Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2013.12–2014.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278081 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2285  Steering Lock Position Signal Circuit Malfunction  


DESCRIPTION

This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN communication do not match.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2285 The steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN communication (1-trip detection logic*) do not match.
·

AM2 fuse

·

Steering lock ECU (steering lock actuator assembly)

·

Power management control ECU

·

Wire harness or connector


Disconnect the cable from the negative (-) auxiliary battery terminal, wait 30 seconds and then reconnect the cable to the negative (-) auxiliary battery terminal. Wait 40 seconds or more with the power switch off (with the steering wheel locked), then turn the power switch on (ACC) (with the steering unlocked) and wait 40 seconds or more.

*: Only detected while a malfunction is present and the power switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The hybrid control system cannot be started. The ECU does not send an hybrid control system start request.

WIRING DIAGRAM

B300417E03
0.646,1.927 0.927,2.104 0.281,0.177 10 false G50 2.427,1.438 3.979,1.615 1.552,0.177 10 false LIN Communication Line 2.896,0.625 3.229,0.802 0.333,0.177 10 false AM2 0.646,2.083 2.458,2.448 1.813,0.365 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 4.24,2.104 5.521,2.51 1.281,0.406 10 false Power Management Control ECU 2.25,1.615 2.344,1.771 0.094,0.156 10 false 4 1.813,1.719 2.354,1.938 0.542,0.219 10 false SLP1 5,0.479 5.281,0.625 0.281,0.146 10 false E01 5.448,0.292 5.563,0.438 0.115,0.146 10 false 5 5.365,0.479 5.646,0.625 0.281,0.146 10 false G57 5.01,0.875 5.448,1.021 0.438,0.146 10 false E02 5.458,0.677 5.573,0.823 0.115,0.146 10 false 5 5.354,0.875 5.635,1.063 0.281,0.188 10 false G58 5.073,1.271 5.51,1.417 0.438,0.146 10 false E1 5.469,1.094 5.583,1.24 0.115,0.146 10 false 6 5.365,1.26 5.646,1.448 0.281,0.188 10 false G57 1.5,0.469 2.396,0.938 0.896,0.469 10 false from Auxiliary Battery 4.427,0.469 4.865,0.615 0.438,0.146 10 false AM21 4.156,0.281 4.271,0.427 0.115,0.146 10 false 7 4.042,0.49 4.323,0.635 0.281,0.146 10 false G58 4.427,0.875 4.865,1.021 0.438,0.146 10 false AM22 4.146,0.677 4.26,0.823 0.115,0.146 10 false 1 4.042,0.875 4.323,1.063 0.281,0.188 10 false G57 4.115,1.083 4.292,1.229 0.177,0.146 10 false 11 4.042,1.271 4.323,1.458 0.281,0.188 10 false G58 4.104,1.521 4.354,1.667 0.25,0.146 10 false 16 4.042,1.708 4.323,1.896 0.281,0.188 10 false G58 4.427,1.708 4.865,1.854 0.438,0.146 10 false SLP 4.438,1.281 4.875,1.427 0.438,0.146 10 false LIN2 2.24,1.135 2.333,1.292 0.094,0.156 10 false 5 1.927,1.26 2.281,1.438 0.354,0.177 10 false LIN

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the steering lock ECU (steering lock actuator assembly), refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>PRECAUTION).

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2285
Power Source Control

Steering Unlock Switch


Entry&Start
·

Power Supply Short

·

Motor Driver Short

·

Lock Bar Stuck Error


-


PROCEDURE

1.CHECK FOR DTC (LIN COMMUNICATION SYSTEM)
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

LIN communication system DTC B2785 is not output simultaneously.


HINT:
·

If the steering wheel cannot be locked or unlocked, the power switch cannot be turned on (IG) and the hybrid control system cannot be started.

·

If LIN communication is not available, the steering wheel cannot be locked or unlocked.





OK

2.READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH)

NG

2.READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Steering Unlock Switch State of steering unlock sensor signal output from steering lock actuator assembly/ON or OFF ON: Steering unlocked
OFF: Steering locked
·

When the shift lever is in P and the power switch is off, if any door is opened or closed, the steering is locked.

·

When the electrical key transmitter sub-assembly is inside the vehicle and the power switch is turned on (ACC) or on (IG), the steering unlocks.

·

The hybrid control system cannot be started when the steering unlock signal is off.



Result:
Result Proceed to
Data List item does not change A
Data List item changes B




A

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

4.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

4.CHECK HARNESS AND CONNECTOR (GROUND)

OK

5.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.
U159330E03
1.135,1.948 1.313,1.948 1.313,1.948 1.698,1.177 false 0.771,1.875 1.396,2.156 0.625,0.281 10 false SLP1 0.135,0.104 0.375,0.292 0.24,0.188 10 false *a 0.333,0.688 0.896,1.01 0.563,0.323 10 false G50

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) tester probe → G50-4 (SLP1)
Negative (-) tester probe → Body ground
Steering locked* 10 kΩ or higher
Steering unlocked* Below 1 Ω


HINT:
·

*: If any of the doors are opened then closed with the shift lever in P and the power switch off, the steering wheel will be locked. If the power switch is then turned on (ACC) or on (IG), the steering wheel will be unlocked.

·

DTC B2285 may be stored due to a malfunction in the steering lock ECU (steering lock actuator assembly). The steering lock position signal and unlock position signal are sent from the steering lock ECU (steering lock actuator assembly) to the power management control ECU individually.



Text in Illustration
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))



OK

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Disconnect the G58 connector from the power management control ECU.


b.

Disconnect the G50 connector from the steering lock ECU (steering lock actuator assembly).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-16 (SLP) - G50-4 (SLP1) Always Below 1 Ω
G58-16 (SLP) or G50-4 (SLP1) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR