Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0607  Control Module Performance  


MONITOR DESCRIPTION

The ECM continuously monitors its internal processors (CPUs) and heated oxygen sensor transistors. This self-check ensures that the ECM is functioning properly.

DTC No. DTC Detection Condition Trouble Area
P0607
·

The ECM CPUs malfunction.

·

The heated oxygen sensor transistor (built into the ECM) malfunctions.


·

ECM

·

Heated oxygen sensor (sensor 2)

·

Exhaust gas leak



MONITOR STRATEGY

Required Sensors/Components (Main) ECM
Required Sensors/Components (Related) Heated oxygen sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A259532E43
2.458,2.885 2.094,3.323 false 5.25,2.927 5.938,3.302 0.688,0.375 10 false 5 minutes or more 6.208,3.406 6.406,3.594 0.198,0.188 10 false [I] 1.719,2.281 1.958,2.51 0.24,0.229 10 false [B] 2.021,2.281 2.302,2.5 0.281,0.219 10 false [C] 2.385,2.031 2.646,2.219 0.26,0.188 10 false [D] 2.833,2.031 3.094,2.24 0.26,0.208 10 false [E] 3.271,2.031 3.479,2.24 0.208,0.208 10 false [F] 0.646,2.146 1.094,2.354 0.448,0.208 10 false Idling 1.76,3.354 2.417,3.542 0.656,0.188 10 false 2 minutes 4.031,0.979 4.25,1.188 0.219,0.208 10 false [G] 5.448,0.99 5.667,1.198 0.219,0.208 10 false [H] 3.125,2.958 3.688,3.146 0.563,0.188 10 false 1 minute 0.708,2.958 2.24,3.135 1.531,0.177 10 false 30 minutes or more 1.365,2.552 1.646,2.792 0.281,0.24 10 false [A] 0.479,1.135 1.156,1.323 0.677,0.188 10 false 80 km/h 0.49,1.531 1.115,1.729 0.625,0.198 10 false 56 km/h 0.219,2.396 1.083,2.813 0.865,0.417 10 false Power Switch on (IG)

1.

Stop the engine for 30 minutes or more [A].

2.

Connect the GTS to the DLC3.

3.

Turn the power switch on (IG) and turn the GTS on [B].

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) and turn the GTS on [C].

7.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

8.

Start the engine and wait 2 minutes [D].

9.

Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher [E].

10.

Idle the engine for 1 minute [F].

11.

Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


12.

Drive the vehicle at 56 to 80 km/h (35 to 50 mph) for 5 minutes or more [H].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


13.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [I].

14.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

16.

Input the DTC: P0607, P0136, P0137 or P0138.

17.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [I] again.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0607)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0607 and P0136, P0137 or P0138 are output A
DTC P0607 is output B



A

2.INSPECT DTC (DTC P0136, P0137 OR P0138)

B

3.CHECK FOR EXHAUST GAS LEAK
2.INSPECT DTC (DTC P0136, P0137 OR P0138)
a.

Refer to the P0136, P0137 or P0138 flowchart.

HINT:
·

If P0136 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0136

·

If P0137 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0136

·

If P0138 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0136

·

If DTC P0607 and P0136, P0137 or P0138 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or higher).





NEXT

6.INSPECT ECM
3.CHECK FOR EXHAUST GAS LEAK
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine.


f.

Allow the engine to idle, and then rev the engine.


g.

Check for exhaust gas leaks around the heated oxygen sensor.

If any exhaust gas leaks are present, repair them and proceed to "Perform Confirmation Driving Pattern". If no exhaust gas leaks are present, proceed to "Perform Confirmation Driving Pattern".

HINT:
·

If no exhaust gas leaks are present, there may be a malfunction in the heated oxygen sensor circuit.

·

If any exhaust gas leaks are present around the heated oxygen sensor, noise appears in the output voltage of the heated oxygen sensor.

·

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION





NEXT

4.PERFORM CONFIRMATION DRIVING PATTERN
4.PERFORM CONFIRMATION DRIVING PATTERN
A144392E74
0.03,0.27 3.371,0.433 3.341,0.163 10 Engine Coolant Temperature: 75°C or higher 1.793,0.928 2.046,1.105 0.253,0.177 10 80 1.793,1.313 2.046,1.496 0.253,0.184 10 60 1.659,0.62 2.037,0.804 0.378,0.184 10 km/h 1.922,2.453 2.036,2.609 0.114,0.156 10 0 6.361,2.442 6.721,2.597 0.361,0.156 10 Time 4.546,0.858 5.188,1.014 0.642,0.156 10 5 minutes 4.081,1.189 4.081,0.828 false 5.656,1.189 5.656,0.828 false 4.511,0.914 4.081,0.914 false 5.192,0.914 5.656,0.914 false


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


f.

Start the engine.


g.

Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher.


h.

Perform the driving pattern.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


i.

Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle.


ii.

Drive the vehicle between 60 and 80 km/h (37 and 50 mph) for 5 minutes.



i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Result
Result Proceed to
DTC P0136, P0137, P0138 and/or P0607 are output A
Only P0607 is output B
DTCs are not output C



A

5.INSPECT DTC (DTC P0136, P0137 OR P0138)

B

C

6.INSPECT ECM
5.INSPECT DTC (DTC P0136, P0137 OR P0138)
a.

Refer to the P0136, P0137 or P0138 flowchart.

HINT:
·

If P0136 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0136

·

If P0137 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0136

·

If P0138 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0136

·

If DTC P0607 and P0136, P0137 or P0138 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or higher).





NEXT

6.INSPECT ECM
6.INSPECT ECM

b.

Stop the engine and wait for 30 minutes.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Turn the GTS on.


f.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


g.

Start the engine and allow it to idle for 2 minutes.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Result
Result Proceed to
DTCs are not output A
DTC P0607 is output B



A

END

B