The hybrid vehicle control computer assembly communicates with the ECM and brake booster with master cylinder assembly (skid control ECU). When the hybrid vehicle control computer assembly does not receive data from the ECM or brake booster with master cylinder assembly (skid control ECU), the hybrid vehicle control computer assembly stores DTC U0100 or U0129.
The ECM communicates with the hybrid vehicle control computer assembly. When the ECM does not receive data from the hybrid vehicle control computer assembly, the ECM stores DTC U0293.
The brake booster with master cylinder assembly (skid control ECU) communicates with the hybrid vehicle control computer assembly. When the brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control computer assembly, the brake booster with master cylinder assembly (skid control ECU) stores DTC U0293.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| U0100 | The hybrid vehicle control computer assembly does not receive data from the ECM. | ·
Open or short in sub bus 15 main line or connector ·
Open or short in sub bus 15 branch line or connector ·
Power source circuit of hybrid vehicle control computer assembly ·
Hybrid vehicle control computer assembly ·
Power source circuit of ECM ·
ECM ·
Open or short in CAN junction connector LH |
| U0129 | The hybrid vehicle control computer assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU). | ·
Open or short in sub bus 15 main line or connector ·
Open or short in sub bus 15 branch line or connector ·
Power source circuit of hybrid vehicle control computer assembly ·
Hybrid vehicle control computer assembly ·
Power source circuit of brake booster with master cylinder assembly (skid control ECU) ·
Brake booster with master cylinder assembly (Skid control ECU) ·
Open or short in CAN junction connector LH |
| U0293 | ·
The ECM does not receive data from the hybrid vehicle control computer assembly. ·
The brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control computer assembly. |
·
Open or short in sub bus 15 main line or connector ·
Open or short in sub bus 15 branch line or connector ·
Power source circuit of ECM ·
ECM ·
Power source circuit of hybrid vehicle control computer assembly ·
Hybrid vehicle control computer assembly ·
Power source circuit of brake booster with master cylinder assembly (skid control ECU) ·
Brake booster with master cylinder assembly (Skid control ECU) ·
Open or short in CAN junction connector LH |
This diagnosis procedure is for when DTC U0100, U0129 and U0293 are output at the same time.
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Reconfirm DTCs.
If the hybrid vehicle control computer assembly outputs only DTC U0129, troubleshoot DTC U0129 and check the branch circuit of sub bus 15.
| Result | Proceed to |
|---|---|
| The hybrid vehicle control computer assembly outputs DTC U0129 and other DTCs.
(GTS display: Hybrid Control) |
A |
| The hybrid vehicle control computer assembly outputs only DTC U0129.
(GTS display: Hybrid Control) |
B |
A
B
Disconnect the cable from the negative (-) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| G81-31 (CA3P) - G81-30 (CA3N) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or higher: Open circuit in main bus lines | |||
| G81-31 (CA3P) - G80-6 (E1) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| G81-30 (CA3N) - G80-6 (E1) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| G81-31 (CA3P) - G81-3 (BATT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| G81-30 (CA3N) - G81-3 (BATT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| *a | Component with harness connected
(Hybrid Vehicle Control Computer Assembly) |
When the values are as specified, clear and recheck for DTCs. When no DTCs are output, check for malfunctions such as damage or improper connection of the relevant connectors.
If DTCs are output although the bus circuit is normal and DTCs were cleared, replace the hybrid vehicle control computer assembly.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Open circuit in CAN main bus lines) | B |
| NG (Short circuit between bus lines) | C |
·
NG (Ground short) ·
NG (+B short) |
D |
A
B
C
D
Disconnect the G81 hybrid vehicle control computer assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G81-31 (CA3P) - G81-30 (CA3N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control Computer Assembly) |
OK
NG
Reconnect the G81 hybrid vehicle control computer assembly connector.
Disconnect the G86 CAN junction connector LH (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G86-10 (CANH) - G86-21 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Hybrid vehicle control computer assembly |
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side)) |
| *b | to Hybrid Vehicle Control Computer Assembly |
OK
NG
Reconnect the G86 CAN junction connector LH (instrument panel wire side).
Disconnect the A74 CAN junction connector LH (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A74-3 (CANH) - A74-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | ECM |
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side)) |
| *b | to ECM |
OK
NG
Reconnect the A74 CAN junction connector LH (engine room main wire side).
Disconnect the A40 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-12 (CANP) - A40-25 (CANN) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Disconnect the G81 hybrid vehicle control computer assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G81-31 (CA3P) - G81-30 (CA3N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control Computer Assembly) |
OK
NG
Reconnect the G81 hybrid vehicle control computer assembly connector.
Disconnect the G86 CAN junction connector LH (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G86-10 (CANH) - G86-21 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Hybrid vehicle control computer assembly |
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side)) |
| *b | to Hybrid Vehicle Control Computer Assembly |
OK
NG
Reconnect the G86 CAN junction connector LH (instrument panel wire side).
Disconnect the A74 CAN junction connector LH (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A74-1 (CANH) - A74-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Brake booster with master cylinder assembly (Skid control ECU) |
| A74-3 (CANH) - A74-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | ECM |
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side)) |
| *b | to Brake Booster with Master Cylinder Assembly (Skid Control ECU) |
| *c | to ECM |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (ECM CAN main bus lines) | B |
| NG (Brake booster with master cylinder assembly (Skid control ECU) CAN branch lines) | C |
A
B
C
Reconnect the A74 CAN junction connector LH (engine room main wire side).
Disconnect the A40 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-12 (CANP) - A40-25 (CANN) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Reconnect the A74 CAN junction connector LH (engine room main wire side).
Disconnect the A41 brake booster with master cylinder assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-35 (CA2H) - A41-34 (CA2L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| *a | Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU)) |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the G86 CAN junction connector LH (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G86-10 (CANH) - G4-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Hybrid vehicle control computer assembly |
| G86-21 (CANL) - G4-4 (CG) | |||
| G86-10 (CANH) - G4-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Hybrid vehicle control computer assembly |
| G86-21 (CANL) - G4-16 (BAT) |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side)) |
| *b | to Hybrid Vehicle Control Computer Assembly |
OK
NG
Disconnect the A74 CAN junction connector LH (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A74-1 (CANH) - G4-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Brake booster with master cylinder assembly (Skid control ECU) |
| A74-12 (CANL) - G4-4 (CG) | |||
| A74-3 (CANH) - G4-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | ECM |
| A74-14 (CANL) - G4-4 (CG) | |||
| A74-1 (CANH) - G4-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Brake booster with master cylinder assembly (Skid control ECU) |
| A74-12 (CANL) - G4-16 (BAT) | |||
| A74-3 (CANH) - G4-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | ECM |
| A74-14 (CANL) - G4-16 (BAT) |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side)) |
| *b | to Brake Booster with Master Cylinder Assembly (Skid Control ECU) |
| *c | to ECM |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (ECM CAN main bus line) | B |
| NG (Brake booster with master cylinder assembly (Skid control ECU) CAN branch line) | C |
A
B
C
Disconnect the G80 and G81 hybrid vehicle control computer assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G81-31 (CA3P) - G80-6 (E1) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G81-30 (CA3N) - G80-6 (E1) | ||
| G81-31 (CA3P) - G81-3 (BATT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G81-30 (CA3N) - G81-3 (BATT) |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control Computer Assembly) |
OK
NG
Disconnect the A40 and C9 or C10 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-12 (CANP) - C9-16 (E1)*1
A40-12 (CANP) - C10-16 (E1)*2 |
Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A40-25 (CANN) - C9-16 (E1)*1
A40-25 (CANN) - C10-16 (E1)*2 |
||
| A40-12 (CANP) - A40-1 (BATT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A40-25 (CANN) - A40-1 (BATT) |
*1: for RHD
*2: for LHD
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.
| *A | for RHD |
| *B | for LHD |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Disconnect the A41 brake booster with master cylinder assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-35 (CA2H) - A41-28 (GND) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A41-34 (CA2L) - A41-28 (GND) | ||
| A41-35 (CA2H) - A41-14 (BI) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A41-34 (CA2L) - A41-14 (BI) |
It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.
Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.
| *a | Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU)) |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C