1.INSTALL ROOF HEADLINING ASSEMBLY
Pull the roof headlining back into the vehicle through the back door.
Do not damage the roof headlining assembly or vehicle interior.
Engage the 2 claws.
Install the roof headlining assembly with the 3 clips.
for front pillar RH side:
Engage the 3 clamps.
Connect the connector.
for front pillar LH side:
Engage the 3 clamps.
Connect the connector.
for rear pillar RH side:
Engage the 2 clamps.
Connect the connector bracket with the bolt.
Connect the connector.
74348
2.INSTALL VISOR HOLDER
Engage the 2 claws and turn the visor holder 45° counterclockwise to install it.
Use the same procedure for the RH side and LH side.
74320
3.INSTALL VISOR ASSEMBLY LH
Install the visor assembly LH with the 2 screws.
Install the visor assembly LH with the arrow facing the front of the vehicle.
Connect the visor shaft into the visor holder.
74310
4.INSTALL VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74610S
5.INSTALL ASSIST GRIP ASSEMBLY
Use the same procedure to install all assist grips.
Assemble the front assist grip assembly as shown in the illustration.
Install the assist grip assembly.
81260A
6.INSTALL MAP LIGHT ASSEMBLY
81240
7.INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/ Room Light)
62472A
8.INSTALL ROOF SIDE INNER GARNISH LH
Pass the floor anchor of the rear seat 3 point type outer belt assembly LH through the roof side inner garnish LH.
Engage the 5 clips to install the roof side inner garnish LH.
64740C
9.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
Engage the guide, 4 claws and 4 clips.
| *a | Rear Seatback Hinge | - | - |
Install the deck trim side panel assembly LH with the bolt and 2 screws.
Turn the rear seatback hinge as shown in the illustration.
58732C
10.INSTALL REAR ABSORBER CAP LH
Engage the 2 guides and 2 claws to install the rear absorber cap LH.
81330
11.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
73370
12.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
62471A
13.INSTALL ROOF SIDE INNER GARNISH RH
Pass the floor anchor of the rear seat 3 point type outer belt assembly RH through the roof side inner garnish RH.
Engage the 5 clips to install the roof side inner garnish RH.
Engage the guide and 4 claws to connect the belt guide.
73350
14.CONNECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY
64730B
15.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
Use the same procedure as for the LH side.
58731C
16.INSTALL REAR ABSORBER CAP RH
Use the same procedure as for the LH side.
73360
17.INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
64716D
18.INSTALL REAR DECK TRIM COVER
Engage the 2 guides and 4 claws.
Install the rear deck trim cover with the 2 clips.
64330D
19.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
Install the package tray trim panel assembly.
64997
20.INSTALL DECK FLOOR BOX LH
Install the deck floor box LH.
64995
21.INSTALL DECK FLOOR BOX RH
Use the same procedure as for the LH side.
58410B
22.INSTALL DECK BOARD ASSEMBLY
Install the deck board assembly.
62412B
23.INSTALL CENTER PILLAR UPPER GARNISH LH
Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH.
Engage the clip.
Install the center pillar upper garnish LH with the 2 screws.
62414A
24.INSTALL CENTER PILLAR LOWER GARNISH LH
Engage the 4 claws and 2 clips to install the center pillar lower garnish LH.
73220
25.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
73233C
26.INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)
62332A
27.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Align the alignment mark (White) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
| *a | Alignment Mark (White) |
| *b | Flange Position |
After installation, check that the corners fit correctly.
62212
28.INSTALL FRONT PILLAR GARNISH LH
Remove the protective cover.
Make sure that the front pillar garnish clip is not damaged.
If there is any damage, replace the garnish clip with a new one.
Push the front pillar garnish LH in the direction indicated by the arrow (1) shown in the illustration to engage the 2 guides.
| *a | Protective Tape |
Using needle-nose pliers with the tips wrapped with protective tape, bend the end of the front pillar garnish clip in the direction indicated by the arrow (2) shown in the illustration.
Push the front pillar garnish LH in the direction indicated by the arrow (3) shown in the illustration and insert it to the front pillar garnish clip.
Using needle-nose pliers with the tips wrapped with protective tape, rotate the front pillar garnish clip in the direction indicated by the arrow (4) shown in the illustration.
Rotate the front pillar garnish clip so that the longer end of the front pillar garnish clip is positioned at the bottom.
Using needle-nose pliers with the tips wrapped with protective tape, push the front pillar garnish clip in the direction indicated by the arrow (5) and rotate it to the position shown in the illustration.
Make sure that the front pillar garnish clip is positioned as shown in the illustration. Failing to do so may cause a gap between the front pillar garnish LH and roof headlining assembly.
Engage the clip and front pillar garnish clip to install the front pillar garnish LH.
| *1 | Front Pillar Garnish Clip |
If there is a gap between the front pillar garnish LH and roof headlining assembly, the front pillar garnish clip is not installed correctly. While lightly pressing the front pillar garnish LH as shown in the illustration, push it towards the front pillar garnish clip side.
Make sure that the curtain shield airbag assembly LH is not pinched.
62312B
29.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Align the alignment mark (Yellow) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
| *a | Alignment Mark (Yellow) |
| *b | Flange Position |
After installation, check that the corners fit correctly.
62112
30.INSTALL COWL SIDE TRIM BOARD LH
Engage the clip.
Install the cowl side trim board with the clip.
67914
31.INSTALL FRONT DOOR SCUFF PLATE LH
Engage the 8 claws to install the front door scuff plate.
67918A
32.INSTALL REAR DOOR SCUFF PLATE LH
Engage the guide and the 5 claws to install the rear door scuff plate.
62411B
33.INSTALL CENTER PILLAR UPPER GARNISH RH
Use the same procedure as for the LH side.
62413A
34.INSTALL CENTER PILLAR LOWER GARNISH RH
Use the same procedure as for the LH side.
73210
35.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
73233
36.INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)
Use the same procedure as for the LH side.
62331A
37.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Align the alignment mark (Red) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
| *a | Alignment Mark (Red) |
| *b | Flange Position |
After installation, check that the corners fit correctly.
62211
38.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
67917A
39.INSTALL REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
62311B
40.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Align the alignment mark (Yellow green) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
| *a | Alignment Mark (Yellow green) |
| *b | Flange Position |
After installation, check that the corners fit correctly.
62111C
41.INSTALL COWL SIDE TRIM BOARD RH
Use the same procedure as for the LH side.
67913
42.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
43.INSTALL REAR SEAT ASSEMBLY (for Separate Type Seatback)
44.INSTALL REAR SEAT ASSEMBLY (for Bench Type Seatback)