Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2015.11–2019.07
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278081 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.

·

With the electrical key transmitter sub-assembly in the cabin, the power switch is pressed.

·

When the transmitter battery of the electrical key transmitter sub-assembly is depleted, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the power switch.

·

When the smart entry and start system cancel function has been canceled on the customization menu, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the power switch.


HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


WIRING DIAGRAM

B399051E02
2.927,1.542 3.302,1.74 0.375,0.198 10 false IG1D 3.396,1.375 3.531,1.542 0.135,0.167 10 false 6 2.833,4.073 3.271,4.271 0.438,0.198 10 false ACCD 3.396,3.865 3.521,4.031 0.125,0.167 10 false 4 4.948,1.875 5.646,2.073 0.698,0.198 10 false IG1 NO. 1 4.948,3.094 5.646,3.292 0.698,0.198 10 false IG1 NO. 2 2.229,7.281 3.844,7.719 1.615,0.438 10 false Certification ECU (Smart Key ECU Assembly) 3.885,4.771 6.583,4.938 2.698,0.167 10 false Instrument Panel Junction Block Assembly 5.188,6.75 5.469,6.948 0.281,0.198 10 false IG2 3.302,4.042 3.625,4.208 0.323,0.167 10 false G79 3.302,1.563 3.625,1.729 0.323,0.167 10 false G79 3.865,1.135 4.104,1.302 0.24,0.167 10 false 3E 3.854,0.948 4.083,1.115 0.229,0.167 10 false 1*1 4.198,1.135 4.438,1.302 0.24,0.167 10 false 3F 4.177,0.948 4.406,1.115 0.229,0.167 10 false 1*2 3.865,1.552 4.104,1.719 0.24,0.167 10 false 3A 3.885,1.365 4.125,1.531 0.24,0.167 10 false 29 6.469,1.146 6.688,1.313 0.219,0.167 10 false 3A 6.479,2.365 6.698,2.531 0.219,0.167 10 false 3A 6.479,3.625 6.698,3.792 0.219,0.167 10 false 3B 6.479,4.042 6.698,4.208 0.219,0.167 10 false 3B 3.865,4.042 4.083,4.208 0.219,0.167 10 false 3B 6.5,0.969 6.719,1.135 0.219,0.167 10 false 54 5.958,2.51 6.458,2.708 0.5,0.198 10 false WIPER 5.917,1.271 6.479,1.615 0.563,0.344 10 false ECU-IG NO. 1 6.552,2.177 6.792,2.344 0.24,0.167 10 false 9 6.51,3.438 6.75,3.604 0.24,0.167 10 false 13 3.875,3.865 4.115,4.031 0.24,0.167 10 false 37 6.021,3.75 6.396,3.969 0.375,0.219 10 false ACC 6.531,3.854 6.771,4.021 0.24,0.167 10 false 8 3.927,5.833 4.167,6 0.24,0.167 10 false 4 3.885,6.01 4.104,6.177 0.219,0.167 10 false 2D 0.188,1.135 1.073,1.552 0.885,0.417 10 false from Auxiliary Battery 1.396,1.292 1.729,1.479 0.333,0.188 10 false AM2 2.49,1.135 2.927,1.281 0.438,0.146 10 false +B 2.229,0.958 2.344,1.104 0.115,0.146 10 false 2 2.125,1.146 2.406,1.333 0.281,0.188 10 false G77 2.5,2.594 2.938,2.74 0.438,0.146 10 false E 2.208,2.406 2.385,2.552 0.177,0.146 10 false 11 2.135,2.604 2.417,2.792 0.281,0.188 10 false G77 0.479,4.917 1.49,5.083 1.01,0.167 10 false Power Switch 0.469,4.771 0.781,4.938 0.313,0.167 10 false G48 1,3.969 1.438,4.115 0.438,0.146 10 false SS1 1.021,4.406 1.458,4.552 0.438,0.146 10 false SS2 1.365,3.865 1.479,4.01 0.115,0.146 10 false 5 1.365,4.302 1.479,4.448 0.115,0.146 10 false 1 2.5,3.938 2.938,4.083 0.438,0.146 10 false SSW1 2.5,4.417 2.938,4.563 0.438,0.146 10 false SSW2 2.198,3.781 2.385,3.927 0.188,0.146 10 false 28 2.135,3.969 2.438,4.156 0.302,0.188 10 false G79 2.198,4.219 2.385,4.365 0.188,0.146 10 false 30 2.135,4.406 2.438,4.594 0.302,0.188 10 false G79 2.198,5.438 2.417,5.604 0.219,0.167 10 false 18 2.5,5.625 2.875,5.792 0.375,0.167 10 false STP1 2.135,5.615 2.458,5.781 0.323,0.167 10 false G77 1.188,7.094 2.094,7.563 0.906,0.469 10 false from Auxiliary Battery 0.396,6.26 0.708,6.427 0.313,0.167 10 false A65 0.385,6.427 2.219,6.76 1.833,0.333 10 false Stop Light Switch Assembly 0.448,7.24 0.906,7.406 0.458,0.167 10 false STOP 0.25,8.344 0.979,8.51 0.729,0.167 10 false *2: for RHD 0.25,7.99 0.958,8.156 0.708,0.167 10 false *1: for LHD 1.625,5.531 1.76,5.698 0.135,0.167 10 false 2 1.625,5.948 1.76,6.115 0.135,0.167 10 false 3 0.729,5.729 0.865,5.896 0.135,0.167 10 false 1 1.229,5.604 1.583,5.771 0.354,0.167 10 false OUT 0.906,5.823 1.042,5.99 0.135,0.167 10 false B 1.219,6.042 1.573,6.24 0.354,0.198 10 false GND 5.115,4.344 5.49,4.563 0.375,0.219 10 false ACC 2.917,6.427 3.26,6.625 0.344,0.198 10 false IG2D 3.427,6.25 3.667,6.417 0.24,0.167 10 false 9 3.313,6.427 3.646,6.594 0.333,0.167 10 false G77 3.927,6.26 4.167,6.427 0.24,0.167 10 false 3 3.885,6.438 4.104,6.604 0.219,0.167 10 false 2D 6.542,6.26 6.781,6.427 0.24,0.167 10 false 2 6.5,6.438 6.719,6.604 0.219,0.167 10 false 2D 6.542,5.844 6.781,6.01 0.24,0.167 10 false 1 6.5,6.021 6.719,6.188 0.219,0.167 10 false 2E 5.917,6.146 6.198,6.344 0.281,0.198 10 false IG2 4.583,7.125 6.135,7.438 1.552,0.313 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the electrical key transmitter sub-assembly, refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>PRECAUTION).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
·

Start Switch1

·

Start Switch2

·

Power Supply Condition

·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Inside)

·

IG1 Relay Monitor(Outside)

·

IG2 Relay Monitor(Outside)

·

Latch Circuit

·

ACC Relay Monitor


-


PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check the wireless door lock function by operating the electrical key transmitter sub-assembly.

OK:

Wireless door lock function operates.




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

GO TO OTHER DIAGNOSIS PROCEDURE (All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)

OK

4.CHECK SMART ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SMART ENTRY AND START SYSTEM
a.

Remove the transmitter battery from the electrical key transmitter sub-assembly (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT).


b.
B431431E05
0.813,2.635 0.948,2.635 0.948,2.635 1.229,2.917 false 2.625,3.646 2.5,3.646 2.5,3.646 2.219,3.375 false 0.813,0.49 0.948,0.49 0.948,0.49 1.229,0.771 false 2.625,1.49 2.5,1.49 2.5,1.49 2.219,1.229 false 0.625,2.542 0.813,2.729 0.188,0.188 10 false *1 2.656,3.563 2.844,3.75 0.188,0.188 10 false *2 0.625,0.396 0.813,0.583 0.188,0.188 10 false *1 0.188,0.104 0.417,0.313 0.229,0.208 12 false *A 0.188,2.208 0.417,2.417 0.229,0.208 12 false *B 2.688,1.417 2.875,1.604 0.188,0.188 10 false *2

With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch and check if the power source mode changes.

OK:

The power source mode changes.


HINT:

If the power source mode changes, the cabin verification is malfunctioning.


Result:
Result Proceed to
The power source mode does not change. A
The power source mode changes. B


Text in Illustration
*A for Type A
*B for Type B
*1 Power Switch
*2 Electrical Key Transmitter Sub-assembly



A

5.READ VALUE USING INTELLIGENT TESTER

B

8.READ VALUE USING INTELLIGENT TESTER
5.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Specified Condition
Stop Light Switch1 State of brake pedal/ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.

·

When this item is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.



OK:

ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.




OK

6.READ VALUE USING INTELLIGENT TESTER

NG

11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)
6.READ VALUE USING INTELLIGENT TESTER
a.

Read the Data List according to the display on the intelligent tester.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON All OFF: Power switch off
ACC ON: Power switch on (ACC)
IG1 ON: Power switch on (IG) (IG1 relay on)
IG2 ON: Power switch on (IG) (IG2 relay on)
ST ON: Sending hybrid control system start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).


b.

With the power switch off and brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch for 2 seconds or more and read the Data List.

OK:

IG2 ON is displayed in the Data List.


HINT:

If the smart entry and start system function has been canceled on the customization menu, ACC ON is displayed in the Data List.




OK

7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

14.CHECK FOR DTC
7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Read the Data List according to the display on the intelligent tester.

U183379E01
0.302,0.29 0.488,0.451 0.186,0.161 10 *a 4.799,0.934 5.094,1.090 0.295,0.156 10 G79 2.175,0.932 2.470,1.088 0.295,0.156 10 G77 4.388,1.629 4.096,2.312 false 1.978,1.736 1.704,2.287 false 3.927,2.312 4.290,2.468 0.363,0.156 10 IG1D 1.531,2.313 1.893,2.469 0.363,0.156 10 IG2D 4.538,1.626 4.834,2.311 false 4.647,2.325 5.076,2.481 0.429,0.156 10 ACCD

Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


b.

Measure the voltage according to the value(s) in the table below.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON All OFF: Power switch off
ACC ON: Power switch on (ACC)
IG1 ON: Power switch on (IG) (IG1 relay on)
IG2 ON: Power switch on (IG) (IG2 relay on)
ST ON: Sending hybrid control system start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).


c.

Measure the voltage while checking the Data List on the intelligent tester.

Standard Voltage:
Tester Connection Condition Specified Condition
G79-6 (IG1D) - Body ground Power switch off 1 V or less
Power switch on (ACC) 1 V or less
Power switch on (IG) 9 V or higher
G77-9 (IG2D) - Body ground Power switch off 1 V or less
Power switch on (ACC) 1 V or less
Power switch on (IG) 9 V or higher
G79-4 (ACCD) - Body ground Power switch off 1 V or less
Power switch on (IG) 8.5 V or higher
Power switch on (ACC) 8.5 V or higher




OK

CHECK RELAY CONTACT SIDE CIRCUIT

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.READ VALUE USING INTELLIGENT TESTER
a.

Read the Data List according to the display on the intelligent tester.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Start Switch1 Power switch 1 status/ON or OFF ON: Power switch pressed
OFF: Power switch not pressed
·

If the power switch is pressed for a short time, the display may not change.

·

Use this item to determine whether the power switch input signal is malfunctioning.


Start Switch2 Power switch 2 status/ON or OFF ON: Power switch pressed
OFF: Power switch not pressed
·

Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal.

·

Behaves the same way as power switch 1.



OK:

ON (Power switch is pressed) and OFF (Power switch is not pressed) appear on the screen.


Result:
Result Proceed to
NG A
OK B




A

9.INSPECT POWER SWITCH

B

9.INSPECT POWER SWITCH
a.


OK

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER SWITCH)

NG

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER SWITCH)
a.

Disconnect the G79 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G48 power switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-28 (SSW1) - G48-5 (SS1) Always Below 1 Ω
G79-30 (SSW2) - G48-1 (SS2) Always Below 1 Ω
G79-28 (SSW1) or G48-5 (SS1) - Body ground Always 10 kΩ or higher
G79-30 (SSW2) or G48-1 (SS2) - Body ground Always 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)
a.
U183738E02
1.333,1.292 1.042,1.75 false 1.719,1.292 2,1.771 false 0.219,0.125 0.573,0.417 0.354,0.292 10 false *a 1.594,0.208 1.948,0.5 0.354,0.292 10 false A65 0.958,1.75 1.125,1.938 0.167,0.188 10 false B 1.854,1.771 2.219,1.958 0.365,0.188 10 false GND

Disconnect the A65 stop light switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A65-1 (B) - A65-3 (GND) Power switch off 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
A65-3 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

12.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
U183743E01
0.245,0.128 0.447,0.302 0.202,0.174 10 *a 1.583,0.196 1.943,0.370 0.360,0.174 10 A65 2.583,1.623 2.953,1.798 0.370,0.174 10 OUT 2.051,1.625 2.475,1.799 0.424,0.174 10 GND 2.59,1.617 1.954,1.274 false 1.758,1.286 2.216,1.626 false

Reconnect the A65 stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A65-2 (OUT) - A65-3 (GND) Power switch off, brake pedal not depressed Below 1 V
A65-2 (OUT) - A65-3 (GND) Power switch off, brake pedal depressed 11 to 14 V


Text in Illustration
*a Component with harness connected
(Stop Light Switch Assembly)



OK

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STOP LIGHT SWITCH ASSEMBLY)

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK FOR DTC
a.

Enter the following menus:

for Entry&Start: Body / Entry&Start / Trouble Codes.


b.

Check for DTCs.

Result:
Result Proceed to
The following DTCs are not output:
·

B2785

·

B2784

·

B278A


A
The following DTCs are output:
·

B2784

·

B278A


B
DTC B2785 is output. C




A

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

C