Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.12–2014.12
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in CAN Main Bus Line (RHD Models)  


DESCRIPTION

There may be an open circuit in one of the V bus main lines and/or a DLC3 branch line when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher.
·

DLC3 branch line or connector

·

CAN main bus line or connector

·

ECM

·

Combination meter assembly

·

CAN junction connector LH

·

CAN junction connector RH



This malfunction is not related to the lines of a CAN main bus branch or to ECUs or sensors connected a CAN main bus branch.

WIRING DIAGRAM

C251629E10
4.75,7.135 5.146,7.344 0.396,0.208 10 false ECM 4.438,7.146 4.833,7.354 0.396,0.208 10 false A40 0.823,7.99 2.719,8.219 1.896,0.229 10 false : CAN Main Bus Line (CANH) 0.823,8.417 2.719,8.646 1.896,0.229 10 false : CAN Main Bus Line (CANL) 4.156,7.99 5.875,8.219 1.719,0.229 10 false : CAN Branch Line (CANH) 4.156,8.406 5.875,8.635 1.719,0.229 10 false : CAN Branch Line (CANL) 3.823,0.958 4.229,1.135 0.406,0.177 10 false CANH 2.49,0.969 2.875,1.146 0.385,0.177 10 false CANL 2.49,6.865 2.896,7.042 0.406,0.177 10 false CANL 5.375,2.302 5.781,2.479 0.406,0.177 10 false CANH 3.802,6.875 4.24,7.052 0.438,0.177 10 false CANH 5.5,2.573 5.885,2.75 0.385,0.177 10 false CANL 5.896,2.938 6.271,3.115 0.375,0.177 10 false DLC3 5.656,2.938 5.979,3.115 0.323,0.177 10 false G4 0.49,4.635 2.438,4.833 1.948,0.198 10 false CAN Junction Connector LH 3.854,1.26 4.167,1.49 0.313,0.229 10 false 31 4.281,2.156 4.563,2.396 0.281,0.24 10 false 11 4.281,2.823 4.542,3.063 0.26,0.24 10 false 22 5.229,2.74 5.396,2.917 0.167,0.177 10 false 14 2.719,3.219 3.052,3.479 0.333,0.26 10 false 21 3.802,3.219 4.115,3.458 0.313,0.24 10 false 10 3.885,1.792 4.042,1.969 0.156,0.177 10 false 7 2.688,1.813 2.948,1.99 0.26,0.177 10 false 18 2.708,6.625 2.927,6.802 0.219,0.177 10 false 26 3.813,6.625 4.052,6.802 0.24,0.177 10 false 13 3.146,7.427 3.542,7.604 0.396,0.177 10 false 120 Ω 3.167,0.438 3.969,0.75 0.802,0.313 10 false 120 Ω 5.135,2.188 5.292,2.365 0.156,0.177 10 false 6 2.698,1.521 2.906,1.729 0.208,0.208 10 false W 3.844,1.521 4.063,1.729 0.219,0.208 10 false G 2.667,3.552 2.823,3.729 0.156,0.177 10 false W 4.656,2.125 4.927,2.302 0.271,0.177 10 false GR 3.906,3.552 4.438,3.906 0.531,0.354 10 false SB 4.688,2.823 4.844,3 0.156,0.177 10 false W 4.979,0.385 6.208,0.646 1.229,0.26 10 false x: Suspected Area 2.688,1.26 2.979,1.531 0.292,0.271 10 false 32 0.406,0.781 2.281,0.979 1.875,0.198 10 false Combination Meter Assembly 0.167,0.156 2.042,0.354 1.875,0.198 12 false V Bus: 0.125,0.781 0.469,0.958 0.344,0.177 10 false G1 3.865,6.021 4.021,6.198 0.156,0.177 10 false L 2.708,6.042 2.865,6.219 0.156,0.177 10 false W 0.49,2.542 2.438,2.74 1.948,0.198 10 false CAN Junction Connector RH 2.844,3.938 3.135,4.115 0.292,0.177 10 false G71 0.146,2.542 0.531,2.833 0.385,0.292 10 false G72 3.594,3.927 3.885,4.104 0.292,0.177 10 false G71 2.573,3.917 2.906,4.177 0.333,0.26 10 false 15 3.979,3.927 4.292,4.167 0.313,0.24 10 false 4 2.854,5.271 3.146,5.448 0.292,0.177 10 false A51 3.604,5.281 3.896,5.458 0.292,0.177 10 false A51 2.573,5.292 2.906,5.552 0.333,0.26 10 false 20 3.969,5.281 4.281,5.521 0.313,0.24 10 false 9

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (DLC3 BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159345E02
2.063,1.885 2.438,1.271 false 2.083,2.531 2.417,2.865 false 0.083,0.031 0.927,0.365 0.844,0.333 10 false *1 1.625,0.813 1.938,0.99 0.313,0.177 10 false G4 2.448,1.063 2.854,1.24 0.406,0.177 10 false CANH 2.438,2.906 2.823,3.083 0.385,0.177 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-6 (CANH) - G4-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*1 DLC3

NOTICE:

When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).




OK

2.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - CAN J/C RH)

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - CAN J/C RH)
a.
U159531E02
1.792,2.635 1.792,2.969 1.792,2.969 1.51,2.969 false 1.906,2.635 1.906,2.969 1.906,2.969 2.188,2.969 false 0.198,0.177 0.906,0.573 0.708,0.396 10 false *a 1.083,2.896 1.563,3.104 0.479,0.208 10 false CANH 2.271,2.885 2.719,3.083 0.448,0.198 10 false CANL 1.646,0.667 1.906,0.875 0.26,0.208 10 false G1

Disconnect the G1 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-31 (CANH) - G1-32 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

3.CHECK FOR OPEN IN CAN BUS LINES (ECM - CAN J/C LH)
3.CHECK FOR OPEN IN CAN BUS LINES (ECM - CAN J/C LH)
a.

Reconnect the G1 combination meter assembly connector.


b.
U159410E02
2.573,1.615 2.854,1.615 2.854,1.615 2.854,2.396 false 2.573,1.542 2.573,0.948 2.573,0.948 2.729,0.948 false 0.146,0.083 0.385,0.323 0.24,0.24 10 false *a 2.802,0.875 3.24,1.073 0.438,0.198 10 false CANH 2.688,2.438 3.156,2.635 0.469,0.198 10 false CANL 1.771,0.719 2.052,0.896 0.281,0.177 10 false A40

Disconnect the A40 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-13 (CANH) -A40-26 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

4.CHECK FOR OPEN IN CAN BUS LINES (CAN J/C RH)
4.CHECK FOR OPEN IN CAN BUS LINES (CAN J/C RH)
a.

Reconnect the A40 ECM connector.


b.
U159396E05
2.198,1.365 2.198,0.521 2.198,0.521 2.417,0.521 false 2.188,1.563 2.188,1.938 2.188,1.938 2.406,1.938 false 1.844,1.354 1.844,0.51 1.844,0.51 1.115,0.51 false 1.854,1.563 1.854,1.938 1.854,1.938 1.125,1.938 false 0.188,0.104 0.802,0.51 0.615,0.406 10 false *a 0.552,1.229 0.979,1.5 0.427,0.271 10 false G72 0.552,0.448 1.135,0.677 0.583,0.229 10 false CANH*b 0.583,1.854 1.156,2.073 0.573,0.219 10 false CANL*b 2.5,0.438 3.083,0.667 0.583,0.229 10 false CANH*c 2.438,1.854 3.01,2.073 0.573,0.219 10 false CANL*c

Disconnect the G72 CAN junction connector RH.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G72-7 (CANH) - G72-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Combination meter assembly
G72-10 (CANH) - G72-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN junction connector LH


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector RH)
*b to Combination Meter Assembly
*c to CAN Junction Connector LH

Result:
Result Proceed to
OK A
NG (Combination meter assembly main line) B
NG (CAN junction connector LH main line) C




A

REPLACE CAN JUNCTION CONNECTOR RH

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN J/C RH - COMBINATION METER ASSEMBLY)

C

5.CHECK FOR OPEN IN CAN BUS LINES (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE))
5.CHECK FOR OPEN IN CAN BUS LINES (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE))
a.

Reconnect the G72 CAN junction connector RH.


b.
U159397E03
1.51,1.375 1.51,0.531 1.51,0.531 1.125,0.531 false 1.51,1.573 1.51,1.948 1.51,1.948 1.125,1.948 false 0.177,0.125 0.792,0.531 0.615,0.406 10 false *a 0.552,1.229 0.979,1.5 0.427,0.271 10 false G71 0.573,0.458 1.156,0.688 0.583,0.229 10 false CANH*b 0.604,1.875 1.177,2.094 0.573,0.219 10 false CANL*b

Disconnect the G71 CAN junction connector LH (instrument panel wire side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G71-4 (CANH) - G71-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN junction connector RH


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to CAN Junction Connector RH



OK

6.CHECK FOR OPEN IN CAN BUS LINES (CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE))

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN J/C LH - CAN J/C RH)

6.CHECK FOR OPEN IN CAN BUS LINES (CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE))
a.

Reconnect the G71 CAN junction connector LH (instrument panel wire side).


b.
U159398E03
2.052,1.365 2.052,0.521 2.052,0.521 2.396,0.521 false 2.073,1.573 2.073,1.948 2.073,1.948 2.406,1.948 false 0.104,0 0.719,0.406 0.615,0.406 10 false *a 0.552,1.229 0.979,1.5 0.427,0.271 10 false A51 2.469,0.427 3.052,0.656 0.583,0.229 10 false CANH*b 2.49,1.854 3.063,2.073 0.573,0.219 10 false CANL*b

Disconnect the A51 CAN junction connector LH (engine room main wire side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A51-9 (CANH) - A51-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to ECM



OK

REPLACE CAN JUNCTION CONNECTOR LH

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN J/C LH - ECM)