Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2015.11–2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1860/64  Short in Driver Side Knee Airbag Squib Circuit  B1861/64  Open in Driver Side Knee Airbag Squib Circuit  B1862/64  Short to GND in Driver Side Knee Airbag Squib Circuit  B1863/64  Short to B+ in Driver Side Knee Airbag Squib Circuit  


DESCRIPTION

The driver side knee airbag squib circuit consists of the airbag sensor assembly and lower No. 1 instrument panel airbag assembly.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side knee airbag squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1860/64
·

The airbag sensor assembly receives a line short circuit signal in the driver side knee airbag squib circuit during primary check.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Lower No. 1 instrument panel airbag assembly (Driver side knee airbag squib)

·

Airbag sensor assembly


B1861/64
·

The airbag sensor assembly receives an open circuit signal in the driver side knee airbag squib circuit.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


B1862/64
·

The airbag sensor assembly receives a short circuit to ground signal in the driver side knee airbag squib circuit.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


B1863/64
·

The airbag sensor assembly receives a short circuit to B+ signal in the driver side knee airbag squib circuit.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction



WIRING DIAGRAM

C249389E07
0.698,2.479 0.979,2.646 0.281,0.167 10 false G23 0.698,2.656 3.615,3.104 2.917,0.448 10 false Lower No. 1 Instrument Panel Airbag Assembly (Driver Side Knee Airbag Squib) 4.646,3.01 5.01,3.156 0.365,0.146 10 false G18 4.698,1.99 5.083,2.156 0.385,0.167 10 false DK- 4.479,1.906 4.646,2.073 0.167,0.167 10 false 10 4.698,1.146 5.198,1.313 0.5,0.167 10 false DK+ 2.042,1.906 2.563,2.073 0.521,0.167 10 false DK- 2.042,1.063 2.5,1.229 0.458,0.167 10 false DK+ 4.531,1.063 4.646,1.229 0.115,0.167 10 false 9 2.406,1.906 2.521,2.073 0.115,0.167 10 false 2 2.406,1.063 2.521,1.229 0.115,0.167 10 false 1 4.646,3.188 6.281,3.365 1.635,0.177 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C238350E04
0.637,0.869 0.758,1.022 0.121,0.153 10 D 1.044,0.869 1.164,1.022 0.121,0.153 10 C 1.622,0.869 1.743,1.022 0.121,0.153 10 B 2.025,0.869 2.146,1.022 0.121,0.153 10 A 2.47,1.184 2.646,1.360 0.177,0.175 10 *2 0.45,1.656 0.602,1.808 0.152,0.152 10 *1 0.526,1.016 0.526,1.639 false 1.638,0.37 1.790,0.522 0.152,0.152 10 *3 1.387,0.884 1.387,0.46 1.387,0.46 1.613,0.46 false

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the lower No. 1 instrument panel airbag assembly and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the lower No. 1 instrument panel airbag assembly and airbag sensor assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the instrument panel wire connector (on the lower No. 1 instrument panel airbag assembly side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short spring for the instrument panel wire with the activation prevention mechanism are not deformed or damaged.

OK:

The short spring is not deformed or damaged.


Text in Illustration
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire



OK

2.CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB)

NG

REPLACE INSTRUMENT PANEL WIRE

2.CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB)
a.
U159440E03
0.719,0.698 0.719,1.094 false 1.854,2.229 2.031,2.229 false 0.656,1.125 0.813,1.292 0.156,0.167 10 false *1 2.281,0.792 2.448,0.958 0.167,0.167 10 false *2 1.823,0.563 1.99,0.729 0.167,0.167 10 false A 1.677,0.563 1.844,0.729 0.167,0.167 10 false B 1.156,0.573 1.323,0.74 0.167,0.167 10 false C 0.813,0.573 0.979,0.74 0.167,0.167 10 false D 2.052,2.146 2.365,2.313 0.313,0.167 10 false SST 0.354,1.844 0.51,2.01 0.156,0.167 10 false *a 0.5,2.271 0.792,2.427 0.292,0.156 10 false G23

Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the lower No. 1 instrument panel airbag assembly (driver side knee airbag squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1860/64, B1861/64, B1862/64 or B1863/64 is not output.


HINT:

Codes other than DTCs B1860/64, B1861/64, B1862/64 and B1863/64 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.

Text in Illustration
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly)



OK

REPLACE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

NG

3.CHECK INSTRUMENT PANEL WIRE
3.CHECK INSTRUMENT PANEL WIRE
a.
U159441E03
0.677,0.708 0.677,1.104 false 1.448,2.188 1.729,2.188 false 0.948,2.188 1.219,2.188 false 1.406,0.552 1.406,0.177 1.406,0.177 1.167,0.177 false 0.615,1.104 0.771,1.271 0.156,0.167 10 false *1 2.281,0.813 2.448,0.979 0.167,0.167 10 false *2 1.885,0.531 2.052,0.698 0.167,0.167 10 false A 1.583,0.552 1.75,0.719 0.167,0.167 10 false B 1.125,0.563 1.292,0.729 0.167,0.167 10 false C 0.823,0.552 0.99,0.719 0.167,0.167 10 false D 1.792,2.115 2.104,2.281 0.313,0.167 10 false DK- 0.625,2.115 0.938,2.281 0.313,0.167 10 false DK+ 0.26,1.781 0.417,1.948 0.156,0.167 10 false *a 0.99,0.125 1.146,0.292 0.156,0.167 10 false *3 0.49,2.51 0.958,2.74 0.469,0.229 10 false G23

Disconnect the instrument panel wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G23-1 (DK+) - Body ground Power switch on (IG) Below 1 V
G23-2 (DK-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G23-1 (DK+) - G23-2 (DK-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G23-1 (DK+) - Body ground Always 1 MΩ or higher
G23-2 (DK-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G23-1 (DK+) - G23-2 (DK-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly)




OK

4.CHECK DTC

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK DTC
a.
C238353E01
0.914,0.646 1.035,0.799 0.121,0.153 10 D 1.077,0.646 1.197,0.799 0.121,0.153 10 C 1.584,0.646 1.704,0.799 0.121,0.153 10 B 1.736,0.646 1.857,0.799 0.121,0.153 10 A 2.171,0.952 2.348,1.128 0.177,0.175 10 *2 0.734,1.224 0.886,1.400 0.152,0.175 10 *1 0.816,0.799 0.816,1.213 false

Connect the connectors to the lower No. 1 instrument panel airbag assembly and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1860/64, B1861/64, B1862/64 or B1863/64 is not output.


HINT:

Codes other than DTCs B1860/64, B1861/64, B1862/64 and B1863/64 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly



OK

NG