL-) - L4-2 Always Below 1 Ω



e.

Measure the resistance between the radio receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-1 (FR+) - Body ground Always 10 kΩ or higher
G37-5 (FR-) - Body ground Always 10 kΩ or higher
G37-2 (FL+) - Body ground Always 10 kΩ or higher
G37-6 (FL-) - Body ground Always 10 kΩ or higher
G38-1 (RR+) - Body ground Always 10 kΩ or higher
G38-3 (RR-) - Body ground Always 10 kΩ or higher
G38-2 (RL+) - Body ground Always 10 kΩ or higher
G38-6 (RL-) - Body ground Always 10 kΩ or higher



f.

Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
J9-4 (+) - Body ground Always 10 kΩ or higher
J9-2 (-) - Body ground Always 10 kΩ or higher
H9-4 (+) - Body ground Always 10 kΩ or higher
H9-2 (-) - Body ground Always 10 kΩ or higher




OK

2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.
U183674E02
0.542,2.031 0.833,2.198 0.292,0.167 10 false J8 0.531,1.677 0.823,1.844 0.292,0.167 10 false H8 0.094,0.073 0.271,0.24 0.177,0.167 10 false *a 0.958,1.667 1.135,1.833 0.177,0.167 10 false *A 0.958,2.052 1.135,2.219 0.177,0.167 10 false *B

Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J8-1 - J8-2 Always 3.2 to 4.8 Ω
H8-1 - H8-2 Always 3.2 to 4.8 Ω


Text in Illustration
*A for RH
*B for LH
*a Component without harness connected
(Front No. 1 Speaker Assembly)




OK

3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.
U183682E01
0.094,0.053 0.248,0.200 0.154,0.147 10 *a 1.641,0.696 1.878,0.859 0.237,0.163 10 H9 1.646,1.04 1.849,1.203 0.202,0.163 10 J9 0.744,2.633 0.878,2.801 0.134,0.168 10 + 1.214,2.23 1.639,2.377 0.425,0.147 10 TWR+ 2.086,2.633 2.199,2.780 0.112,0.147 10 - 2.326,2.23 2.751,2.377 0.425,0.147 10 TWR- 1.4,1.773 0.873,2.647 false 1.682,1.791 1.613,2.192 false 2.25,1.778 2.583,2.192 false 1.99,1.773 2.102,2.647 false 2.326,2.428 2.730,2.575 0.404,0.147 10 TWL- 1.214,2.428 1.618,2.575 0.404,0.147 10 TWL+ 2.045,0.696 2.252,0.844 0.206,0.147 10 *A 1.716,2.23 1.922,2.377 0.206,0.147 10 *A 1.703,2.428 1.909,2.575 0.206,0.147 10 *B 2.045,1.029 2.252,1.177 0.206,0.147 10 *B 2.816,2.23 3.022,2.377 0.206,0.147 10 *A 2.82,2.428 3.026,2.575 0.206,0.147 10 *B

Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J9-3 (TWL+) - J9-1 (TWL-) Always 10 kΩ or higher
J9-4 (+) - J9-3 (TWL+) Always Below 1 Ω
J9-2 (-) - J9-1 (TWL-) Always Below 1 Ω
H9-3 (TWR+) - H9-1 (TWR-) Always 10 kΩ or higher
H9-4 (+) - H9-3 (TWR+) Always Below 1 Ω
H9-2 (-) - H9-1 (TWR-) Always Below 1 Ω


Text in Illustration
*A for RH
*B for LH
*a Component without harness connected
(Front No. 2 Speaker Assembly)




OK

4.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

4.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
a.

Check that the malfunction disappears when a known good speaker is installed (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL).

OK:

Malfunction disappears.


HINT:
·

Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

·

When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.

·

Perform the above inspection on both LH and RH sides.





OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE)

NG

5.INSPECT REAR SPEAKER ASSEMBLY
5.INSPECT REAR SPEAKER ASSEMBLY
a.
U183675E02
0.667,2.052 0.958,2.219 0.292,0.167 10 false L4 0.656,1.667 0.948,1.833 0.292,0.167 10 false K4 0.104,0.104 0.281,0.271 0.177,0.167 10 false *a 1.052,1.667 1.229,1.833 0.177,0.167 10 false *A 1.052,2.063 1.229,2.229 0.177,0.167 10 false *B

Resistance check

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L4-1 - L4-2 Always 3.2 to 4.8 Ω
K4-1 - K4-2 Always 3.2 to 4.8 Ω


Text in Illustration
*A for RH
*B for LH
*a Component without harness connected
(Rear Speaker Assembly)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG