Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057037 METER / GAUGE / DISPLAY _0278095 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light circuit.

DTC No. DTC Detection Condition Trouble Area
B1507 When IG voltage is 9.5 V or more and the following condition is detected:
1.

Open in turn signal light circuit


·

Harness or connector

·

Bulb

·

Instrument panel junction block assembly

·

Combination meter assembly


B1508 When IG voltage is 9.5 V or more and the following condition is detected:
1.

Short in turn signal light circuit or hazard warning light circuit


·

Harness or connector

·

Bulb

·

Instrument panel junction block assembly

·

Combination meter assembly



WIRING DIAGRAM

for Halogen Headlight


U183686E02
3.292,5.99 4.927,6.646 1.635,0.656 10 false Instrument Panel Junction Block Assembly 0.677,0.979 2.844,1.302 2.167,0.323 10 false Headlight Assembly LH 0.667,0.833 0.958,1.01 0.292,0.177 10 false A8 0.521,1.969 2.938,2.292 2.417,0.323 10 false Rear Combination Light Assembly LH 0.521,1.792 0.813,1.969 0.292,0.177 10 false M5 0.521,2.979 3.021,3.302 2.5,0.323 10 false Outer Rear View Mirror Assembly LH 0.521,2.813 0.813,2.99 0.292,0.177 10 false J7 0.708,3.906 2.875,4.229 2.167,0.323 10 false Headlight Assembly RH 0.708,3.74 1,3.917 0.292,0.177 10 false A7 0.542,4.927 2.927,5.25 2.385,0.323 10 false Rear Combination Light Assembly RH 0.542,4.75 0.833,4.927 0.292,0.177 10 false M6 5.26,5.979 7.135,6.177 1.875,0.198 10 false Combination Meter Assembly 5.26,5.823 5.552,6 0.292,0.177 10 false G3 4.771,3.531 4.969,3.708 0.198,0.177 10 false 3B 4.781,3.323 4.979,3.5 0.198,0.177 10 false 25 4.781,0.615 4.979,0.792 0.198,0.177 10 false 3B 4.781,0.427 4.979,0.604 0.198,0.177 10 false 24 3.094,3.531 3.292,3.708 0.198,0.177 10 false 3C 3.104,3.323 3.302,3.5 0.198,0.177 10 false 38 3.094,0.615 3.292,0.792 0.198,0.177 10 false 3C 3.094,0.438 3.292,0.615 0.198,0.177 10 false 28 3.083,1.604 3.281,1.781 0.198,0.177 10 false 3D 3.094,1.417 3.292,1.594 0.198,0.177 10 false 18 3.094,4.563 3.292,4.74 0.198,0.177 10 false 3D 3.146,4.375 3.323,4.552 0.177,0.177 10 false 5 5.833,0.531 6.031,0.708 0.198,0.177 10 false 13 5.885,3.417 6.083,3.594 0.198,0.177 10 false 7 6.094,3.521 6.292,3.698 0.198,0.177 10 false LR 6.094,0.583 6.292,0.76 0.198,0.177 10 false LL 2.104,1.51 2.229,1.688 0.125,0.177 10 false B 2.094,4.448 2.229,4.625 0.135,0.177 10 false B 1.115,1.5 1.427,1.677 0.313,0.177 10 false E 1.115,4.469 1.427,4.646 0.313,0.177 10 false E 2.281,1.5 2.594,1.677 0.313,0.177 10 false 5 0.938,1.5 1.094,1.677 0.156,0.177 10 false 1 2.281,0.5 2.594,0.677 0.313,0.177 10 false 1 0.938,0.51 1.094,0.688 0.156,0.177 10 false 2 2.281,4.448 2.594,4.625 0.313,0.177 10 false 5 0.938,4.469 1.094,4.646 0.156,0.177 10 false 1 2.281,3.438 2.594,3.615 0.313,0.177 10 false 1 0.938,3.438 1.094,3.615 0.156,0.177 10 false 2 2.104,0.51 2.229,0.688 0.125,0.177 10 false B 1.115,0.5 1.25,0.677 0.135,0.177 10 false E 3.094,2.604 3.292,2.781 0.198,0.177 10 false 3B 3.094,2.406 3.292,2.583 0.198,0.177 10 false 38 2.104,2.51 2.229,2.688 0.125,0.177 10 false B 1.115,2.5 1.427,2.677 0.313,0.177 10 false - 2.281,2.5 2.594,2.677 0.313,0.177 10 false 2 0.885,2.51 1.063,2.688 0.177,0.177 10 false 9 2.104,3.448 2.229,3.625 0.125,0.177 10 false B 1.115,3.438 1.25,3.615 0.135,0.177 10 false E 0.5,5.948 3.042,6.271 2.542,0.323 10 false Outer Rear View Mirror Assembly RH 0.5,5.802 0.792,5.979 0.292,0.177 10 false H7 3.083,5.583 3.281,5.76 0.198,0.177 10 false 3B 3.094,5.375 3.271,5.552 0.177,0.177 10 false 39 2.094,5.479 2.229,5.656 0.135,0.177 10 false B 1.115,5.49 1.427,5.667 0.313,0.177 10 false - 2.281,5.469 2.594,5.646 0.313,0.177 10 false 2 0.885,5.49 1.094,5.667 0.208,0.177 10 false 9


for LED Headlight


U183685E02
3.292,5.99 5.063,6.646 1.771,0.656 10 false Instrument Panel Junction Block Assembly 0.677,1.042 2.844,1.365 2.167,0.323 10 false Headlight Assembly LH 0.677,0.906 0.969,1.083 0.292,0.177 10 false A8 0.521,2.01 2.938,2.333 2.417,0.323 10 false Rear Combination Light Assembly LH 0.521,1.844 0.813,2.021 0.292,0.177 10 false M5 0.531,2.979 3.031,3.302 2.5,0.323 10 false Outer Rear View Mirror Assembly LH 0.552,2.813 0.844,2.99 0.292,0.177 10 false J7 0.708,3.979 2.875,4.302 2.167,0.323 10 false Headlight Assembly RH 0.708,3.813 1,3.99 0.292,0.177 10 false A62 0.542,4.938 2.927,5.26 2.385,0.323 10 false Rear Combination Light Assembly RH 0.542,4.76 0.833,4.938 0.292,0.177 10 false M6 5.26,6.021 7.135,6.219 1.875,0.198 10 false Combination Meter Assembly 5.26,5.854 5.552,6.031 0.292,0.177 10 false G3 4.771,3.542 4.969,3.719 0.198,0.177 10 false 3B 4.792,3.333 4.99,3.51 0.198,0.177 10 false 25 4.76,0.635 4.958,0.813 0.198,0.177 10 false 3B 4.781,0.427 4.979,0.604 0.198,0.177 10 false 24 3.094,3.552 3.292,3.729 0.198,0.177 10 false 3C 3.115,3.333 3.313,3.51 0.198,0.177 10 false 38 3.094,0.625 3.292,0.802 0.198,0.177 10 false 3C 3.104,0.427 3.302,0.604 0.198,0.177 10 false 28 3.094,1.604 3.292,1.781 0.198,0.177 10 false 3D 3.104,1.406 3.302,1.583 0.198,0.177 10 false 18 3.104,4.573 3.302,4.75 0.198,0.177 10 false 3D 3.156,4.365 3.333,4.542 0.177,0.177 10 false 5 5.823,0.521 6.021,0.698 0.198,0.177 10 false 13 5.875,3.417 6.073,3.594 0.198,0.177 10 false 7 6.063,3.542 6.26,3.719 0.198,0.177 10 false LR 6.073,0.615 6.271,0.792 0.198,0.177 10 false LL 2.104,1.49 2.229,1.667 0.125,0.177 10 false B 2.094,4.448 2.229,4.625 0.135,0.177 10 false B 1.125,1.49 1.438,1.667 0.313,0.177 10 false E 1.125,4.438 1.438,4.615 0.313,0.177 10 false E 2.292,1.49 2.604,1.667 0.313,0.177 10 false 5 0.938,1.49 1.094,1.667 0.156,0.177 10 false 1 2.281,0.51 2.594,0.688 0.313,0.177 10 false 1 0.938,0.5 1.094,0.677 0.156,0.177 10 false 2 2.281,4.438 2.594,4.615 0.313,0.177 10 false 5 0.938,4.438 1.094,4.615 0.156,0.177 10 false 1 2.292,3.396 2.604,3.573 0.313,0.177 10 false 1 0.938,3.417 1.094,3.594 0.156,0.177 10 false 2 2.104,0.51 2.229,0.688 0.125,0.177 10 false B 1.125,0.5 1.26,0.677 0.135,0.177 10 false E 3.094,2.615 3.292,2.792 0.198,0.177 10 false 3B 3.104,2.417 3.302,2.594 0.198,0.177 10 false 38 2.104,2.5 2.229,2.677 0.125,0.177 10 false B 1.125,2.49 1.438,2.667 0.313,0.177 10 false - 2.281,2.49 2.594,2.667 0.313,0.177 10 false 2 0.958,2.5 1.135,2.677 0.177,0.177 10 false 9 2.104,3.406 2.229,3.583 0.125,0.177 10 false B 1.115,3.417 1.25,3.594 0.135,0.177 10 false E 0.5,6.01 3.042,6.333 2.542,0.323 10 false Outer Rear View Mirror Assembly RH 0.5,5.833 0.792,6.01 0.292,0.177 10 false H7 3.104,5.594 3.302,5.771 0.198,0.177 10 false 3B 3.115,5.385 3.292,5.563 0.177,0.177 10 false 39 2.094,5.479 2.229,5.656 0.135,0.177 10 false B 1.125,5.479 1.438,5.656 0.313,0.177 10 false - 2.281,5.479 2.594,5.656 0.313,0.177 10 false 2 0.885,5.479 1.094,5.656 0.208,0.177 10 false 9


CAUTION / NOTICE / HINT

NOTICE:

Inspect the bulbs for this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
Turn signal lights for one side do not illuminate. A
Front turn signal light does not illuminate. B
Rear turn signal light does not illuminate. C
Side turn signal light does not illuminate. D



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

C

4.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

D

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G3 combination meter assembly connector.


b.

Disconnect the 3B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
G3-13 (LL) - 3B-24 Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
G3-7 (LR) - 3B-25 Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
G3-13 (LL) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
G3-7 (LR) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
NG A
OK B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

for Halogen Headlight

i.

Disconnect the A7*1 or A8*2 front turn signal light connector.

*1: for RH

*2: for LH



ii.

Disconnect the 3C instrument panel junction block assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
A8-1 (B) - 3C-28 Always Below 1 Ω
A8-2 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
A7-1 (B) - 3C-38 Always Below 1 Ω
A7-2 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
A8-1 (B) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A7-1 (B) - Body ground Always 10 kΩ or higher




b.

for LED Headlight

i.

Disconnect the A62*1 or A8*2 front turn signal light connector.

*1: for RH

*2: for LH



ii.

Disconnect the 3C instrument panel junction block assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
A8-1 (B) - 3C-28 Always Below 1 Ω
A8-2 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
A62-1 (B) - 3C-38 Always Below 1 Ω
A62-2 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
A8-1 (B) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A62-1 (B) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
NG A
OK B





A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the M6*1 or M5*2 rear turn signal light connector.

*1: for RH

*2: for LH



b.

Disconnect the 3D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
M5-5 (B) - 3D-18 Always Below 1 Ω
M5-1 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
M6-5 (B) - 3D-5 Always Below 1 Ω
M6-1 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
M5-5 (B) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
M6-5 (B) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
NG A
OK B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the H7*1 or J7*2 outer rear view mirror assembly connector.

*1: for RH

*2: for LH



b.

Disconnect the 3B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
J7-2 (B) - 3B-38 Always Below 1 Ω
J7-9 (-) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
H7-2 (B) - 3B-39 Always Below 1 Ω
H7-9 (-) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
J7-2 (B) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
H7-2 (B) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
NG A
OK B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U183702E02
1.177,0.969 1.5,1.135 0.323,0.167 10 false 3B 0.052,0 0.375,0.167 0.323,0.167 10 false *a 5.802,0.948 6.125,1.115 0.323,0.167 10 false 3D 3.458,0.979 3.781,1.146 0.323,0.167 10 false 3C


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
3B-25 - 3C-38 Always Below 1 Ω
3B-25 - 3D-5 Always Below 1 Ω
3B-25 - 3B-39 Always Below 1 Ω
3B-24 - 3C-28 Always Below 1 Ω
3B-24 - 3D-18 Always Below 1 Ω
3B-24 - 3B-38 Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY