Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2014.12
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278125 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1473/73  A/C Inverter Start-up Signal System Malfunction  


DESCRIPTION

The inverter activation signal is sent to the compressor with motor assembly from the hybrid vehicle control ECU. Compressor control is stopped and the DTC is stored if there is an open or short in the signal circuit.

DTC No. DTC Detection Condition Trouble Area
B1473/73 Open or short in A/C inverter start-up signal system
·

Harness or connector between hybrid vehicle control ECU and compressor with motor assembly

·

Compressor with motor assembly

·

Hybrid vehicle control ECU

·

Hybrid control system

·

CAN communication system



WIRING DIAGRAM

E235673E44
0.281,6.281 1.333,6.74 1.052,0.458 10 false Compressor with Motor Assembly 5.958,4.063 6.885,4.542 0.927,0.479 10 false Hybrid Vehicle Control ECU 6.052,1.844 6.344,1.99 0.292,0.146 10 false STB 6.052,2.854 6.344,3 0.292,0.146 10 false ITE 6.052,3.375 6.344,3.521 0.292,0.146 10 false CLK 6.052,2.354 6.292,2.5 0.24,0.146 10 false ETI 0.854,1.833 1.188,1.979 0.333,0.146 10 false STBI 0.927,2.854 1.188,3 0.26,0.146 10 false DIN 0.906,3.344 1.198,3.49 0.292,0.146 10 false CLK 0.948,3.917 1.188,4.063 0.24,0.146 10 false IG1 0.865,4.479 1.198,4.625 0.333,0.146 10 false GND 0.979,5.281 1.292,5.51 0.313,0.229 10 false PE 0.979,5.781 1.344,6.042 0.365,0.26 10 false PB 0.771,2.333 1.188,2.479 0.417,0.146 10 false DOUT 1.333,1.833 1.646,2.052 0.313,0.219 10 false C22 1.333,2.344 1.615,2.49 0.281,0.146 10 false C22 1.333,2.844 1.615,2.99 0.281,0.146 10 false C22 1.333,3.365 1.615,3.51 0.281,0.146 10 false C22 1.333,4.479 1.615,4.646 0.281,0.167 10 false C22 1.333,3.917 1.615,4.063 0.281,0.146 10 false C22 5.781,1.74 5.969,1.885 0.188,0.146 10 false 11 5.854,2.24 6.031,2.385 0.177,0.146 10 false 8 5.854,2.76 6.031,2.906 0.177,0.146 10 false 9 5.792,3.271 5.969,3.417 0.177,0.146 10 false 10 4.927,7.104 7.063,7.365 2.135,0.26 10 false Inverter with Converter Assembly 5.229,5.677 5.333,5.844 0.104,0.167 10 false 1 5.229,5.156 5.333,5.323 0.104,0.167 10 false 2 1.365,5.25 1.74,5.521 0.375,0.271 10 false D1 1.365,5.771 1.729,6.031 0.365,0.26 10 false D1 1.427,5.073 1.531,5.219 0.104,0.146 10 false 1 1.438,5.583 1.542,5.75 0.104,0.167 10 false 2 1.417,1.646 1.521,1.792 0.104,0.146 10 false 4 1.417,2.146 1.521,2.313 0.104,0.167 10 false 3 1.417,2.667 1.521,2.813 0.104,0.146 10 false 2 1.417,3.167 1.521,3.333 0.104,0.167 10 false 1 1.417,3.74 1.521,3.885 0.104,0.146 10 false 6 1.427,4.292 1.531,4.458 0.104,0.167 10 false 5 5.406,5.156 5.813,5.302 0.406,0.146 10 false ACPE 5.406,5.667 5.813,5.813 0.406,0.146 10 false ACPB 5.719,5.938 6.229,6.531 0.51,0.594 10 false Electric Vehicle Fuse 2.583,4.042 3.115,4.25 0.531,0.208 10 false HTR-IG 4.167,3.906 5.563,4.052 1.396,0.146 10 false from IG1 NO. 1 Relay 2.26,7.135 3.979,7.281 1.719,0.146 10 false : CAN Communication Line 4.927,6.948 5.177,7.156 0.25,0.208 10 false D2 5.958,3.896 6.25,4.083 0.292,0.188 10 false A72 0.281,1.063 2.563,1.26 2.281,0.198 10 false Air Conditioning Amplifier Assembly 2.729,6.313 3.938,6.542 1.208,0.229 10 false No. 2 Engine Wire

CAUTION / NOTICE / HINT

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the diagnosis procedure for the hybrid control system first if any DTCs from those systems are output simultaneously.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B




A

2.CHECK DIAGNOSTIC TROUBLE CODE

B

2.CHECK DIAGNOSTIC TROUBLE CODE
a.

Check if DTCs for the air conditioning system and the hybrid control system are output using the intelligent tester.

Result:
Result Proceed to
Only DTC B1473 is output A
DTCs B1473 and P3108 are output simultaneously (B1498 is not output)
DTCs B1473 and B1498 are output simultaneously (P3108 is not output) B
DTCs B1473, B1498 and P3108 are output simultaneously
DTCs other than P3108 are output for hybrid control system C




A

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR)

B

C

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR)
CAUTION:

Do not disconnect the connector on the high-voltage side.


a.

Disconnect the A72 hybrid vehicle control ECU connector.


b.

Disconnect the C22 compressor with motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A72-11 (STB) - C22-4 (STBI) Always Below 1 Ω
A72-11 (STB) - Body ground Always 10 kΩ or higher




OK

4.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY
a.

Reconnect the C22 compressor with motor assembly connector.


b.
U183750E02
1.385,2.094 1.177,2.906 false 0.198,0.115 0.385,0.281 0.188,0.167 10 false *a 1.615,0.49 1.917,0.688 0.302,0.198 10 false A72 0.979,2.979 1.292,3.135 0.313,0.156 10 false STB

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A72-11 (STB) - Body ground Power switch on (IG) 11 to 14 V
A72-11 (STB) - Body ground Power switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)



OK

NG

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY