Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278125 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1442/42  Air Inlet Damper Control Servo Motor Circuit  


DESCRIPTION

The No. 1 blower damper servo sub-assembly (air inlet) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal, reverse) based on the signals to move the air inlet mode selection No. 1 blower damper servo sub-assembly (air inlet) to any position, which controls the intake air settings (FRESH, FRESH/RECIRCULATION, and RECIRCULATION).

The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

HINT:

Confirm that no mechanical problem is present because this diagnostic code can be stored when either a damper link or the damper is mechanically locked.


DTC No. DTC Detection Condition Trouble Area
B1442/42 Air inlet damper position sensor value does not change even though air conditioning amplifier assembly operates No. 1 blower damper servo sub-assembly (air inlet).
·

No. 1 blower damper servo sub-assembly (air inlet)

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E229253E02
5.728,2.187 5.825,2.362 0.097,0.174 10 3 5.728,1.235 5.825,1.409 0.097,0.174 10 4 5.948,2.281 6.404,2.456 0.456,0.174 10 BUS 5.948,3.237 6.404,3.412 0.456,0.174 10 BUS G 5.504,4.085 5.746,4.259 0.242,0.174 10 z1 5.504,4.243 7.089,4.575 1.585,0.332 10 Air Conditioning Amplifier Assembly 0.524,4.1 2.330,4.432 1.806,0.332 10 No. 1 Blower Damper Servo Sub-assembly (Air Inlet) 5.728,3.141 5.825,3.315 0.097,0.174 10 2 5.948,1.329 6.390,1.503 0.443,0.174 10 B BUS 3.006,4.085 4.561,4.466 1.555,0.382 10 Air Conditioning Harness Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Operate the R/F (Recirculation/Fresh) switch.


e.

Enter the following menus: Body / Air Conditioner / Data List.


f.

Check the value(s) by referring to the table below.


Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Air Inlet Damper Actual Pulse No. 1 blower damper servo sub-assembly (air inlet) actual pulse / Min.: 128, Max.: 383 RECIRCULATION: 287 (pulse)
FRESH: 254 (pulse)
-

OK:

The display is as specified in the normal condition column.


Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.


Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Air Inlet Damper Targ Pulse No. 1 blower damper servo sub-assembly (air inlet) pulse Min.: 128, Max.: 383 Operates between 254 and 287 pulses

OK:

Recirculation damper position changes in accordance with each control range.



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

3.REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET)
3.REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET)
a.

Replace the No. 1 blower damper servo sub-assembly (air inlet) (See page Vehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY).

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Result:
Result Proceed to
DTC B1442/42 is output A
DTC B1442/42 is not output B




A

4.REPLACE AIR CONDITIONING HARNESS ASSEMBLY

B

END (NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET) WAS DEFECTIVE)

4.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
a.

Replace the air conditioning harness assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>REMOVAL).

HINT:

Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Result:
Result Proceed to
DTC B1442/42 is output A
DTC B1442/42 is not output B




A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

END (AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)