Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2014.12
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278125 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

The temperature can be adjusted and the air inlet can be switched between fresh air mode and recirculated mode by operating switches on the steering pad switch RH. The air conditioning panel (heater control switch board) receives operation signals from the steering pad switch RH via the spiral with sensor cable sub-assembly and sends temperature setting and air inlet change signals to the air conditioning amplifier assembly.

WIRING DIAGRAM

E245293E08
1.177,1.406 1.458,1.583 0.281,0.177 10 false R/F 2.823,0.865 3.073,1.031 0.25,0.167 10 false z2 2.823,2.604 3.073,2.771 0.25,0.167 10 false z2 3.125,0.771 3.438,0.938 0.313,0.167 10 false AC1 3.74,0.771 4.052,0.938 0.313,0.167 10 false AC1 5.573,0.781 5.688,0.948 0.115,0.167 10 false 3 5.177,1.26 5.49,1.427 0.313,0.167 10 false G33 2.865,0.677 2.99,0.844 0.125,0.167 10 false 3 3.125,2.5 3.438,2.667 0.313,0.167 10 false EAU 2.844,2.406 2.969,2.573 0.125,0.167 10 false 8 4.146,2.594 4.354,2.76 0.208,0.167 10 false G5 3.729,2.5 4.042,2.667 0.313,0.167 10 false EAU 4.188,2.406 4.313,2.573 0.125,0.167 10 false 4 4.146,0.885 4.354,1.052 0.208,0.167 10 false G5 5.729,0.865 6.115,1.031 0.385,0.167 10 false SWO 4.156,0.688 4.344,0.854 0.188,0.167 10 false 10 1.042,2.052 1.583,2.229 0.542,0.177 10 false TEMP+ 1.042,2.656 1.583,2.833 0.542,0.177 10 false TEMP- 0.625,3.448 1.906,3.854 1.281,0.406 10 false Steering Pad Switch RH 2.979,2.948 4.49,3.333 1.51,0.385 10 false Spiral Cable with Sensor Sub-assembly 5.177,1.427 7.104,1.802 1.927,0.375 10 false Air Conditioning Panel (Heater Control Switch Board)

PROCEDURE

1.INSPECT AIR CONDITIONING PANEL (HEATER CONTROL SWITCH BOARD)
a.

Disconnect the G5 spiral cable with sensor sub-assembly connector.


b.
U183669E01
1.574,0.232 1.794,0.395 0.220,0.163 10 G5 0.148,0.095 0.468,0.257 0.320,0.163 10 *a 2.21,1.745 2.530,1.907 0.320,0.163 10 AC1 1.827,1.277 2.193,1.785 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G5-10 (AC1) - Body ground Power switch off Below 1 V
G5-10 (AC1) - Body ground Power switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)



OK

2.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING PANEL (HEATER CONTROL SWITCH BOARD) - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY)
2.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Disconnect the steering pad switch RH and spiral cable with sensor sub-assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

E343939E02
4.302,3.042 4.625,3.25 0.323,0.208 2.49,0.594 2.813,0.802 0.323,0.208 2.594,1.156 2.198,0.771 false 2.844,1.583 2.615,1.333 false 4.979,3.094 4.688,3.49 false 4.688,3.656 4.313,4.083 false 0.156,0.167 0.427,0.365 0.271,0.198 10 false *a 4.365,3.063 4.646,3.24 0.281,0.177 10 false G5 2.573,0.604 2.802,0.781 0.229,0.177 10 false z2 2,0.594 2.323,0.781 0.323,0.188 10 false AC1 2.865,1.583 3.188,1.771 0.323,0.188 10 false EAU 4.156,4.115 4.479,4.302 0.323,0.188 10 false EAU 5.021,2.99 5.344,3.177 0.323,0.188 10 false AC1

Standard Resistance:
Tester Connection Condition Specified Condition
z2-8 (EAU) - G5-4 (EAU) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right
z2-3 (AC1) - G5-10 (AC1) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right



c.

After setting the spiral cable with sensor cable sub-assembly to the center position, rotate the spiral cable with sensor cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-8 (EAU) - G5-4 (EAU) Always Below 3 Ω
z2-3 (AC1) - G5-10 (AC1) Always Below 3 Ω


NOTICE:
·

The spiral cable with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

·

As the spiral cable with sensor cable sub-assembly may break, do not rotate the spiral cable with sensor cable sub-assembly more than the specified amount.



HINT:

Text in Illustration
*a Component without harness connected
(SpiralC cable with sensor Cable Sub-assembly)




OK

3.INSPECT STEERING PAD SWITCH RH

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

3.INSPECT STEERING PAD SWITCH RH
a.

Remove the steering pad switch RH (See page Steering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

U183749E01
2.926,2.46 3.094,2.623 0.167,0.163 10 z2 4.068,2.358 4.374,2.521 0.306,0.163 10 AC1 5.798,0.355 6.105,0.518 0.306,0.163 10 *1 6.422,1.328 6.728,1.491 0.306,0.163 10 *3 6.029,2.134 6.336,2.297 0.306,0.163 10 *2 4.068,2.929 4.374,3.092 0.306,0.163 10 EAU 0.267,0.225 0.420,0.409 0.152,0.184 10 *a 3.593,2.486 3.593,2.42 3.593,2.42 4.049,2.42 false 3.59,2.691 3.59,2.985 3.59,2.985 4.056,2.985 false 5.51,1.196 5.51,0.418 5.51,0.418 5.776,0.418 false 5.509,1.588 5.509,2.19 5.509,2.19 5.993,2.19 false 5.744,1.399 6.382,1.399 false

Text in Illustration
*1 TEMP + Switch *2 TEMP - Switch
*3 R/F Switch - -
*a Component without harness connected
(Steering Pad Switch RH)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
z2-3 (AC1) - z2-8 (EAU) No switch pushed 95 to 105 kΩ
z2-3 (AC1) - z2-8 (EAU) R/F switch pushed 323 to 335 Ω
z2-3 (AC1) - z2-8 (EAU) TEMP + switch pushed 980 to 1020 Ω
z2-3 (AC1) - z2-8 (EAU) TEMP - switch pushed 3048 to 3172 Ω




OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND)

NG

REPLACE STEERING PAD SWITCH RH

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-4 (EAU) - Body ground Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING PANEL (HEATER CONTROL SWITCH BOARD) - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-10 (AC1) - G33-3 (SWO) Always Below 1 Ω
G5-10 (AC1) - Body ground Always 10 kΩ or higher




OK

REPLACE AIR CONDITIONING PANEL (HEATER CONTROL SWITCH BOARD)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR