Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) J

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  ECM Power Source Circuit  


DESCRIPTION

When the power switch is turned to on (IG), auxiliary battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil of the No. 1 integration relay (EFI-MAIN relay), closing the contact and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

A410574E02
5.854,0.646 6.375,0.958 0.521,0.313 10 false IG2D 5.677,0.521 5.833,0.719 0.156,0.198 10 false 9 4.979,1 5.375,1.302 0.396,0.302 10 false G77 4.979,1.188 7.094,1.677 2.115,0.49 10 false Certification ECU (Smart Key ECU Assembly) 3.396,1.385 3.552,1.583 0.156,0.198 10 false 3 3.469,1.635 3.781,1.833 0.313,0.198 10 false 2D 3.906,1.938 4.219,2.135 0.313,0.198 10 false 2D 3.938,1.74 4.094,1.938 0.156,0.198 10 false 4 4.5,2.135 5.583,2.438 1.083,0.302 10 false IG2 NO. 2 5.552,1.948 6.01,2.146 0.458,0.198 10 false A40 5.594,1.719 5.906,1.917 0.313,0.198 10 false 37 5.906,1.823 6.521,2.021 0.615,0.198 10 false IGSW 5.552,2.823 6.01,3.021 0.458,0.198 10 false A40 5.625,2.625 5.781,2.823 0.156,0.198 10 false 3 5.896,2.813 6.323,3.104 0.427,0.292 10 false +B2 5.552,3.271 5.927,3.542 0.375,0.271 10 false A40 5.615,3.073 5.771,3.271 0.156,0.198 10 false 2 5.917,3.25 6.229,3.448 0.313,0.198 10 false +B 5.573,3.698 6.031,3.896 0.458,0.198 10 false A40 5.604,3.51 5.917,3.708 0.313,0.198 10 false 46 5.906,3.698 6.521,3.896 0.615,0.198 10 false MREL 5.552,4.229 6.01,4.427 0.458,0.198 10 false C10 5.594,4.031 5.906,4.229 0.313,0.198 10 false 16 5.906,4.24 6.219,4.438 0.313,0.198 10 false E1 6.302,4.635 6.76,4.833 0.458,0.198 10 false ECM 2.031,4.469 3.958,4.969 1.927,0.5 10 false No. 1 Integration Relay 2.625,4 3.448,4.354 0.823,0.354 10 false EFI-MAIN 3.896,3.698 4.208,3.896 0.313,0.198 10 false 2C 3.927,3.5 4.083,3.698 0.156,0.198 10 false 3 3.896,3.271 4.208,3.469 0.313,0.198 10 false 2C 3.948,3.063 4.104,3.26 0.156,0.198 10 false 4 2.854,2.656 3.313,2.854 0.458,0.198 10 false IG2 2.115,2.083 2.573,2.281 0.458,0.198 10 false IG2 1.906,3.448 2.625,3.708 0.719,0.26 10 false EFI-MAIN 1.542,3.698 1.854,3.896 0.313,0.198 10 false 2C 1.594,3.479 1.75,3.677 0.156,0.198 10 false 2 1.542,2.354 1.854,2.552 0.313,0.198 10 false 2D 1.573,2.177 1.729,2.375 0.156,0.198 10 false 2 1.531,1.938 1.844,2.135 0.313,0.198 10 false 2E 1.563,1.719 1.719,1.917 0.156,0.198 10 false 1 0.844,2.125 1.156,2.448 0.313,0.323 10 false P/I 0.479,3.969 0.958,4.26 0.479,0.292 10 false MAIN 0.563,4.75 1.802,5.094 1.24,0.344 10 false Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C10-16 (E1) - Body ground Always Below 1 Ω




OK

2.CHECK TERMINAL VOLTAGE (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (IGSW VOLTAGE)
a.
U158929E05
1.854,1.375 1.708,1.927 false 0.708,0.115 0.875,0.292 0.167,0.177 10 false *a 0.604,1.104 0.979,1.396 0.375,0.292 10 false A40 1.521,1.938 2.021,2.146 0.5,0.208 10 false IGSW

Disconnect the ECM connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A40-37 (IGSW) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

3.INSPECT NO. 1 INTEGRATION RELAY (EFI-MAIN RELAY)

NG

6.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
3.INSPECT NO. 1 INTEGRATION RELAY (EFI-MAIN RELAY)
a.

Inspect the No. 1 integration relay (EFI-MAIN relay).

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>INTEGRATION RELAY>INSPECTION



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (EFI-MAIN RELAY)

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay and ENG W/PMP relay from the No. 2 engine room relay block and No. 2 junction block assembly.

HINT:

Remove the ENG W/PMP relay connected between the checked terminals as the coil inside the relay influences the measurement value.



b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-4 - A40-2 (+B) Always Below 1 Ω
2C-4 - A40-3 (+B2) Always Below 1 Ω
2C-3 - A40-46 (MREL) Always Below 1 Ω
2C-4 or A40-2 (+B) - Body ground Always 10 kΩ or higher
2C-4 or A40-3 (+B2) - Body ground Always 10 kΩ or higher
2C-3 or A40-46 (MREL) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-2 - Body ground Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
a.

Inspect the No. 1 integration relay (IG2 relay).

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>INTEGRATION RELAY>INSPECTION



OK

7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (IG2 RELAY)

7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-4 - A40-37 (IGSW) Always Below 1 Ω
2D-4 or A40-37 (IGSW) - Body ground Always 10 kΩ or higher




OK

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)
a.
U158980E02
0.823,1.313 1.146,1.479 0.323,0.167 10 false 2E 0.167,0.083 0.406,0.229 0.24,0.146 10 false *a

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2E-1 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Integration Relay)



OK

9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - NO. 1 INTEGRATION RELAY)

9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-2 - Body ground Always Below 1 Ω




OK

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)
a.

Disconnect the Certification ECU (smart key ECU assembly) connector.


b.

Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G77-9 (IG2D) - 2D-3 Always Below 1 Ω
G77-9 (IG2D) or 2D-3 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR