Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY
RM2170E _58 Vehicle Interior _057041 SEAT BELT _0278118 FRONT SEAT OUTER BELT ASSEMBLY N

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


HINT:

When scrapping vehicles equipped with a seat belt pretensioner or disposing of a seat belt (with a seat belt pretensioner), always deploy the procedures described below. If any abnormality occurs during deployment of the seat belt pretensioner, contact the service dept. of the distributor.


PROCEDURE

Hide 73220 1.DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (When Installed in Vehicle)

CAUTION:
·

Use gloves and safety glasses when handling a seat belt with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a seat belt with a deployed pretensioner.

·

When deploying a seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical interference.

·

When disposing of a seat belt with a pretensioner, never deploy the pretensioner in the customer's vehicle.



NOTICE:
·

Never dispose of a seat belt with a pretensioner that has not been deployed.

·

The seat belt produces an exploding sound when the pretensioner deploys, so perform the operation outdoors where it will not disturb local residents.

·

When deploying a seat belt pretensioner, perform the operation at least 10 m (33 ft.) away from the seat belt.

·

Be sure to follow the procedure listed below when deploying a seat belt pretensioner.



a.
B104819E23
2.406,0.365 2.292,0.708 false 2.094,0.729 2.427,0.927 0.333,0.198 10 false SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying a seat belt pretensioner, always use the specified SST.


i.
B104820E31
1.906,1.302 1.969,1.667 false 2.51,0.771 2.74,0.771 false 2.75,0.667 2.896,0.885 0.146,0.219 10 false *1 1.813,1.688 2.208,1.885 0.396,0.198 10 false SST

Connect the red clip of SST to the 12 V battery positive (+) terminal and the black clip to the 12 V battery negative (-) terminal.

Text in Illustration
*1 12 V Battery

HINT:

At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.



ii.
B104821E11
2.417,1.594 2.469,1.75 false 2.313,1.74 2.646,1.938 0.333,0.198 10 false SST

Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

CAUTION:

If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.




b.

Disconnect the seat belt pretensioner connector.


ii.

Disconnect the cable from the negative (-) auxiliary battery terminal.


iii.

for LH Side:

Remove the front floor cover LH (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Type Seatback)>REMOVAL).


iv.

Remove the front door scuff plate (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


v.

Remove the rear door scuff plate (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


vi.

Disconnect the front door opening trim weatherstrip (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


vii.

Disconnect the rear door opening trim weatherstrip (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


viii.

Remove the center pillar lower garnish (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


ix.
B307778E01
1.344,3.035 1.521,3.238 0.177,0.203 10 *1 0.999,3.196 1.329,3.125 false

Using a screwdriver, pull out the locking button in the direction shown by the arrow in the illustration to release the lock, and disconnect the pretensioner connector as shown in the illustration.

Text in Illustration
*1 Protective Tape

HINT:

Tape the screwdriver tip before use.




c.
B221509E01
1.999,1.678 2.289,1.820 0.290,0.142 10 SST 0.831,1.473 1.121,1.614 0.290,0.142 10 SST 1.982,1.764 1.788,1.764 false 1.007,1.473 1.007,1.306 false

Connect SST.

i.

Connect 2 SST, and then connect them to the seat belt pretensioner.

SST
09082-00700  
09082-00770  

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.



ii.
U110719E07
2.594,0.844 2.594,1.802 false 0.875,1.688 0.875,1.896 false 0.917,1.74 2.542,1.74 false 0.5,1.156 0.677,1.406 false 1.625,1.781 1.99,2.052 0.365,0.271 10 false *a 0.198,1.052 0.708,1.323 0.51,0.271 10 false SST

Move SST at least 10 m (33 ft.) away from the front of the vehicle.

Text in Illustration
*a 10 m or more


iii.

Close the doors and windows of the vehicle.

NOTICE:

Do not damage the SST wire harness.




d.

Deploy the seat belt pretensioner.

i.

Confirm that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.


ii.

Connect the red clip of SST to the 12 V battery positive (+) terminal and the black clip to the 12 V battery negative (-) terminal.


iii.

Press the SST deployment switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.




e.

Dispose of the seat belt.

i.

Remove the seat belt and SST


ii.
B221506

Place the seat belt in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

CAUTION:
·

The seat belt becomes very hot when the pretensioner is deployed, so leave it untouched for at least 30 minutes after the pretensioner is deployed.

·

Use gloves and safety glasses when handling a seat belt with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a seat belt with a deployed pretensioner.



HINT:

When scrapping a vehicle, deploy the seat belt pretensioner, and then scrap the vehicle with the seat belt installed.




Hide 73220 2.DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (When Not Installed in Vehicle)

CAUTION:
·

Use gloves and safety glasses when handling a seat belt with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a seat belt with a deployed pretensioner.

·

When deploying a seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical interference.

·

When disposing of a seat belt with a pretensioner, never deploy the pretensioner in the customer's vehicle.



NOTICE:
·

Never dispose of a seat belt with a pretensioner that has not been deployed.

·

The seat belt produces an exploding sound when the pretensioner deploys, so perform the operation outdoors where it will not disturb local residents.

·

When deploying a seat belt pretensioner, perform the operation at least 10 m (33 ft.) away from the seat belt.

·

Be sure to follow the procedure listed below when deploying a seat belt pretensioner.




b.
B297202E03
1.625,0.552 1.344,0.552 false 2.417,0.656 2.615,0.875 0.198,0.219 10 false *b 1.177,0.469 1.385,0.708 0.208,0.24 10 false *a

Wind the seat belt webbing with the retractor.

Text in Illustration
*a Cut
*b 100 mm


c.

When the seat belt webbing is sufficiently wound, cut the seat belt webbing approximately 100 mm (3.94 in.) from the retractor, as shown in the illustration.

HINT:

The retractor resistance increases in correlation with how much the seat belt webbing is wound.



d.
B104819E23
2.406,0.365 2.292,0.708 false 2.094,0.729 2.427,0.927 0.333,0.198 10 false SST

Check whether SST is functioning.

SST
09082-00700  

CAUTION:

When deploying a seat belt pretensioner, always use the specified SST.


i.
B104820E31
1.906,1.302 1.969,1.667 false 2.51,0.771 2.74,0.771 false 2.75,0.667 2.896,0.885 0.146,0.219 10 false *1 1.813,1.688 2.208,1.885 0.396,0.198 10 false SST

Connect the red clip of SST to the 12 V battery positive (+) terminal and the black clip to the 12 V battery negative (-) terminal.

Text in Illustration
*1 12 V Battery

HINT:

At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.



ii.
B104821E11
2.417,1.594 2.469,1.75 false 2.313,1.74 2.646,1.938 0.333,0.198 10 false SST

Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

CAUTION:

If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST




e.
B221509E01
1.999,1.678 2.289,1.820 0.290,0.142 10 SST 0.831,1.473 1.121,1.614 0.290,0.142 10 SST 1.982,1.764 1.788,1.764 false 1.007,1.473 1.007,1.306 false

Connect SST.

i.

Connect 2 SST, and then connect them to the seat belt pretensioner.

SST
09082-00700  
09082-00770  

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.



ii.
B279626E04
2.563,1.125 2.74,0.99 false 2.073,1.427 1.938,1.427 false 2.281,1.052 2.667,1.26 0.385,0.208 10 false SST 2.094,1.344 2.479,1.552 0.385,0.208 10 false SST

Place the seat belt on the ground and cover it with a tire and wheel assembly.

NOTICE:
·

Position the seat belt as shown in the illustration.

·

Use a scrap tire and wheel assembly when disposing of a seat belt pretensioner.




iii.

Position and hold SST at least 10 m (33 ft.) away from the wheel.

NOTICE:

Do not damage the SST wire harness.




f.
B282678E02
0.618,4.221 0.940,4.387 0.322,0.166 10 SST 0.659,4.113 0.767,4.221 false 2.089,3.936 2.270,4.100 0.181,0.163 10 *a 1.659,1.097 1.97,1.001 false 1.981,0.906 2.911,1.168 0.930,0.263 10 *1

Deploy the seat belt pretensioner.

Text in Illustration
*1 12 V Battery
*a 10 m or more

i.

Check that no one is within a 10 m (33 ft.) radius of the wheel.


ii.

Connect the red clip of SST to the 12 V battery positive (+) terminal and the black clip to the 12 V battery negative (-) terminal.


iii.

Press the SST deployment switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.




g.
B282679E01
2.102,0.638 2.417,0.499 false 2.423,0.408 2.582,0.566 0.159,0.159 10 *1

Dispose of the seat belt.

Text in Illustration
*1 Plastic Bag

i.

Remove the wheel and SST.


ii.

Place the seat belt in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

CAUTION:
·

The seat belt becomes very hot when the pretensioner is deployed, so leave it untouched for at least 30 minutes after the pretensioner is deployed.

·

Use gloves and safety glasses when handling a seat belt with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a seat belt with a deployed pretensioner.



HINT:

When scrapping a vehicle, deploy the seat belt pretensioner, and then scrap the vehicle with the seat belt installed.