Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY(w/o Occupant Classification System) › from 2015.11
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278104 CURTAIN SHIELD AIRBAG ASSEMBLY(w/o Occupant Classification System) A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY(w/o Occupant Classification System)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 62180A 1.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B296251E02
0.5,0.865 0.26,0.865 true 0.083,0.771 0.292,0.958 0.208,0.188 10 true (A)

Temporarily install the curtain shield airbag assembly with the 3 hooks as shown in the illustration.


d.

Engage the hook (A).

NOTICE:
·

When installing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.

·

Do not twist the curtain shield airbag assembly when installing it.




e.

Install the curtain shield airbag assembly to the body panel with a new bolt, the 4 clips, 7 new clips and 3 new spacers in the order shown in the illustration.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)

B296249E02
5.552,1.552 5.333,1.333 5.333,1.333 5.292,1.333 true 5.396,1.802 5.104,1.802 true 5.313,2.031 5.26,1.979 5.26,1.979 5.063,1.979 true 5.302,2.177 5.26,2.229 5.26,2.229 5.073,2.229 true 5.448,2.125 5.167,2.417 5.167,2.417 5.031,2.417 false 1.25,1.344 1.458,1.135 1.458,1.135 1.51,1.135 true 1.417,1.583 1.708,1.583 true 1.51,1.813 1.563,1.76 1.563,1.76 1.76,1.76 true 1.521,1.969 1.563,2.01 1.563,2.01 1.75,2.01 true 1.375,1.927 1.656,2.208 1.656,2.208 1.781,2.208 true 5.125,1.271 5.281,1.438 0.156,0.167 10 false *1 4.958,1.729 5.115,1.896 0.156,0.167 10 false *2 4.906,1.885 5.063,2.052 0.156,0.167 10 false *3 4.917,2.125 5.073,2.292 0.156,0.167 10 false *4 4.896,2.354 5.052,2.521 0.156,0.167 10 false *5 3.49,0.26 3.594,0.417 0.104,0.156 10 true 1 1.938,0.417 2.042,0.573 0.104,0.156 10 true 2 1.396,0.51 1.5,0.667 0.104,0.156 10 true 3 1.031,0.49 1.135,0.646 0.104,0.156 10 true 4 0.552,0.563 0.656,0.719 0.104,0.156 10 true 5 4.063,0.354 4.167,0.51 0.104,0.156 10 true 6 4.646,0.365 4.75,0.521 0.104,0.156 10 true 7 5.156,0.563 5.26,0.719 0.104,0.156 10 true 8 5.635,0.625 5.74,0.781 0.104,0.156 10 true 9 5.844,0.865 6.021,1.021 0.177,0.156 10 true 10 6.656,1.281 6.833,1.438 0.177,0.156 10 true 11 2.406,0.188 2.583,0.344 0.177,0.156 10 true 12 1.552,1.073 1.708,1.24 0.156,0.167 10 false *1 1.729,1.51 1.885,1.677 0.156,0.167 10 false *2 1.771,1.698 1.927,1.865 0.156,0.167 10 false *3 1.76,1.927 1.917,2.094 0.156,0.167 10 false *4 1.792,2.135 1.948,2.302 0.156,0.167 10 false *5

Text in Illustration
*1 Pin *2 Clip
*3 Curtain Shield Airbag Assembly *4 Body Panel
*5 Spacer - -


f.

Push in 7 new pins to each clip.

NOTICE:

Make sure that the pins of the clips are pushed in firmly.



g.
B296246E02
1.656,1.823 1.271,1.823 true 1.469,0.167 1.208,0.167 1.208,0.167 1.042,0.333 true 1.115,1.74 1.271,1.917 0.156,0.177 10 true *1 1.51,0.094 1.667,0.271 0.156,0.177 10 false *2

Connect the curtain shield airbag connector.

Text in Illustration
*1 Airbag Connector
*2 Airbag Connector Lock

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



h.

Push in the airbag connector lock to install the curtain shield airbag connector.


Hide 2.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.INSTALL ROOF HEADLINING ASSEMBLY