Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM2170E _58 Vehicle Interior _057036 LIGHTING (INT) _0278087 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Back Door Courtesy Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the back door lock assembly using this circuit.

WIRING DIAGRAM

E227473E29
1.677,0.813 1.833,0.969 0.156,0.156 10 false 2 2.99,0.813 3.354,0.969 0.365,0.156 10 false 3 5.708,0.906 6.021,1.063 0.313,0.156 10 false MB 5.74,0.708 6,0.896 0.26,0.188 10 false 20 6.083,0.896 6.698,1.115 0.615,0.219 10 false BCTY 1.604,1.135 1.844,1.292 0.24,0.156 10 false T5 1.604,1.292 3.323,1.604 1.719,0.313 10 false Back Door Lock Assembly 4.01,1.49 5.625,1.885 1.615,0.396 10 false Instrument Panel Junction Block Assembly 5.479,2.052 7.125,2.583 1.646,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 4.521,0.896 4.833,1.052 0.313,0.156 10 false 3D 4.531,0.708 4.906,0.865 0.375,0.156 10 false 35 1.875,0.813 2.396,0.969 0.521,0.156 10 false ACT- 2.719,0.813 2.969,0.969 0.25,0.156 10 false D+

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the display on the intelligent tester.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Back Door Courtesy SW Back door courtesy switch signal/ON or OFF ON: Back door open
OFF: Back door closed
-

OK:

Normal conditions listed above are displayed.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT BACK DOOR LOCK ASSEMBLY
2.INSPECT BACK DOOR LOCK ASSEMBLY
a.

Remove the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL).


b.

Inspect the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION).

OK:

Back door lock assembly is normal.




OK

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T5-3 (D+) - 3D-35 Always Below 1 Ω
T5-3 (D+) - Body ground Always 10 kΩ or higher
T5-2 (ACT-) - Body ground Always Below 1 Ω




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U159631E01
1.198,0.324 1.455,0.531 0.258,0.207 10 3D 4.789,0.432 5.047,0.638 0.258,0.207 10 MB 5.372,1.534 5.810,1.692 0.438,0.158 10 BCTY 5.264,1.023 5.428,1.513 false 0.128,0.077 0.312,0.265 0.184,0.188 10 *a

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3D-35 - MB-20 (BCTY) Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY