Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2011.12–2017.06
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278147 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

When the power switch is on (IG), the power window regulator motor assembly (for driver door) is operated by the power window regulator master switch assembly. The power window regulator motor assembly (for driver door) has motor, regulator and ECU functions.

WIRING DIAGRAM

B281016E18
0.269,2.289 2.276,2.705 2.008,0.415 10 Main Body ECU (Multiplex Network Body ECU) 0.965,3.368 2.611,3.524 1.647,0.156 10 : LIN Communication Line 0.415,0.529 1.321,0.869 0.906,0.340 10 from Auxiliary Battery 1.852,0.669 2.464,0.825 0.612,0.156 10 DOOR D 2.52,2.41 4.574,2.816 2.054,0.406 10 Power Window Regulator Motor Assembly (for Driver Door) 5.228,2.406 6.838,2.765 1.610,0.360 10 Power Window Regulator Master Switch Assembly 2.52,2.251 3.527,2.412 1.008,0.161 10 J3*1, H3*2 5.228,2.247 5.951,2.407 0.723,0.161 10 J1*1, H1*2 1.635,1.589 2.015,1.745 0.380,0.156 10 LIN2 2.833,1.449 3.095,1.605 0.262,0.156 10 LIN 2.833,0.426 2.962,0.582 0.129,0.156 10 B 3.799,0.426 4.206,0.582 0.407,0.156 10 AUTO 5.373,0.524 5.798,0.680 0.426,0.156 10 AUTO 5.373,1.033 5.507,1.189 0.134,0.156 10 D 5.373,1.528 5.507,1.684 0.134,0.156 10 U 5.373,1.832 5.507,1.988 0.134,0.156 10 E 3.724,0.93 4.238,1.086 0.514,0.156 10 DOWN 3.962,1.44 4.207,1.595 0.245,0.156 10 UP 3.87,1.729 4.237,1.885 0.367,0.156 10 GND 4.252,1.729 4.381,1.885 0.129,0.156 10 1 4.252,0.935 4.381,1.091 0.129,0.156 10 7 5.209,0.935 5.338,1.091 0.129,0.156 10 5 4.821,1.458 5.321,1.614 0.500,0.156 10 8*1,1*2 4.821,1.748 5.307,1.904 0.486,0.156 10 1*1,9*2 4.252,0.426 4.381,0.582 0.129,0.156 10 4 5.209,0.426 5.338,0.582 0.129,0.156 10 4 4.252,1.449 4.437,1.605 0.185,0.156 10 10 2.641,0.426 2.770,0.582 0.129,0.156 10 2 2.633,1.449 2.804,1.605 0.172,0.156 10 9 3.299,3.157 4.083,3.313 0.784,0.156 10 *1: for LHD 3.299,3.442 4.083,3.598 0.784,0.156 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.

·

If a power window regulator motor assembly (for driver door) has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

When the ECU determines that the power window regulator motor assembly (for driver door) has a malfunction, DTC B2311 is stored.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (MAIN BODY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch to on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Communication D-Door Motor Connection status between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) / OK or STOP OK: Normal communication
STOP: Communication stopped
-

OK:

On the intelligent tester screen, OK is displayed.




OK

2.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)

NG

GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting)

2.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)
a.

Enter the following menus: Body / D-Door Motor / Data List.


b.

Read the Data List according to the display on the intelligent tester.

D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door))
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal / ON or OFF ON: Driver door power window manual up switch operated
OFF: Driver door power window manual up switch not operated
-
D Door P/W Down SW Driver door power window manual down switch signal / ON or OFF ON: Driver door power window manual down switch operated
OFF: Driver door power window manual down switch not operated
-

OK:

On the intelligent tester screen, ON or OFF is displayed accordingly.




OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND)
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)
a.

Enter the following menus: Body / D-Door Motor / Active Test.


b.

Perform the Active Test according to the display on the intelligent tester.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door))
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF / UP / DOWN -

OK:

Driver door power window operates normally.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the power window regulator motor assembly (for driver door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
J3-2 (B) - Body ground Power switch off 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
H3-2 (B) - Body ground Power switch off 11 to 14 V


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
J3-1 (GND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
H3-1 (GND) - Body ground Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER) AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER) AND BODY GROUND)
a.

Disconnect the power window regulator master switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
J1-8 (U) - J3-10 (UP) Always Below 1 Ω
J1-5 (D) - J3-7 (DOWN) Always Below 1 Ω
J1-8 (U) - Body ground Always 10 kΩ or higher
J1-5 (D) - Body ground Always 10 kΩ or higher
J1-1 (E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
H1-1 (U) - H3-10 (UP) Always Below 1 Ω
H1-5 (D) -H3-7 (DOWN) Always Below 1 Ω
H1-1 (U) - Body ground Always 10 kΩ or higher
H1-5 (D) - Body ground Always 10 kΩ or higher
H1-9 (E) - Body ground Always Below 1 Ω




OK

6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B298969E42
1.073,0.844 1.115,1.656 false 2.344,0.844 2.313,1.656 false 1.677,1.792 1.458,2.635 false 1.219,1.792 0.948,2.656 false 0.198,0.083 0.385,0.271 0.188,0.188 10 false *a 0.927,0.646 1.229,0.833 0.302,0.188 10 false E*B 2.042,0.646 2.625,0.833 0.583,0.188 10 false E*A,U*B 0.823,2.667 1.115,2.854 0.292,0.188 10 false U*A 1.385,2.667 1.542,2.854 0.156,0.188 10 false D

Remove the power window regulator master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Switch Condition Specified Condition
8 (U) - 1 (E) Manual UP Below 1 Ω
5 (D) - 1 (E) Manual DOWN Below 1 Ω

for RHD
Tester Connection Switch Condition Specified Condition
1 (U) - 9 (E) Manual UP Below 1 Ω
5 (D) - 9 (E) Manual DOWN Below 1 Ω


Text in Illustration
*A for LHD
*B for RHD
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY