Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1905/74  Short in Front Pretensioner Squib LH Circuit  B1906/74  Open in Front Pretensioner Squib LH Circuit  B1907/74  Short to GND in Front Pretensioner Squib LH Circuit  B1908/74  Short to B+ in Front Pretensioner Squib LH Circuit  


DESCRIPTION

The front pretensioner squib LH circuit consists of the airbag sensor assembly and front seat outer belt assembly LH.

The airbag sensor assembly uses this circuit to deploy the seat belt pretensioner when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1905/74
·

The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib LH circuit during primary check.

·

Front pretensioner squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Airbag sensor assembly


B1906/74
·

The airbag sensor assembly receives an open circuit signal in the front pretensioner squib LH circuit.

·

Front pretensioner squib LH malfunction

·

Airbag sensor assembly malfunction


B1907/74
·

The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib LH circuit.

·

Front pretensioner squib LH malfunction

·

Airbag sensor assembly malfunction


B1908/74
·

The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib LH circuit.

·

Front pretensioner squib LH malfunction

·

Airbag sensor assembly malfunction



WIRING DIAGRAM

C249389E09
0.695,2.481 1.066,2.643 0.371,0.163 10 M28 0.695,2.659 2.942,3.011 2.247,0.351 10 Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH) 4.648,3.009 5.015,3.154 0.367,0.145 10 M36 4.703,1.986 5.086,2.149 0.384,0.163 10 PL- 4.53,1.905 4.641,2.068 0.111,0.163 10 1 4.703,1.142 5.198,1.304 0.496,0.163 10 PL+ 2.155,1.905 2.682,2.068 0.526,0.163 10 L- 2.155,1.065 2.619,1.228 0.463,0.163 10 L+ 4.53,1.065 4.641,1.228 0.111,0.163 10 2 2.41,1.905 2.521,2.068 0.111,0.163 10 2 2.41,1.065 2.521,1.228 0.111,0.163 10 1 4.648,3.188 6.282,3.364 1.634,0.176 10 Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C241752E03
0.521,1.125 0.521,1.573 false 1.385,0.99 1.385,0.563 1.385,0.563 1.615,0.563 false 0.635,0.969 0.76,1.125 0.125,0.156 10 false D 1.042,0.969 1.167,1.125 0.125,0.156 10 false C 1.625,0.969 1.75,1.125 0.125,0.156 10 false B 2.021,0.969 2.146,1.125 0.125,0.156 10 false A 2.469,0.979 2.646,1.156 0.177,0.177 10 false *2 0.448,1.573 0.604,1.729 0.156,0.156 10 false *1 1.635,0.469 1.792,0.625 0.156,0.156 10 false *3

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat outer belt assembly LH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat outer belt assembly LH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the floor wire connector (on the front seat outer belt assembly LH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.


Text in Illustration
*1 Front Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire



OK

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH)

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH)
a.
U159449E01
0.573,1.277 0.726,1.442 0.153,0.165 10 *1 2.256,0.731 2.421,0.896 0.165,0.165 10 *2 1.813,0.724 1.979,0.889 0.165,0.165 10 A 1.651,0.724 1.817,0.889 0.165,0.165 10 B 1.145,0.724 1.310,0.889 0.165,0.165 10 C 0.772,0.724 0.937,0.889 0.165,0.165 10 D 0.662,0.875 0.662,1.27 false 2.051,2.157 2.369,2.324 0.317,0.167 10 SST 1.853,2.237 2.031,2.237 false 0.308,1.662 0.462,1.827 0.153,0.165 10 *a 0.442,2.095 0.731,2.251 0.289,0.156 10 M28

Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to pretensioner deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTCs B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.

Text in Illustration
*1 Front Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)



OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
U159445E03
0.5,1 0.5,1.396 false 1.448,2.292 1.115,2.292 false 2.031,2.292 1.698,2.292 false 1.375,0.865 1.375,0.427 1.375,0.427 1.167,0.427 false 0.427,1.406 0.583,1.573 0.156,0.167 10 false *1 2.417,0.844 2.583,1.01 0.167,0.167 10 false *2 1.979,0.854 2.146,1.021 0.167,0.167 10 false A 1.594,0.865 1.76,1.031 0.167,0.167 10 false B 1.021,0.865 1.188,1.031 0.167,0.167 10 false C 0.625,0.865 0.792,1.031 0.167,0.167 10 false D 0.365,1.885 0.521,2.052 0.156,0.167 10 false *a 0.979,0.354 1.146,0.521 0.167,0.167 10 false *3 0.677,2.563 1.208,2.917 0.531,0.354 10 false M28 0.885,2.208 1.417,2.563 0.531,0.354 10 false L+ 2.094,2.219 2.625,2.573 0.531,0.354 10 false L-

Disconnect the floor wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M28-1 (L+) - Body ground Power switch on (IG) Below 1 V
M28-2 (L-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M28-1 (L+) - M28-2 (L-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M28-1 (L+) - Body ground Always 1 MΩ or higher
M28-2 (L-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M28-1 (L+) - M28-2 (L-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Front Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)




OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238245E01
0.762,1.589 0.918,1.740 0.156,0.152 10 *1 2.147,0.987 2.322,1.143 0.174,0.156 10 *2 1.73,0.987 1.847,1.140 0.117,0.153 10 A 1.572,0.987 1.689,1.140 0.117,0.153 10 B 1.119,0.987 1.246,1.140 0.127,0.153 10 C 0.962,0.987 1.089,1.140 0.127,0.153 10 D 0.845,1.142 0.845,1.575 false

Connect the connectors to the front seat outer belt assembly LH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTCs B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Outer Belt Assembly LH
*2 Airbag Sensor Assembly



OK

NG