Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2017.06
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278196 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B1244  Light Sensor Circuit  


DESCRIPTION

The automatic light control sensor detects ambient light. The sensor creates an electrical signal based on the amount of light detected, and sends the signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) turns on or off the headlights and taillights according to the signal. The main body ECU (multiplex network body ECU) stores DTC B1244.

DTC No. DTC Detecting Condition Trouble Area
B1244
·

Malfunction in automatic light control sensor

·

Open or short in automatic light control sensor circuit


·

Automatic light control sensor

·

Harness or connector

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

E144299E56
0.542,2.646 1.021,2.948 0.479,0.302 10 false G90 0.521,2.813 2.594,3.031 2.073,0.219 10 false Automatic Light Control Sensor 4.865,2.844 6.5,3.323 1.635,0.479 10 false Main Body ECU (Multiplex Network Body ECU) 4.865,2.677 5.427,3 0.563,0.323 10 false G59 1.604,0.844 2,1 0.396,0.156 10 false CLTB 1.573,1.521 1.969,1.677 0.396,0.156 10 false CLTS 1.583,2.219 1.979,2.375 0.396,0.156 10 false CLTE 2.063,0.75 2.219,0.927 0.156,0.177 10 false 3 2.073,1.406 2.323,1.625 0.25,0.219 10 false 4 2.063,2.063 2.292,2.313 0.229,0.25 10 false 5 5.031,0.813 5.427,0.969 0.396,0.156 10 false CLTB 5.052,2.188 5.448,2.344 0.396,0.156 10 false CLTE 5.042,1.531 5.438,1.688 0.396,0.156 10 false CLTS 4.781,0.75 5.031,0.958 0.25,0.208 10 false 20 4.771,2.073 5.083,2.354 0.313,0.281 10 false 22 4.781,1.406 5.104,1.667 0.323,0.26 10 false 21

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Illumination Rate Info Illumination rate information 0.00 ms. to 2162.65 ms. Value is output according to ambient light levels -

OK:

Normal conditions listed above are displayed.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
2.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the G90 automatic light control sensor connector.


b.

Disconnect the G59 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G90-3 (CLTB) - G59-20 (CLTB) Always Below 1 Ω
G90-4 (CLTS) - G59-21 (CLTS) Always Below 1 Ω
G90-5 (CLTE) - G59-22 (CLTE) Always Below 1 Ω
G90-3 (CLTB) or G59-20 (CLTB) - Body ground Always 10 kΩ or higher
G90-4 (CLTS) or G59-21 (CLTS) - Body ground Always 10 kΩ or higher
G90-5 (CLTE) or G59-22 (CLTE) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
E173035C55
1.531,0.563 1.958,0.854 0.427,0.292 1.031,2.688 2.083,2 false 2.438,2.708 2.438,2 false 0.125,0.115 0.583,0.417 0.458,0.302 10 false *a 0.854,2.75 1.333,2.969 0.479,0.219 10 false CLTE 2.229,2.75 3,3.063 0.771,0.313 10 false CLTB 1.604,0.635 2.063,0.833 0.458,0.198 10 false G59
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))


a.

Connect the G59 main body ECU (multiplex network body ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G59-20 (CLTB) - G59-22 (CLTE) Power switch off Below 1 V
Power switch on (IG) 11 to 14 V




OK

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR
a.

Remove the automatic light control sensor.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC LIGHT CONTROL SENSOR>REMOVAL


b.

Inspect the automatic light control sensor.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC LIGHT CONTROL SENSOR>ON-VEHICLE INSPECTION



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR