Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.11
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0129  Lost Communication with Brake System Control Module  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
U0129 No communication from the brake booster with master cylinder assembly (skid control ECU) continues.
·

Brake booster with master cylinder assembly (Skid control ECU) branch line or connector

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (Skid control ECU) ground circuit

·

Brake booster with master cylinder assembly (Skid control ECU)



HINT:

This diagnosis procedure is for when DTC U0129 is output only by the hybrid vehicle control computer assembly (GTS display: Hybrid Control).


WIRING DIAGRAM

C244195E39
1.146,5.01 3.063,5.219 1.917,0.208 10 false : CAN Main Bus Line (CANH) 2.677,0.771 4.469,0.948 1.792,0.177 10 false CAN Junction Connector LH 0.417,2.844 1.813,3.219 1.396,0.375 10 false Hybrid Vehicle Control Computer Assembly 0.667,2.271 1.115,2.479 0.448,0.208 10 false 120 Ω 6.188,2.271 6.635,2.479 0.448,0.208 10 false 120 Ω 6.188,2.833 6.635,3.042 0.448,0.208 10 false ECM 5.292,3.823 6.156,4.031 0.865,0.208 10 false Trouble Area 3.302,3.052 3.51,3.26 0.208,0.208 10 false 35 3.208,3.292 3.625,3.458 0.417,0.167 10 false CA2H 2.677,4.083 4.896,4.448 2.219,0.365 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 2.052,3.708 2.969,4.063 0.917,0.354 10 false ABS NO. 2 3.021,3.583 3.26,3.792 0.24,0.208 10 false BI 2.375,4.094 2.656,4.26 0.281,0.167 10 false A41 3.792,3.292 4.208,3.458 0.417,0.167 10 false CA2L 4.073,3.563 4.427,3.729 0.354,0.167 10 false GND 3.927,3.052 4.135,3.26 0.208,0.208 10 false 34 4.438,3.448 4.646,3.656 0.208,0.208 10 false 28 2.792,3.448 2.969,3.604 0.177,0.156 10 false 14 1.146,5.427 3.063,5.635 1.917,0.208 10 false : CAN Main Bus Line (CANL) 4.281,4.99 6.198,5.198 1.917,0.208 10 false : CAN Branch Line (CANH) 4.281,5.396 6.198,5.604 1.917,0.208 10 false : CAN Branch Line (CANL) 0.052,0.073 1.365,0.49 1.313,0.417 12 false Sub Bus 15:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.


OK:

DTC C1241 is not output.



OK

2.RECONFIRM DTC OUTPUT

NG

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.


HINT:

If the hybrid vehicle control computer assembly outputs DTC U0100 and DTC U0129, check the branch circuit of sub bus 15.


Result:
Result Proceed to
The hybrid vehicle control computer assembly outputs only DTC U0129.
(GTS display: Hybrid Control)
A
The hybrid vehicle control computer assembly outputs DTC U0100 and U0129.
(GTS display: Hybrid Control)
B



A

3.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

3.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159482E01
0.196,0.187 0.380,0.345 0.184,0.158 10 *a 1.566,0.857 1.854,1.015 0.288,0.158 10 A41 1.662,2.145 1.067,2.778 false 0.809,2.791 1.221,2.948 0.413,0.158 10 CA2L 1.328,2.791 1.741,2.948 0.413,0.158 10 CA2H 1.759,2.145 1.562,2.774 false

Disconnect the A41 brake booster with master cylinder assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-35 (CA2H) - A41-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (for LHD)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (for RHD)

C

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)