These DTCs are stored when the low beam headlights do not illuminate, or a malfunction is detected in the communication between the headlight assembly and main body ECU (multiplex network body ECU).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2430 | LED headlight LH circuit malfunction | ·
Headlight LED unit assembly LH ·
H-LP Relay ·
Instrument panel junction block assembly ·
Main body ECU (multiplex network body ECU) ·
Harness or connector |
| B2431 | LED headlight RH circuit malfunction | ·
Headlight LED unit assembly RH ·
H-LP Relay ·
Instrument panel junction block assembly ·
Main body ECU (multiplex network body ECU) ·
Harness or connector |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Clear the DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| Both DTC B2430 and B2431 are not output. | A |
| Both DTC B2430 and B2431 are output. | B |
| DTC B2430 or B2431 is output. | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Remove the H-LP relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Voltage not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Voltage applied between terminals 1 and 2 | Below 1 Ω |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connector | Condition | Specified Condition |
|---|---|---|
| Relay terminal 1 - Body ground | Power switch off | 11 to 14 V |
| Relay terminal 5 - Body ground | Power switch off | 11 to 14 V |
OK
NG
Disconnect the A69 headlight assembly LH connector.
Disconnect the A68 headlight assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 3 - A69-4 (LO) | Always | Below 1 Ω |
| Relay terminal 3 - A68-4 (LO) | Always | Below 1 Ω |
| Relay terminal 3 - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the 3C instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 2 - 3C-18 | Always | Below 1 Ω |
| Relay terminal 2 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3C-18 - MB-15 (HRLY) | Always | Below 1 Ω |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
OK
NG
Disconnect the A69 headlight assembly connector or the A68 headlight assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A69-4 (LO) - Body ground | Power switch off, light control switch in head position | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A68-4 (LO) - Body ground | Power switch off, light control switch in head position | 11 to 14 V |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A69-2 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A68-2 (E) - Body ground | Always | Below 1 Ω |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A69-1 (S) - Body ground | Power switch on (IG), light control switch in head position | 9.5 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A68-1 (S) - Body ground | Power switch on (IG), light control switch in head position | 9.5 to 14 V |
OK
NG
Replace the headlight LED unit assembly with a new or known good one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY).
Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).
DTC B2430 and B2431 are not output.
OK
NG
Disconnect the G60 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G60-24 (LLEW) - A69-1 (S) | Always | Below 1 Ω |
| G60-24 (LLEW) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G60-21 (RLEW) - A68-1 (S) | Always | Below 1 Ω |
| G60-21 (RLEW) - Body ground | Always | 10 kΩ or higher |
OK
NG