The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH and curtain shield airbag assembly RH) is composed of the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.
The side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.
These DTCs are stored when a malfunction is detected for the side collision sensor RH circuit.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1622/81
B1623/81 B1632/81 B1633/81 B1642/81 |
·
The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor RH circuit. ·
Side airbag sensor assembly RH malfunction ·
Side No. 2 airbag sensor assembly RH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Side airbag sensor assembly RH ·
Side No. 2 airbag sensor assembly RH ·
Airbag sensor assembly |
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Check for current DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| Current DTC B1642 or 81 is output. | A |
| Current DTC B1623 is output. | B |
| Current DTC B1632 or B1633 is output. | C |
| Current DTC B1622 is output. | D |
| Current DTCs B1622, B1623, B1632, B1633, B1642 and 81 are not output. | E |
DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then on (IG) again.
Codes other than current DTCs B1622, B1623, B1632, B1633, B1642 and 81 may be output at this time, but they are not related to this check.
A
B
C
D
E
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.
The connectors are properly connected.
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.
Check that the terminals of the connectors are not damaged.
The terminals are not deformed or damaged.
OK
NG
Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-4 (BBR+) - M25-3 (BBR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-4 (BBR+) - M25-3 (BBR-) | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-4 (BBR+) - Body ground | Power switch on (IG) | Below 1 V |
| M25-3 (BBR-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| M25-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-1 (BCR+) - M25-2 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-1 (BCR+) - M25-2 (BCR-) | Always | 1 MΩ or higher |
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-1 (BCR+) - Body ground | Power switch on (IG) | Below 1 V |
| M25-2 (BCR-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| M25-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Connect the connectors to the side No. 2 airbag sensor assembly RH and airbag sensor assembly.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1642 or 81 is output. | A |
| DTC B1647 or 82 is output. | B |
| DTCs B1642, B1647, 81 and 82 are not output. | C |
Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
A
B
C
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs B1642, B1647, 81 and 82 are not output. | A |
| DTC B1642 or 81 is output. | B |
| DTC B1647 or 82 is output. | C |
Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly RH |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Check for history DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| History DTC B1622 is not output. | A |
| History DTC B1622 is output. | B |
Codes other than history DTC B1622 may be output at this time, but they are not related to this check.
A
B
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly and side airbag sensor assembly RH.
The connectors are properly connected.
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag sensor assembly and side airbag sensor assembly RH.
Check that the terminals of the connectors are not damaged.
The terminals are not deformed or damaged.
OK
NG
Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-4 (BBR+) - M25-3 (BBR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-4 (BBR+) - M25-3 (BBR-) | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-4 (BBR+) - Body ground | Power switch on (IG) | Below 1 V |
| M25-3 (BBR-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| M25-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Connect the connector to the airbag sensor assembly.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs B1623 and B1628 are not output. | A |
| DTC B1623 is output. | B |
| DTC B1628 is output. | C |
Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.
The connectors are properly connected.
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.
Check that the terminals of the connectors are not damaged.
The terminals are not deformed or damaged.
OK
NG
Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-1 (BCR+) - M25-2 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-1 (BCR+) - M25-2 (BCR-) | Always | 1 MΩ or higher |
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-1 (BCR+) - Body ground | Power switch on (IG) | Below 1 V |
| M25-2 (BCR-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M25-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| M25-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Connect the connector to the side No. 2 airbag sensor assembly RH.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1632 or B1633 is output. | A |
| DTC B1637 or B1638 is output. | B |
| DTCs B1632, B1633, B1637 and B1638 are not output. | C |
Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
A
B
C
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs B1632, B1633, B1637 and B1638 are not output. | A |
| DTC B1632 or B1633 is output. | B |
| DTC B1637 or B1638 is output. | C |
Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly RH |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs B1622 and B1627 are not output. | A |
| DTC B1622 is output. | B |
| DTC B1627 is output. | C |
Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C