Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.12–2015.11
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1820/55  Short in Side Squib RH Circuit  B1821/55  Open in Side Squib RH Circuit  B1822/55  Short to GND in Side Squib RH Circuit  B1823/55  Short to B+ in Side Squib RH Circuit  


DESCRIPTION

The side squib RH circuit consists of the airbag sensor assembly and front seat airbag assembly RH.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the side squib RH circuit.

DTC No. DTC Detection Condition Trouble Area
B1820/55
·

The airbag sensor assembly receives a line short circuit signal in the side squib RH circuit during primary check.

·

Side squib RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat airbag assembly RH (Side squib RH)

·

Airbag sensor assembly


B1821/55
·

The airbag sensor assembly receives an open circuit signal in the side squib RH circuit.

·

Side squib RH malfunction

·

Airbag sensor assembly malfunction


B1822/55
·

The airbag sensor assembly receives a short circuit to ground signal in the side squib RH circuit.

·

Side squib RH malfunction

·

Airbag sensor assembly malfunction


B1823/55
·

The airbag sensor assembly receives a short circuit to B+ signal in the side squib RH circuit.

·

Side squib RH malfunction

·

Airbag sensor assembly malfunction



WIRING DIAGRAM

C249389E01
0.695,2.481 1.116,2.643 0.420,0.163 10 M33 0.695,2.659 2.693,3.011 1.998,0.351 10 Front Seat Airbag Assembly RH (Side Squib RH) 4.648,3.009 5.015,3.154 0.367,0.145 10 M37 4.703,1.986 5.086,2.149 0.384,0.163 10 SFR- 4.53,1.905 4.641,2.068 0.111,0.163 10 6 4.703,1.142 5.198,1.304 0.496,0.163 10 SFR+ 1.973,1.905 2.500,2.068 0.526,0.163 10 SFR- 1.973,1.065 2.436,1.228 0.463,0.163 10 SFR+ 4.53,1.065 4.641,1.228 0.111,0.163 10 7 2.41,1.905 2.521,2.068 0.111,0.163 10 1 2.41,1.065 2.521,1.228 0.111,0.163 10 2 4.648,3.188 6.282,3.364 1.634,0.176 10 Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C238348E04
0.641,1.165 0.761,1.318 0.121,0.153 10 D 1.023,1.165 1.143,1.318 0.121,0.153 10 C 1.604,1.165 1.725,1.318 0.121,0.153 10 B 1.988,1.165 2.109,1.318 0.121,0.153 10 A 2.441,0.867 2.618,1.043 0.177,0.175 10 *2 0.758,0.585 0.910,0.738 0.152,0.152 10 *1 0.543,1.191 0.543,0.673 0.543,0.673 0.716,0.673 false 1.593,0.585 1.745,0.738 0.152,0.152 10 *3 1.378,1.191 1.378,0.673 1.378,0.673 1.55,0.673 false

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat airbag assembly RH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat airbag assembly RH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.


Text in Illustration
*1 Front Seat Airbag Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire



OK

2.CHECK FRONT SEAT AIRBAG ASSEMBLY RH (SIDE SQUIB RH)

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT AIRBAG ASSEMBLY RH (SIDE SQUIB RH)
a.
U159372E02
1.833,2.604 2.021,2.604 false 0.625,0.969 0.625,0.521 0.625,0.521 0.427,0.521 false 0.729,0.948 0.854,1.104 0.125,0.156 10 false D 1.094,0.948 1.219,1.104 0.125,0.156 10 false C 1.604,0.948 1.729,1.104 0.125,0.156 10 false B 1.76,0.948 1.885,1.104 0.125,0.156 10 false A 2.208,0.635 2.385,0.813 0.177,0.177 10 false *2 0.24,0.458 0.396,0.635 0.156,0.177 10 false *1 0.333,1.854 0.51,2.021 0.177,0.167 10 false *a 2.063,2.531 2.354,2.688 0.292,0.156 10 false SST 0.427,2.24 0.719,2.396 0.292,0.156 10 false M33

Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat airbag assembly RH (side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output.


Result:
Result Proceed to
OK (w/ Non-removable Headrest) A
OK (w/ Removable Headrest) B
NG C


HINT:

Codes other than DTCs B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.

Text in Illustration
*1 Front Seat Airbag Assembly RH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Seat Airbag Assembly RH)



A

B

C

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
U159367E01
0.828,1.057 0.949,1.210 0.121,0.153 10 D 1.143,1.057 1.263,1.210 0.121,0.153 10 C 1.594,1.057 1.715,1.210 0.121,0.153 10 B 1.912,1.057 2.032,1.210 0.121,0.153 10 A 2.314,0.777 2.491,0.952 0.177,0.175 10 *2 0.288,0.484 0.440,0.660 0.152,0.175 10 *1 0.217,1.814 0.391,1.979 0.174,0.165 10 *a 1.818,2.584 2.235,2.732 0.417,0.148 10 SFR+ 0.555,2.584 0.939,2.735 0.384,0.151 10 SFR- 1.299,2.669 1.006,2.669 false 1.783,2.669 1.522,2.669 false 0.708,1.074 0.708,0.566 0.708,0.566 0.483,0.566 false 1.003,0.484 1.156,0.660 0.152,0.175 10 *3 1.424,1.074 1.424,0.566 1.424,0.566 1.199,0.566 false 0.389,2.191 0.680,2.347 0.290,0.156 10 M33

Disconnect the floor wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M33-2 (SFR+) - Body ground Power switch on (IG) Below 1 V
M33-1 (SFR-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M33-2 (SFR+) - M33-1 (SFR-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M33-2 (SFR+) - Body ground Always 1 MΩ or higher
M33-1 (SFR-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M33-2 (SFR+) - M33-1 (SFR-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Front Seat Airbag Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Airbag Assembly RH)




OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238241E01
0.958,1.274 1.079,1.427 0.121,0.153 10 D 1.12,1.274 1.241,1.427 0.121,0.153 10 C 1.575,1.274 1.695,1.427 0.121,0.153 10 B 1.727,1.274 1.847,1.427 0.121,0.153 10 A 2.159,0.962 2.336,1.137 0.177,0.175 10 *2 0.471,0.758 0.624,0.933 0.152,0.175 10 *1 0.858,1.29 0.858,0.846 0.858,0.846 0.664,0.846 false

Connect the connectors to the front seat airbag assembly RH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output.


HINT:

Codes other than DTCs B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Airbag Assembly RH
*2 Airbag Sensor Assembly



OK

NG