Home › Engine / Hybrid System › 1NZ-FXE INTAKE / EXHAUST › EXHAUST MANIFOLD › from 2017.06
RM2170E _51 Engine / Hybrid System _057008 1NZ-FXE INTAKE / EXHAUST _0277969 EXHAUST MANIFOLD A

1NZ-FXE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 2.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 17141 3.INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

a.

Set a new gasket to the cylinder head sub-assembly.


b.

Temporarily install the exhaust manifold (TWC: Front Catalyst) with the 3 bolts and 2 nuts.


c.

Temporarily install the manifold support bracket with the 3 bolts.


d.
A267694E03
1.604,0.229 1.771,0.396 0.167,0.167 10 true *1 0.604,1.458 0.771,1.625 0.167,0.167 10 true *1 2.573,1.448 2.74,1.615 0.167,0.167 10 true *1 3.156,0.333 3.323,0.5 0.167,0.167 10 true *2 0.146,0.365 0.313,0.531 0.167,0.167 10 true *2

Tighten the 3 bolts and 2 nuts.

Text in Illustration
*1 Bolt
*2 Nut

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


e.

Connect the wire harness clamp and heated oxygen sensor connector.


f.

Remove the 3 bolts and manifold support bracket.


Hide 25611A 4.INSTALL NO. 1 EGR PIPE

a.

Install a new gasket.


b.

Install the No. 1 EGR pipe with the bolt and nut.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 25591 5.INSTALL MANIFOLD SUPPORT BRACKET

a.
U159060E03
0.385,0.146 0.51,0.292 0.125,0.146 10 false A 1.885,0.302 2.01,0.448 0.125,0.146 10 false B 2.635,0.417 2.76,0.563 0.125,0.146 10 false A 3.021,1.25 3.146,1.396 0.125,0.146 10 false A

Install the manifold support bracket with the 4 bolts.

Torque:
Bolt A : 44 N*m (449 kgf*cm, 32 ft.*lbf)
Bolt B : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17167 6.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 17410 8.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (w/ Exhaust Heat Recirculation System)

NOTICE:

When installing the heater water hose, ensure that the exhaust heat recirculation system is filled with coolant. Otherwise, the engine water pump assembly may be damaged.


a.
A077857

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length (Front) 41.5 mm (1.64 in.)
Minimum Free Length (Rear) 38.5 mm (1.52 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install 2 new gaskets to the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).


c.
A181728C59
2.927,1.438 2.802,1.438 2.802,1.438 2.5,1.75 false 1.656,3.219 2.031,3.219 2.031,3.219 2.031,2.438 false 1.458,0.656 1.813,0.656 1.813,0.656 1.813,1.115 false 1.313,0.563 1.604,0.781 0.292,0.219 10 false *1 3.031,1.333 3.313,1.542 0.281,0.208 10 false *a 1.438,3.146 1.76,3.385 0.323,0.24 10 false *2
*1 Exhaust Manifold (TWC: Front Catalyst) or Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in each gasket until its surface is flush with the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gaskets.

·

Do not damage the gaskets.

·

Do not push in the gaskets by using the exhaust pipes when connecting them.




d.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 3 exhaust pipe supports.


e.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold (TWC: Front Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C18
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Exhaust Manifold (TWC: Front Catalyst)
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.



f.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the tail exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258966C30
1.365,0.938 1.094,0.406 1.094,0.406 0.896,0.406 false 1.333,1.167 1.125,1.51 1.125,1.51 0.938,1.51 false 2.24,0.948 2.625,0.448 2.625,0.448 2.823,0.448 true 0.719,0.323 0.875,0.469 0.156,0.146 10 false *1 0.76,1.427 0.917,1.573 0.156,0.146 10 false *2 2.844,0.365 3,0.51 0.156,0.146 10 false *3 0.625,1.74 0.823,2 0.198,0.26 10 false *a
*1 Tail Exhaust Pipe Assembly
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the front exhaust pipe assembly (TWC: Rear Catalyst) and tail exhaust pipe assembly is consistent front-to-rear and left-to-right.



g.

Connect the 2 heater water hoses and slide the 2 clips to secure them.


Hide 17410 9.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (w/o Exhaust Heat Recirculation System)

a.
A077857

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length (Front) 41.5 mm (1.64 in.)
Minimum Free Length (Rear) 38.5 mm (1.52 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install 2 new gaskets to the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).


c.
A181728C59
2.927,1.438 2.802,1.438 2.802,1.438 2.5,1.75 false 1.656,3.219 2.031,3.219 2.031,3.219 2.031,2.438 false 1.458,0.656 1.813,0.656 1.813,0.656 1.813,1.115 false 1.313,0.563 1.604,0.781 0.292,0.219 10 false *1 3.031,1.333 3.313,1.542 0.281,0.208 10 false *a 1.438,3.146 1.76,3.385 0.323,0.24 10 false *2
*1 Exhaust Manifold (TWC: Front Catalyst) or Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in each gasket until its surface is flush with the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gaskets.

·

Do not damage the gaskets.

·

Do not push in the gaskets by using the exhaust pipes when connecting them.




d.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 3 exhaust pipe supports.


e.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold (TWC: Front Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C18
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Exhaust Manifold (TWC: Front Catalyst)
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.



f.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the tail exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258966C30
1.365,0.938 1.094,0.406 1.094,0.406 0.896,0.406 false 1.333,1.167 1.125,1.51 1.125,1.51 0.938,1.51 false 2.24,0.948 2.625,0.448 2.625,0.448 2.823,0.448 true 0.719,0.323 0.875,0.469 0.156,0.146 10 false *1 0.76,1.427 0.917,1.573 0.156,0.146 10 false *2 2.844,0.365 3,0.51 0.156,0.146 10 false *3 0.625,1.74 0.823,2 0.198,0.26 10 false *a
*1 Tail Exhaust Pipe Assembly
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the front exhaust pipe assembly (TWC: Rear Catalyst) and tail exhaust pipe assembly is consistent front-to-rear and left-to-right.



Hide 25680 10.INSTALL EGR COOLER ASSEMBLY

Hide 11.INSPECT FOR EXHAUST GAS LEAK