Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM (w/o Occupant Classification System) › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057041 SEAT BELT _0278116 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Front Passenger Side Seat Belt Warning Light Malfunction  


DESCRIPTION

The occupant detection sensor (separate type front seat cushion pad) detects if the front passenger seat is occupied and sends signals to the combination meter assembly. The front seat inner belt assembly (for front passenger) detects the front passenger seat belt condition and sends signals to the combination meter assembly. After receiving the signals from the occupant detection sensor (separate type front seat cushion pad) and front seat inner belt assembly (for front passenger), the seat belt warning light on the combination meter assembly will blink or go off.

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


WIRING DIAGRAM

B275873E06
0.527,1.984 1.727,2.288 1.200,0.304 10 Combination Meter Assembly 2.729,1.86 4.462,2.333 1.732,0.473 10 Occupant Detection Sensor (Separate Type Front Seat Cushion Pad) 4.565,1.153 5.873,1.626 1.309,0.473 10 Front Seat Inner Belt Assembly (for Front Passenger) 0.527,1.855 0.800,1.991 0.272,0.137 10 G1 1.304,0.782 1.556,0.919 0.251,0.137 10 SW 1.647,0.684 1.819,0.821 0.172,0.137 10 12 2.684,0.6 2.783,0.737 0.099,0.137 10 3 2.325,0.6 2.423,0.737 0.099,0.137 10 3 2.297,0.988 2.451,1.124 0.154,0.137 10 *1 2.661,0.988 2.815,1.124 0.154,0.137 10 *2 6.029,0.988 6.183,1.124 0.154,0.137 10 *1 5.659,0.988 5.813,1.124 0.154,0.137 10 *2 6.181,2.028 6.891,2.165 0.710,0.137 10 *1: for LHD 6.181,2.28 6.908,2.417 0.727,0.137 10 *2: for RHD 2.794,1.154 2.893,1.290 0.099,0.137 10 1 3.061,1.154 3.170,1.290 0.110,0.137 10 B 3.779,1.154 3.878,1.290 0.099,0.137 10 3 4.046,1.154 4.156,1.290 0.110,0.137 10 B 2.626,0.792 2.890,0.929 0.265,0.137 10 M9 2.225,0.792 2.514,0.929 0.289,0.137 10 M11 5.957,0.792 6.246,0.929 0.289,0.137 10 M11 5.619,0.792 5.884,0.929 0.265,0.137 10 M9 5.679,0.6 5.778,0.737 0.099,0.137 10 2 6.053,0.6 6.152,0.737 0.099,0.137 10 2

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P-Seatbelt Buckle SW Front passenger seat belt buckle switch signal/ON or OFF ON: Front passenger seat belt unfastened
OFF: Front passenger seat belt fastened
Front passenger seat occupied

OK:

ON or OFF appears on the tester screen according to the front passenger seat belt condition.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FRONT SEAT INNER BELT - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FRONT SEAT INNER BELT - BODY GROUND)
a.

Disconnect the G1 combination meter assembly connector.


b.

Disconnect the M11*1 or M9*2 front seat inner belt assembly (for front passenger) connector.


c.

Measure the resistance according to the value(s) in the table below.

*1: for LHD

*2: for RHD


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G1-12 (SW) - M11-3 Always Below 1 Ω
G1-12 (SW) - Body ground Always 10 kΩ or higher
M11-2 - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
G1-12 (SW) - M9-3 Always Below 1 Ω
G1-12 (SW) - Body ground Always 10 kΩ or higher
M9-2 - Body ground Always Below 1 Ω




OK

3.INSPECT OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)
a.
B218574E01
0.146,0.125 0.303,0.276 0.157,0.151 10 *a

Remove the occupant detection sensor (separate type front seat cushion pad) (See page Vehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 3 Front passenger seat occupied Below 100 Ω
1 - 3 Front passenger seat not occupied 1 MΩ or higher


Text in Illustration
*a Component without harness connected
(Occupant Detection Sensor (Separate Type Front Seat Cushion Pad))



OK

4.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER)

NG

REPLACE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)

4.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER)
a.
U183387E02
0.177,0.104 0.417,0.313 0.24,0.208 10 false *a 1.604,0.688 1.802,0.844 0.198,0.156 10 false *A 2.375,0.688 2.583,0.854 0.208,0.167 10 false *B 1.24,0.677 1.573,0.865 0.333,0.188 10 false M11 2.031,0.677 2.333,0.844 0.302,0.167 10 false M9 1.677,2.917 1.854,3.083 0.177,0.167 10 false B

Remove the front seat inner belt assembly (for front passenger) (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
M11-3 - B-1 Always Below 1 Ω
M11-2 - B-3 Front passenger seat belt unfastened Below 1 Ω
M11-2 - B-3 Front passenger seat belt fastened 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
M9-3 - B-1 Always Below 1 Ω
M9-2 - B-3 Front passenger seat belt unfastened Below 1 Ω
M9-2 - B-3 Front passenger seat belt fastened 10 kΩ or higher


Text in Illustration
*A for LHD
*B for RHD
*a Component without harness connected
(Front Seat Inner Belt Assembly (for Front Passenger))



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER)