Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278157 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  INSTALLATION  


PROCEDURE

Hide 64828B 1.INSTALL BACK WINDOW GLASS CLIP LH

a.

Using a brush or sponge, coat the application area of new back window glass clip LH with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G coating to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B298783E03
1.688,3.646 1.573,3.885 false 1.458,3.865 1.667,4.063 0.208,0.198 10 false *1 0.135,0.052 0.344,0.25 0.208,0.198 10 false *A

Install a new back window glass clip LH onto the back door glass as shown in the illustration.

Text in Illustration
*A Back Side
*1 Ceramic Notch


Hide 64827B 2.INSTALL BACK WINDOW GLASS CLIP RH

a.

Using a brush or sponge, coat the application area of new back window glass clip RH with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G coating to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B293588E02
0.105,0.032 0.333,0.220 0.229,0.188 10 *A 1.763,3.95 1.992,4.137 0.229,0.188 10 *1 1.727,3.621 1.819,3.927 false

Install a new back window glass clip RH onto the back door glass as shown in the illustration.

Text in Illustration
*A Back Side
*1 Ceramic Notch


Hide 64813B 3.INSTALL BACK WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the application area of a new back window glass adhesive dam with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G coating to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
U159235E03
0.365,1.198 0.438,1.438 false 3.125,1.219 3.052,1.448 false 0.698,1.188 0.833,1.365 0.135,0.177 10 false A 0.76,0.479 0.896,0.656 0.135,0.177 10 false A 0.375,1.448 0.552,1.646 0.177,0.198 10 false *1 2.969,1.458 3.146,1.656 0.177,0.198 10 false *1 1.719,0.615 1.896,0.813 0.177,0.198 10 false a 0.594,2.844 1.01,3.021 0.417,0.177 10 false A-A 2.594,2.99 2.771,3.188 0.177,0.198 10 false b 0.115,0.063 0.313,0.24 0.198,0.177 10 false *A

Cut a new back window glass adhesive dam (a) so that it fits to the position specified in the illustration.

Text in Illustration
*A Back Side
*1 Ceramic Notch for Dam Alignment

Standard Dimension:
Area Dimension
a 1053 mm (3.45384 ft.)
b 3.0 mm (0.118 in.)



c.

Install a new back window glass adhesive dam onto the back door glass as shown in the illustration.


d.
U159236E03
0.438,1.448 0.292,1.615 false 3.01,1.438 3.146,1.604 false 0.76,2.135 0.896,2.313 0.135,0.177 10 false A 0.802,1.438 0.938,1.615 0.135,0.177 10 false A 0.448,1.313 0.625,1.51 0.177,0.198 10 false *1 2.813,1.344 2.99,1.542 0.177,0.198 10 false *1 1.625,2.01 1.802,2.208 0.177,0.198 10 false a 0.417,2.646 0.833,2.823 0.417,0.177 10 false A-A 0.99,2.99 1.167,3.188 0.177,0.198 10 false b 0.094,0.031 0.292,0.208 0.198,0.177 10 false *A

Cut a new back window glass adhesive dam (a) so that it fits to the position specified in the illustration.

Text in Illustration
*A Back Side
*1 Ceramic Notch for Dam Alignment

Standard Dimension:
Area Dimension
a 1070 mm (3.5096 ft.)
b 13.2 mm (0.52 in.)



e.

Install a new back window glass adhesive dam onto the back door glass as shown in the illustration.


Hide 68131 4.INSTALL BACK DOOR GLASS SUB-ASSEMBLY

a.
B296206E02
1.667,0.51 1.448,0.51 1.448,0.51 1.448,0.885 true 1.656,0.781 1.448,0.781 false 1.365,0.896 1.615,1.104 0.25,0.208 10 false *1

Position the back door glass sub-assembly.

Text in Illustration
*1 Matchmark

i.

Using suction cups, place the back door glass sub-assembly in the correct position.


ii.

Check that the whole contact surface of the back door glass rim is perfectly even.


iii.

Align the matchmarks on the back door glass and vehicle body.

NOTICE:

Check that the back door glass clips are attached to the vehicle body correctly.



iv.

Remove the back door glass.



b.

Using a brush, coat the installation surface on the vehicle body with primer M.

B293592E03
0.128,3.542 0.347,3.697 0.219,0.155 0.881,2.691 1.053,2.854 0.172,0.163 10 *1 0.368,3.541 0.693,3.703 0.325,0.163 10 : *2 0.768,2.958 0.941,2.803 false 3.685,0.502 3.948,0.702 0.263,0.200 10 A-A 3.684,2.241 3.947,2.440 0.263,0.200 10 B-B 5.5,0.495 5.815,0.694 0.315,0.200 10 C-C 1.394,0.205 1.517,0.379 0.123,0.174 10 A 1.384,0.633 1.507,0.807 0.123,0.174 10 A 3.349,0.67 3.471,0.844 0.123,0.174 10 C 2.685,0.75 2.808,0.925 0.123,0.174 10 C 1.381,1.494 1.504,1.669 0.123,0.174 10 B 1.385,1.034 1.507,1.208 0.123,0.174 10 B 2.515,3.366 2.688,3.529 0.172,0.163 10 *3 2.729,3.362 2.661,3.426 false 1.393,2.625 1.565,2.788 0.172,0.163 10 *a 2.511,2.625 2.683,2.787 0.172,0.163 10 *b 0.146,3.564 0.325,3.683 0.179,0.119 0.208,3.683 0.325,3.567 false 0.242,3.683 0.325,3.6 false 0.275,3.683 0.325,3.633 false 0.309,3.683 0.325,3.667 false 0.147,3.644 0.227,3.564 false 0.146,3.678 0.26,3.564 false 0.147,3.576 0.159,3.564 false 0.147,3.61 0.193,3.564 false 0.175,3.683 0.294,3.564 false 5.089,1.199 5.261,1.362 0.172,0.163 10 *c 5.569,0.718 5.741,0.881 0.172,0.163 10 *c 3.86,2.398 4.032,2.560 0.172,0.163 10 *c 5.154,2.536 5.326,2.699 0.172,0.163 10 *c

Text in Illustration
*1 Brush *2 Primer M
*3 Adhesive - -
*a CORRECT *b INCORRECT
*c Edge of Curved Surface - -

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Allow the primer M coating to dry for 3 minutes or more.

·

Throw away any leftover primer M.



HINT:

If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.



c.

Using a brush or sponge, coat the adhesive application area with primer G.

B293589E03
0.542,2.146 3.51,3.365 2.969,1.219 4.052,2.146 7.021,3.365 2.969,1.219 4.052,0.292 7.021,1.51 2.969,1.219 0.469,3.448 0.792,3.615 0.323,0.167 10 false : *1 0.594,2.188 0.854,2.385 0.26,0.198 10 false A-A 4.094,0.333 4.354,0.531 0.26,0.198 10 false B-B 4.094,2.198 4.406,2.396 0.313,0.198 10 false C-C 1.625,0.385 1.75,0.563 0.125,0.177 10 false A 1.625,0.813 1.75,0.99 0.125,0.177 10 true A 3.667,0.656 3.792,0.833 0.125,0.177 10 false B 3.198,0.74 3.323,0.917 0.125,0.177 10 true B 1.635,1.76 1.76,1.938 0.125,0.177 10 false C 1.635,1.302 1.76,1.479 0.125,0.177 10 true C 2.104,2.354 2.281,2.521 0.177,0.167 10 false a 5.219,0.531 5.396,0.698 0.177,0.167 10 false b 6.271,0.531 6.448,0.698 0.177,0.167 10 false c 5.635,2.354 5.813,2.521 0.177,0.167 10 false d 0.146,0.135 0.469,0.302 0.323,0.167 10 false *A

Text in Illustration
*A Back Side - -
*1 Primer G - -

Standard Dimension:
Area Dimension
a 9.0 mm (0.354 in.) or more
b 22.0 mm (0.866 in.) or more
c 23.9 mm (0.941 in.) or more
d 16.0 mm (0.63 in.) or more


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G coating to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



d.

Apply adhesive to the glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B214800E31
1.188,0.427 1.375,0.49 false 0.563,0.615 0.719,0.813 0.156,0.198 10 false a 1.333,1.427 1.49,1.625 0.156,0.198 10 false a 1.125,0.865 1.281,1.063 0.156,0.198 10 false b 0.75,1.042 0.906,1.24 0.156,0.198 10 false b 1.406,0.438 1.583,0.604 0.177,0.167 10 false *1

Cut off the tip of the cartridge nozzle as shown in the illustration.

Text in Illustration
*1 Nozzle

Standard Dimension:
Area Dimension
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)


HINT:

After cutting off the tip, use all adhesive within the time described in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour and 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the back door glass as shown in the illustration.

B293590E03
0.469,1.938 3.469,3.365 3,1.427 4.083,1.938 7.083,3.365 3,1.427 4.083,0.125 7.083,1.552 3,1.427 0.469,3.438 0.792,3.604 0.323,0.167 10 false : *1 0.521,1.979 0.781,2.177 0.26,0.198 10 false A-A 4.135,0.177 4.396,0.375 0.26,0.198 10 false B-B 4.135,1.979 4.448,2.177 0.313,0.198 10 false C-C 1.667,0.385 1.792,0.563 0.125,0.177 10 false A 1.646,0.844 1.771,1.021 0.125,0.177 10 true A 3.677,0.688 3.802,0.865 0.125,0.177 10 false B 3.198,0.74 3.323,0.917 0.125,0.177 10 true B 1.656,1.76 1.781,1.938 0.125,0.177 10 false C 1.667,1.302 1.792,1.479 0.125,0.177 10 true C 2.271,2.115 2.531,2.313 0.26,0.198 10 false a 5.313,0.292 5.573,0.49 0.26,0.198 10 false b 6.167,0.292 6.427,0.49 0.26,0.198 10 false c 5.573,2.094 5.833,2.292 0.26,0.198 10 false d 0.115,0.073 0.438,0.24 0.323,0.167 10 false *A

Text in Illustration
*A Back Side - -
*1 Adhesive - -

Standard Dimension:
Area Dimension
a 5.0 mm (0.197 in.)
b 8.0 mm (0.315 in.)
c 26.9 mm (1.06 in.)
d 5.0 mm (0.197 in.)




e.

Install the back door glass sub-assembly.

i.
B296206E02
1.667,0.51 1.448,0.51 1.448,0.51 1.448,0.885 true 1.656,0.781 1.448,0.781 false 1.365,0.896 1.615,1.104 0.25,0.208 10 false *1

Using suction cups, position the back door glass so that the matchmarks are aligned, and press it in gently along the rim.

Text in Illustration
*1 Matchmark

NOTICE:
·

Check that the back window glass clips are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and back door glass.




ii.

Lightly press the front surface of the back door glass to ensure a close fit.

HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the back door glass using protective tape until the applied adhesive becomes hard.

NOTICE:

Do not drive the vehicle for the time described in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




f.

Connect each connector.


Hide 5. INSPECT FOR LEAKS AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 6.INSTALL REAR SPOILER ASSEMBLY

Hide 67761A 7.INSTALL BACK DOOR TRIM COVER

Hide 67750 8.INSTALL BACK DOOR TRIM BOARD ASSEMBLY