Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM (w/o Occupant Classification System) › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057041 SEAT BELT _0278116 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

The combination meter assembly blinks or turns off the seat belt warning light on the combination meter assembly in accordance with the state of the front seat inner belt assembly (for driver).

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


WIRING DIAGRAM

B287218E45
0.844,0.823 1.281,1.094 0.438,0.271 10 false CAN 2.063,0.833 2.49,1.063 0.427,0.229 10 false CAN 4.177,0.823 4.51,1.063 0.333,0.24 10 false 3D 4.198,0.646 4.469,0.844 0.271,0.198 10 false 34 2.677,0.833 3.115,1.063 0.438,0.229 10 false DBKL 0.094,1.563 1.281,2.031 1.188,0.469 10 false Combination Meter Assembly 0.563,2.448 2.354,2.625 1.792,0.177 10 false : CAN Communication Line 1.708,1.531 2.042,1.719 0.333,0.188 10 false MB 3.125,0.74 3.406,1.042 0.281,0.302 10 false 18 5.281,0.74 5.531,0.979 0.25,0.24 10 false 3 6.104,0.74 6.313,0.958 0.208,0.219 10 false 2 1.708,1.677 3.344,2.094 1.635,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 5.167,1.094 6.104,1.344 0.938,0.25 10 false M10*1, M8*2 5.167,1.25 6.49,1.688 1.323,0.438 10 false Front Seat Inner Belt Assembly (for Driver) 3.5,1.25 4.573,1.719 1.073,0.469 10 false Instrument Panel Junction Block Assembly 4.177,2.302 5.198,2.792 1.021,0.49 10 false *1: for LHD 5.521,2.302 6.542,2.792 1.021,0.49 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/o Occupant Classification System)>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Seat Buckle SW Driver seat belt buckle switch signal/ON or OFF ON: Driver seat belt fastened
OFF: Driver seat belt unfastened
-

OK:

ON or OFF appears on the tester screen according to the driver seat belt condition.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER)
2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER)
a.
B271232E04
0.205,0.166 0.357,0.303 0.151,0.137 10 *a

Remove the front seat inner belt assembly (for driver) (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 3 Driver seat belt unfastened Below 1 Ω
2 - 3 Driver seat belt fastened 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Front Seat Inner Belt Assembly (for Driver))



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER)

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U183440E01
0.164,0.092 0.333,0.262 0.170,0.170 10 *a 1.957,0.621 2.210,0.770 0.253,0.149 10 MB 5.628,0.404 5.881,0.553 0.253,0.149 10 3D 1.691,1.521 2.083,1.684 0.392,0.163 10 DBKL 2.258,1.115 2.258,1.581 2.258,1.581 2.059,1.581 false

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


b.

Disconnect the 3D instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-18 (DBKL) - 3D-34 Always Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT SEAT INNER BELT ASSEMBLY - BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT SEAT INNER BELT ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
3D-34 - M10-3 Always Below 1 Ω
M10-3 - Body ground Always 10 kΩ or higher
M10-2 - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
3D-34 - M8-3 Always Below 1 Ω
M8-3 - Body ground Always 10 kΩ or higher
M8-2 - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR