58165F
1.REMOVE FRONT FLOOR COVER RH
58166B
2.REMOVE FRONT FLOOR COVER LH
58167H
3.REMOVE FRONT CENTER FLOOR COVER
71940A
4.REMOVE REAR SEAT HEADREST ASSEMBLY
71960B
5.REMOVE REAR CENTER SEAT HEADREST ASSEMBLY
6.REMOVE REAR SEATBACK ASSEMBLY RH
7.REMOVE REAR SEATBACK ASSEMBLY LH
8.REMOVE REAR SEAT CUSHION ASSEMBLY
67918A
9.REMOVE REAR DOOR SCUFF PLATE LH
Disengage the 5 claws and guide and remove the rear door scuff plate LH.
67914
10.REMOVE FRONT DOOR SCUFF PLATE LH
Disengage the 8 claws and remove the front door scuff plate LH.
62112
11.REMOVE COWL SIDE TRIM BOARD LH
Remove the clip.
Disengage the clip and remove the cowl side trim board LH.
62312B
12.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Remove the front door opening trim weatherstrip LH.
62212
13.REMOVE FRONT PILLAR GARNISH LH
Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.
| *1 | Front Pillar Garnish Clip |
Let the front pillar garnish LH hang down from the front pillar garnish clip.
Using needle-nose pliers with the tips wrapped with protective tape, rotate the front pillar garnish clip 90° in the direction indicated by the arrow (1) shown in the illustration.
| *a | 90° |
| *b | Protective Tape |
Pull the front pillar garnish LH in the direction indicated by the arrow (2) shown in the illustration to disengage it from the front pillar garnish clip.
If the front pillar garnish clip is not removed from the vehicle body and is not damaged, the front pillar garnish clip can be reused.
If the front pillar garnish clip is removed from the vehicle body, make sure to replace it with a new one.
Pull the front pillar garnish LH in the direction indicated by the arrow (3) shown in the illustration to disengage the 2 guides to remove the front pillar garnish LH.
Protect the curtain shield airbag assembly.
| *1 | Adhesive Tape |
| *2 | Protective Cover |
| *3 | Curtain Shield Airbag Assembly |
Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
62332A
14.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Remove the rear door opening trim weatherstrip LH.
73233C
15.REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)
73220
16.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
62414A
17.REMOVE CENTER PILLAR LOWER GARNISH LH
Disengage the 4 claws and 2 clips, and remove the center pillar lower garnish LH.
62412B
18.REMOVE CENTER PILLAR UPPER GARNISH LH
Remove the 2 screws and disengage the clip.
Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.
67917A
19.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
67913
20.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
62111C
21.REMOVE COWL SIDE TRIM BOARD RH
Use the same procedure as for the LH side.
62311B
22.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62211
23.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
62331A
24.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
73233
25.REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)
Use the same procedure as for the LH side.
73210
26.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
62413A
27.REMOVE CENTER PILLAR LOWER GARNISH RH
Use the same procedure as for the LH side.
62411B
28.REMOVE CENTER PILLAR UPPER GARNISH RH
Use the same procedure as for the LH side.
58410B
29.REMOVE DECK BOARD ASSEMBLY
Remove the deck board assembly.
64997
30.REMOVE DECK FLOOR BOX LH
Remove the deck floor box LH.
64995
31.REMOVE DECK FLOOR BOX RH
Use the same procedure as for the LH side.
64330D
32.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
Remove the package tray trim panel assembly.
64716D
33.REMOVE REAR DECK TRIM COVER
Remove the 2 clips.
Disengage the 4 claws and 2 guides, and remove the rear deck trim cover.
73370
34.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
58732C
35.REMOVE REAR ABSORBER CAP LH
Disengage the 2 claws and 2 guides, and remove the rear absorber cap LH.
81330
36.REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
64740C
37.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.
| *1 | Rear Seatback Hinge | - | - |
Remove the bolt and 2 screws.
Disengage the 4 claws, 4 clips and guide, and remove the deck trim side panel assembly LH.
62472A
38.REMOVE ROOF SIDE INNER GARNISH LH
Disengage the 5 clips.
Pass the floor anchor of the rear seat 3 point type outer belt assembly LH through the roof side inner garnish LH and remove the roof side inner garnish LH.
73360
39.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
58731C
40.REMOVE REAR ABSORBER CAP RH
Use the same procedure as for the LH side.
64730B
41.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
Use the same procedure as for the LH side.
73350
42.DISCONNECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY
62471A
43.REMOVE ROOF SIDE INNER GARNISH RH
Using a moulding remover, disengage the 4 claws and guide, and disconnect the belt guide.
Disengage the 5 clips.
Pass the floor anchor of the rear seat 3 point type outer belt assembly RH through the roof side inner garnish RH and remove the roof side inner garnish RH.
81260A
44.REMOVE MAP LIGHT ASSEMBLY
74610S
45.REMOVE ASSIST GRIP ASSEMBLY
Use the same procedure to remove all assist grips.
Using a moulding remover, disengage the 4 claws and remove the 2 assist grip covers.
Disengage the 2 clips and remove the assist grip.
74320
46.REMOVE VISOR ASSEMBLY LH
Disconnect the visor shaft from the visor holder.
Remove the 2 screws and the visor assembly LH.
74310
47.REMOVE VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74348
48.REMOVE VISOR HOLDER
Turn the visor holder clockwise 45° and disengage the 2 claws to remove the visor holder.
Use the same procedure for the LH side and RH side.
49.REMOVE ROOF HEADLINING ASSEMBLY
| *A | 1 Claw Type | - | - |
| *a | Front Pillar RH Side | *b | Front Pillar LH Side |
| *c | Rear Pillar RH Side | - | - |
| *A | 2 Claws Type | - | - |
| *a | Front Pillar RH Side | *b | Front Pillar LH Side |
| *c | Rear Pillar RH Side | - | - |
for front pillar RH side:
Disconnect the connector.
Using a clip remover, disengage the 3 clamps.
for front pillar LH side:
Disconnect the connector.
Using a clip remover, disengage the 3 clamps.
for rear pillar RH side:
Disconnect the connector.
Remove the bolt and disconnect the connector bracket.
Using a clip remover, disengage the 2 clamps.
Using a clip remover, remove the 3 clips.
Disengage the claw. (for 1 Claw Type)
Disengage the 2 claws. (for 2 Claws Type)
Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.
Do not damage the roof headlining assembly or body interior.