Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278128 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

Make sure to select face mode and max cold before disconnecting the cable from the negative (-) auxiliary battery terminal.


Hide 2.RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55722C 4.REMOVE INNER COWL TOP TO COWL BRACE (for LHD)

Hide 55722C 5.REMOVE INNER COWL TOP TO COWL BRACE (for RHD)

Hide 55735B 6.REMOVE FRONT AIR SHUTTER SEAL (for LHD)

Hide 55735B 7.REMOVE FRONT AIR SHUTTER SEAL (for RHD)

Hide 55815E 8.REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)

Hide 55815E 9.REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)

Hide 55701J 10.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 11.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 88707 12.DISCONNECT SUCTION PIPE SUB-ASSEMBLY

a.
E234992

Remove the bolt and rotate the hook connector.


b.
E234993

Disconnect the suction pipe sub-assembly.


c.

Remove the O-ring from the suction pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 88706 13.DISCONNECT LIQUID PIPE SUB-ASSEMBLY

a.
E234994

Disconnect the liquid pipe sub-assembly.


b.

Remove the O-ring from the liquid pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 87246A 14.DISCONNECT HEATER WATER OUTLET HOSE A

a.
E234995

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water outlet hose A.

NOTICE:
·

Do not apply excessive force to the heater outlet water hose A.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87209 15.DISCONNECT WATER HOSE SUB-ASSEMBLY

a.
E234996

Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose sub-assembly.

NOTICE:
·

Do not apply excessive force to the water hose sub-assembly.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 55303B 16.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 17.REMOVE STEERING COLUMN ASSEMBLY

Hide 82141 19.DISCONNECT INSTRUMENT PANEL WIRE

Hide 82730 20.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD)

Hide 82730 21.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for RHD)

Hide 89650 22.REMOVE POWER STEERING ECU ASSEMBLY (for LHD)

Hide 89650 23.REMOVE POWER STEERING ECU ASSEMBLY (for RHD)

Hide 58510D 26.DISCONNECT FRONT FLOOR CARPET ASSEMBLY

a.

Turn back the front floor carpet assembly.


Hide 55306A 27.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for LHD)

a.
E249366E02
1,1.625 0.531,2.375 0.531,2.375 1.396,2.927 true 0.76,0.479 1.094,0.438 true 2.458,2.094 2.24,1.823 true 0.344,2.302 0.51,2.479 0.167,0.177 10 true *1 2.49,2.052 2.688,2.25 0.198,0.198 10 true *2 0.563,0.396 0.729,0.594 0.167,0.198 10 true *3

Disengage each clamp.

Text in Illustration
*1 Bolt
*2 Screw
*3 Nut


b.

Remove the 2 bolts, screw, nut and No. 1 instrument panel brace sub-assembly.


Hide 55306A 28.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for RHD)

a.
E245864E02
2.24,0.542 2.563,0.76 true 0.792,1.25 1.146,1.302 true 2.292,2.823 2.021,2.958 true 2.313,2.74 2.5,2.927 0.188,0.188 10 true *1 0.625,1.167 0.813,1.354 0.188,0.188 10 true *2 2.573,0.688 2.76,0.875 0.188,0.188 10 true *3

Disengage each clamp.

Text in Illustration
*1 Bolt
*2 Screw
*3 Nut


b.

Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.


Hide 82141 29.DISCONNECT INSTRUMENT PANEL WIRE (for LHD)

a.
E238210

for LH Side:

i.

Disconnect each connector.


ii.
E238209

Disconnect the connector from the connector holder.


iii.

Remove the bolt.


iv.

Disengage each clamp and disconnect the connector holder.



b.
E238208

for RH Side:

i.

Disconnect each connector.


ii.
E238211

Remove the bolt.


iii.

Disengage each clamp and disconnect the connector holder.



c.

Remove the 2 bolts <A> and disconnect the 2 earth wires.

E249751E02
6.708,1.406 6.26,1.073 true 3.052,0.5 3.49,0.74 true 6.729,1.313 6.958,1.51 0.229,0.198 10 true *1 2.844,0.396 3.042,0.563 0.198,0.167 10 true *1 3.552,0.396 3.781,0.573 0.229,0.177 10 true *2 6.667,0.688 6.875,0.896 0.208,0.208 10 true *2 1.042,1.344 1.281,1.542 0.24,0.198 10 true *3

Text in Illustration
*1 Earth Wire *2 Bolt <A>
*3 Bolt <B> - -


d.

Remove the bolt <B>.


e.

Disconnect the connector.


f.

Disengage each clamp.


g.

Remove the bolt and disconnect the earth wire.

E249752E02
2.813,0.573 3.125,1.042 true 2.635,0.49 2.854,0.698 0.219,0.208 10 true *1

Text in Illustration
*1 Earth Wire - -


h.

Disconnect the connector.


i.

Disengage each clamp and disconnect the instrument panel wire.


Hide 82141 30.DISCONNECT INSTRUMENT PANEL WIRE (for RHD)

a.
E235011

for RH Side:

i.

Disconnect each connector.


ii.
E235012

Disconnect the connector from the connector holder.


iii.

Remove the bolt.


iv.

Disengage each clamp and disconnect the connector holder.



b.
E235013

for LH Side:

i.

Disconnect each connector.


ii.
E235014

Remove the bolt.


iii.

Disengage each clamp and disconnect the connector holder.



c.

Remove the 2 bolts and disconnect the 2 earth wires.

E249746E02
5.458,0.615 5.99,0.469 true 1.458,1.323 1.021,0.792 true 0.865,0.688 1.073,0.875 0.208,0.188 10 true *1 5.271,0.542 5.458,0.75 0.188,0.208 10 true *1

Text in Illustration
*1 Earth Wire - -


d.

Disconnect each connector.


e.

Disengage each clamp.


f.

Remove the bolt <A> and disconnect the earth wire.

E249747E02
1.896,5.854 1.885,6.292 true 1.823,6.313 2.021,6.51 0.198,0.198 10 true *1 2.083,5.969 2.292,6.156 0.208,0.188 10 true *2 1.594,1.385 1.792,1.583 0.198,0.198 10 true *3

Text in Illustration
*1 Earth Wire *2 Bolt <A>
*3 Bolt <B> - -


g.

Remove the bolt <B>.


h.

Disconnect the connector.


i.

Disengage each clamp and disconnect the instrument panel wire.


Hide 55330B 31.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

a.

Remove the 8 bolts and 3 screws, and remove the instrument panel reinforcement.

E249753E02
0.406,0.146 0.615,0.344 0.208,0.198 10 true *1 2.698,0.135 2.896,0.323 0.198,0.188 10 true *1 5,0.135 5.198,0.333 0.198,0.198 10 true *1 5.479,4.948 5.688,5.125 0.208,0.177 10 true *1 3.375,5.344 3.573,5.531 0.198,0.188 10 true *2 0.167,5.354 0.354,5.542 0.188,0.188 10 true *2

Text in Illustration
*1 Bolt *2 Screw


Hide 55950G 32.REMOVE DEFROSTER NOZZLE ASSEMBLY

a.
E238215

Disengage the 2 claws and 3 guides and remove the defroster nozzle assembly.


Hide 88539J 33.DISCONNECT DRAIN COOLER HOSE

a.
E238216

Disconnect the drain cooler hose.


Hide 34.REMOVE AIR CONDITIONER UNIT ASSEMBLY

a.

Remove the 3 bolts and nut, and remove the air conditioner unit assembly.

E249223


Hide 87050 35.REMOVE AIR CONDITIONING RADIATOR ASSEMBLY (for LHD)

a.

Disconnect the connector.

E238218


b.

Remove the 3 screws and air conditioning radiator assembly.


Hide 87050 36.REMOVE AIR CONDITIONING RADIATOR ASSEMBLY (for RHD)

a.

Disconnect the connector.

E249224


b.

Remove the 3 screws and air conditioning radiator assembly.


Hide 88897P 37.REMOVE ASPIRATOR

a.
E238219

Disengage the 2 claws and remove the aspirator.


Hide 88650N 38.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY

a.
E238220

Disconnect the connector.


b.

Remove the screw.


c.

Remove the air conditioning amplifier assembly as shown in the illustration.

E238221


Hide 82210K 39.REMOVE AIR CONDITIONING HARNESS ASSEMBLY (for LHD)

a.

Disengage each clamp.

E238224


b.

Disconnect each connector and remove the air conditioning harness assembly.


Hide 82210K 40.REMOVE AIR CONDITIONING HARNESS ASSEMBLY (for RHD)

a.

Disengage each clamp.

E235028


b.

Disconnect each connector and remove the air conditioning harness assembly.


Hide 87201F 41.REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY

a.
E238223

Disengage the 3 claws and remove the No. 3 air duct sub-assembly.

NOTICE:

If any of the claws of the No. 3 air duct subassembly have been cracked or deformed during removal, make sure to replace the air duct with a new one. Failure to do so may cause the No. 3 air duct sub-assembly to fall off or noise to occur.



Hide 87201B 42.REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY

a.
E238222

Disengage the 3 claws and remove the No. 2 air duct sub-assembly.

NOTICE:

If any of the claws of the No. 2 air duct subassembly have been cracked or deformed during removal, make sure to replace the air duct with a new one. Failure to do so may cause the No. 3 air duct sub-assembly to fall off or noise to occur.