This DTC is stored when a malfunction in the ACC circuit is detected. The ACC circuit activates the ACC relay.
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
| DTC Code | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
|---|---|---|---|
| B2274 | Malfunction in the ACC circuit of the certification ECU (smart key ECU assembly)(1-trip detection logic*).
|
·
AM2 fuse ·
ACC relay (Instrument panel junction block assembly) ·
Certification ECU (Smart key ECU assembly) ·
Wire harness or connector |
Wait 10 seconds after turning the power switch on (ACC) or on (IG), and then wait another 10 seconds after turning the power switch off. |
*: Only detected while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
·
If there is a malfunction due to the relay being stuck on, the ACC relay does not turn off even though the power switch is off. ·
If there is a malfunction due to the relay being stuck off, the ACC relay does not turn on even though the power switch is on (ACC).
|
- |
When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:
for Power Source Control: Body / Power Source Control / DTC.
for Entry&Start: Body / Entry&Start / DTC.
The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
| DTC | Data List Item | Active Test Item |
|---|---|---|
| B2274 | Power Source Control
·
ACC Relay Monitor |
- |
OK
NG
OK
NG
Disconnect the G79 connector from the certification ECU (smart key ECU assembly).
Disconnect the 3B connector from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G79-4 (ACCD) - 3B-37 | Always | Below 1 Ω |
| 3B-8 - Body ground | Always | Below 1 Ω |
| G79-4 (ACCD) or 3B-37 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
| *1 | for LHD | *2 | for RHD |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3E-1 - 3B-13*1
3F-1 - 3B-13*2 |
Auxiliary battery voltage not applied to terminals 3B-37 and 3B-8 | 10 kΩ or higher |
| Auxiliary battery voltage applied to terminals 3B-37 and 3B-8 | Below 1 Ω |
*1: for LHD
*2: for RHD
OK
NG
Reconnect the G79 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G79-4 (ACCD) - Body ground | Power switch off → Power switch on (ACC) | 1 V or less → 8.5 V or higher |
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG