Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0136  O2 (A/F) Sensor Circuit (Bank 1 Sensor 2)  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0138  Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)  P0139  Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 2)  P013A  Oxygen Sensor Slow Response - Rich to Lean Bank 1 Sensor 2  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC (Three-Way Catalytic Converter) is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric air fuel level. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is high. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is lean (low voltage, i.e. less than 0.45 V).

Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas is low. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the TWC is rich or lean, and adjusts the fuel injection duration accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.

A254107E17
0.885,3.01 0.583,3.01 false 3.375,1.042 3.115,1.281 true 3.427,1.646 2.885,1.646 true 3.427,1.333 2.865,1.51 true 3.427,2.24 2.906,2.094 false 3.427,2.542 2.771,2.313 true 3.427,2.823 2.875,2.51 false 2.25,2.76 1.698,3.073 true 0.167,2.906 0.594,3.073 0.427,0.167 10 false Cover 1.24,3.073 2.125,3.25 0.885,0.177 10 false Exhaust Gas 1.792,0.885 2.646,1.083 0.854,0.198 10 false Atmosphere 3.396,0.948 3.979,1.156 0.583,0.208 10 false Housing 3.448,1.271 4.688,1.438 1.24,0.167 10 false Platinum Electrode 3.448,1.573 4.667,1.927 1.219,0.354 10 false Solid Electrolyte (Zirconia Element) 3.448,2.469 3.958,2.646 0.51,0.177 10 false Heater 3.448,2.75 4.635,2.958 1.188,0.208 10 false Coating (Ceramic) 3.448,2.167 4.688,2.333 1.24,0.167 10 false Platinum Electrode 4.115,0.948 5.094,1.146 0.979,0.198 10 false Output Voltage 4.802,2.927 6.844,3.146 2.042,0.219 10 false Richer - Air fuel Ratio - Leaner 5.115,0.792 6.479,1 1.365,0.208 10 false Ideal Air fuel Mixture

DTC No. DTC Detection Condition Trouble Area
P0136 Either of the following conditions is met:
·

Abnormal voltage output:

During active air fuel ratio control, heated oxygen sensor voltage does not increase to 0.69 V or higher for certain period of time (2 trip detection logic)


·

Low impedance:

Sensor impedance less than 5 Ω for 30 seconds or more when ECM presumes sensor is warmed up and operating normally (2 trip detection logic)



·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

PCV valve and hose

·

Intake system

·

EGR valve assembly


P0137 Either of the following conditions is met:
·

Low voltage (open):

During active air fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic)

(a) Heated oxygen sensor voltage output less than 0.21 V

(b) Target air fuel ratio rich



·

High impedance:

Sensor impedance 15 kΩ or higher for 90 seconds or more when ECM presumes sensor to be warmed up and operating normally (2 trip detection logic)



·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system

·

EGR valve assembly


P0138
·

Extremely high voltage (short):

Heated oxygen sensor voltage output exceeds 1.2 V for 10 seconds or more (2 trip detection logic)



·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

ECM


P0139 Heated oxygen sensor (sensor 2) voltage does not drop to less than 0.2 V immediately after fuel cut starts (2 trip detection logic)
·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Gas leak from exhaust system

·

EGR valve assembly


P013A Heated oxygen sensor (sensor 2) voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut status (1 trip detection logic)
·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Gas leak from exhaust system

·

EGR valve assembly



MONITOR DESCRIPTION

Active Air fuel Ratio Control


The ECM usually performs air fuel ratio feedback control so that the air fuel ratio sensor output indicates a near stoichiometric air fuel level. This vehicle includes active air fuel ratio control in addition to regular air fuel ratio control. The ECM performs active air fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and heated oxygen sensor malfunctions (refer to the diagram below).

Active air fuel ratio control is performed for approximately 30 seconds while driving with a warm engine. During active air fuel ratio control, the air fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Abnormal Voltage Output of Heated Oxygen Sensor (DTC P0136)


While the ECM is performing active air fuel ratio control, the air fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the heated oxygen sensor voltage does not increase to 0.69 V or higher during active air fuel ratio control, the ECM determines that the sensor voltage output is abnormal and stores DTC P0136.

A152942E38
0.068,0.052 4.982,0.259 4.913,0.208 10 Heated Oxygen Sensor Circuit Malfunction (P0136: Abnormal Voltage) 4.724,1.259 5.416,1.432 0.693,0.173 10 Operation 4.237,0.755 5.924,0.911 1.687,0.156 10 Approximately 30 seconds 3.335,1.568 3.852,1.751 0.517,0.184 10 Normal 2.178,1.357 2.521,1.534 0.343,0.177 10 OFF 2.087,2.126 2.548,2.296 0.461,0.170 10 0.69 V 2.087,2.892 2.548,3.068 0.461,0.177 10 0.21 V 3.166,2.541 3.850,2.725 0.684,0.184 10 Abnormal 2.97,2.091 3.152,1.624 false 3.152,1.624 3.292,1.624 false 2.794,2.303 2.921,2.604 false 2.921,2.604 3.11,2.604 false 0.052,1.329 1.917,1.520 1.864,0.191 10 Active air fuel ratio control 0.051,2.528 2.015,2.719 1.964,0.191 10 Heated oxygen sensor voltage


Open in Heated Oxygen Sensor Circuit (DTC P0137)


During active air fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air fuel ratio to become rich or lean.

If the heated oxygen sensor has an open circuit, or the voltage output of the sensor noticeably decreases, the OSC indicates an extraordinarily high value. Even if the ECM attempts to continue regulating the air fuel ratio to become rich or lean, the heated oxygen sensor output does not change.

While performing active air fuel ratio control, when the target air fuel ratio is rich and the heated oxygen sensor voltage output is less than 0.21 V (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137.

HINT:

*: The TWC has the capability to store oxygen. The OSC and the emission purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated, based on the calculated OSC value.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0420


A234468E23
0.066,0.046 3.993,0.255 3.928,0.209 10 Heated Oxygen Sensor Circuit Low Voltage (P0137: Open) 0.283,1.213 1.175,1.552 0.892,0.339 10 Active air fuel ratio control 0.297,3.203 1.566,3.563 1.269,0.359 10 Heated oxygen sensor voltage 0.283,2.078 1.552,2.280 1.269,0.202 10 Target air fuel ratio 1.974,2.027 2.928,2.395 0.953,0.368 10 Stoichiometric Air Fuel Level 2.783,1.306 3.149,1.508 0.367,0.202 10 OFF 2.492,3.469 2.979,3.671 0.487,0.202 10 0.21 V 4.519,1.274 5.283,1.476 0.764,0.202 10 Operation 4.658,1.636 5.224,1.838 0.565,0.202 10 Normal 5.683,1.616 6.328,1.818 0.646,0.202 10 Abnormal 6.058,4.057 6.794,4.259 0.737,0.202 10 Abnormal 6.055,2.47 6.620,2.672 0.565,0.202 10 Normal 4.782,2.408 5.147,2.610 0.366,0.202 10 Rich 5.815,3.761 6.025,4.024 false 4.292,2.016 4.453,1.724 false 4.453,1.724 4.591,1.724 false 5.342,2.366 5.443,1.715 false 5.443,1.715 5.628,1.715 false 5.693,2.983 5.843,2.554 false 5.843,2.554 6.001,2.554 false 4.003,0.298 5.649,0.653 1.647,0.355 10 Approximately 30 seconds


High or Low Impedance of Heated Oxygen Sensor (DTC P0136 or P0137)


A076841E52
1.167,1.229 1.531,0.781 1.531,0.781 0.854,2.49 false 0.052,0.052 2.792,0.417 2.74,0.365 10 false Relationship between element temperature and impedance: 1.573,0.677 2.875,0.875 1.302,0.198 10 false DTC Detection Area 1.385,3.156 1.875,3.354 0.49,0.198 10 false °C (°F) 0.135,0.833 0.375,1.031 0.24,0.198 10 false (Ω) 0.208,1.229 0.646,1.427 0.438,0.198 10 false 15000 0.281,1.5 0.646,1.698 0.365,0.198 10 false 1000 0.354,1.865 0.625,2.063 0.271,0.198 10 false 100 0.448,2.25 0.646,2.448 0.198,0.198 10 false 10 0.5,2.385 0.625,2.583 0.125,0.198 10 false 5 0.531,2.698 0.802,2.896 0.271,0.198 10 false 300 0.469,2.906 0.833,3.104 0.365,0.198 10 false (572) 0.958,2.698 1.229,2.896 0.271,0.198 10 false 400 0.896,2.906 1.26,3.104 0.365,0.198 10 false (752) 1.396,2.698 1.667,2.896 0.271,0.198 10 false 500 1.313,2.906 1.677,3.104 0.365,0.198 10 false (932) 1.885,2.698 2.156,2.896 0.271,0.198 10 false 600 1.74,2.906 2.198,3.104 0.458,0.198 10 false (1112) 2.906,2.698 3.177,2.896 0.271,0.198 10 false 800 2.781,2.906 3.427,3.427 0.646,0.521 10 true (1472) 2.396,2.698 2.667,2.896 0.271,0.198 10 false 700 2.26,2.906 2.719,3.104 0.458,0.198 10 false (1292)

During normal air fuel ratio feedback control, there are small variations in the exhaust gas oxygen concentration. In order to continuously monitor the slight variation of the heated oxygen sensor signal while the engine is running, the impedance* of the sensor is measured by the ECM. The ECM determines that there is a malfunction in the sensor when the measured impedance deviates from the standard range.

*: The effective resistance in an alternating current electrical circuit.

HINT:
·

The impedance cannot be measured using an ohmmeter.

·

DTC P0136 indicates the deterioration of the heated oxygen sensor. The ECM stores the DTC by calculating the impedance of the sensor when the typical enabling conditions are satisfied (2 driving cycles).

·

DTC P0137 indicates an open or short circuit in the heated oxygen sensor (2 driving cycles). The ECM stores the DTC when the impedance of the sensor exceeds the threshold 15 kΩ.




Extremely High Output Voltage of Heated Oxygen Sensor (DTC P0138)


The ECM continuously monitors the heated oxygen sensor output voltage while the engine is running.

DTC P0138 is stored if the heated oxygen sensor voltage output is 1.2 V or higher for 10 seconds or more.


Abnormal Voltage Output of Heated Oxygen Sensor during Fuel Cut (DTC P0139)


The sensor output voltage drops to less than 0.2 V (extremely lean status) immediately when the vehicle decelerates and fuel cut is operating. If the voltage does not drop to less than 0.2 V for 6 seconds or more, the ECM determines that the sensor response has deteriorated, illuminates the MIL and stores this DTC.


Abnormal Voltage Output of Heated Oxygen Sensor during Fuel Cut from Rich Condition (DTC P013A)


If the sensor output voltage does not drop from 0.35 to 0.2 V immediately when the vehicle decelerates and fuel cut is operating, the ECM illuminates the MIL and stores this DTC.


MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor
Required Sensors/Components (Related) Crank position sensor
Engine coolant temperature sensor
Mass air flow meter sub-assembly
Throttle position sensor
Air fuel ratio sensor
Frequency of Operation Once per driving cycle: Active air fuel ratio control detection, Heated oxygen sensor abnormal voltage during fuel cut
Continuous: Other

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs are not present P0016 (VVT system - misalignment)
P0031, P0032, P101D (Air fuel ratio sensor heater)
P0037, P0038, P102D (Heated oxygen sensor heater)
P0102, P0103 (Mass air flow meter)
P0107, P0108 (Manifold absolute pressure)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0128 (Thermostat)
P014C, P014D, P015A, P015B, P2195, P2196, P2237, P2238, P2239, P2252, P2253 (Air fuel ratio sensor)
P0171, P0172 (Fuel system)
P0300, P0301, P0302, P0303, P0304 (Misfire)
P0335 (Crank position sensor)
P0340 (Cam position sensor)
P0401(EGR system (Closed))
P0451, P0452, P0453 (EVAP system)
P219A, P219C, P219D, P219E, P219F (Air fuel ratio - Imbalance)

P0136 and P0137: Heated Oxygen Sensor Voltage Check (Voltage Malfunction and Low Voltage)
Auxiliary battery voltage 11 V or higher
Intake air temperature -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [570 mmHg(abs)] or higher
Idle Off
Engine speed Less than 4000 rpm
Air fuel ratio sensor Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 70%

P0136: Heated Oxygen Sensor Circuit Continuity Check (Circuit Short)
Auxiliary battery voltage 11 V or higher
Estimated heated oxygen sensor temperature Less than 700°C (1292°F)

P0137: Heated Oxygen Sensor Circuit Continuity Check (Circuit Open)
Auxiliary battery voltage 11 V or higher
Estimated heated oxygen sensor temperature 450°C (842°F) or higher, and less than 750°C (1382°F)

P0138: Heated Oxygen Sensor Circuit Continuity Check (Out of Range)
Auxiliary battery voltage 11 V or higher
Time after engine start 2 seconds or more

P0139: Heated Oxygen Sensor Response Rate during Fuel Cut
Engine coolant temperature 75°C (167°F) or higher
Estimated catalyst temperature 400°C (752°F) or higher
Fuel cut On

P013A: Heated Oxygen Sensor Response Rate during Fuel Cut from Rich Condition
Auxiliary battery voltage 11 V or higher
Engine coolant temperature 75°C (167°F) or higher
Estimated catalyst temperature 400°C (752°F) or higher
Fuel cut On

TYPICAL MALFUNCTION THRESHOLDS

P0136: Heated Oxygen Sensor Voltage Check (Voltage Malfunction)
All of the following conditions are met (a), (b) and (c)
(a) OSC (Oxygen Storage Capacity) of catalyst 2.1 g or more
(b) Commanded air fuel ratio 14.4 or less
(c) Heated oxygen sensor voltage 0.21 V or higher, and less than 0.69 V

P0137: Heated Oxygen Sensor Voltage Check (Low Voltage)
All of the following conditions are met (a), (b) and (c)
(a) OSC (Oxygen Storage Capacity) of catalyst 2.1 g or more
(b) Commanded air fuel ratio 14.4 or less
(c) Heated oxygen sensor voltage Less than 0.21 V

P0136: Heated Oxygen Sensor Circuit Continuity Check (Circuit Short)
Duration of following condition 30 seconds or more
Heated oxygen sensor impedance Less than 5 Ω

P0137: Heated Oxygen Sensor Circuit Continuity Check (Circuit Open)
Duration of following condition 90 seconds or more
Heated oxygen sensor impedance 15 kΩ or higher

P0138: Heated Oxygen Sensor Circuit Continuity Check (Out of Range)
Duration of following condition 10 seconds or more
Heated oxygen sensor output voltage 1.2 V or higher

P0139: Heated Oxygen Sensor Response Rate during Fuel Cut
Duration until heated oxygen sensor voltage drops to 0.2 V during fuel cut 6 seconds or more

P013A: Heated Oxygen Sensor Response Rate during Fuel Cut from Rich Condition
Duration that heated oxygen sensor voltage drops from 0.35 to 0.2 V during fuel cut (Normalized) 1 or more

CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation driving pattern will activate the heated oxygen sensor monitor (The catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.



P0136, P0137 and P0138

A264212E61
1.74,2.438 1.563,2.802 1.563,2.802 1.417,2.802 false 4.031,0.74 4.281,1 0.25,0.26 10 false [C] 3.49,2.979 4.74,3.25 1.25,0.271 10 false 10 minutes or more 1.094,1.365 1.698,1.604 0.604,0.24 10 false 75 km/h 2.031,2.427 2.26,2.677 0.229,0.25 10 false [A] 1.031,0.49 1.635,0.708 0.604,0.219 10 false 120 km/h 1.25,2.219 1.625,2.49 0.375,0.271 10 false Idling 0.479,2.729 1.375,3.104 0.896,0.375 10 false Power Switch on (IG) 2.646,2.125 2.885,2.365 0.24,0.24 10 false [B] 2.344,2.938 3.167,3.229 0.823,0.292 10 false Warming up 5,3.313 5.24,3.583 0.24,0.271 10 false [D]

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on [A].

6.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

8.

With the shift lever in D, drive the vehicle at 75 to 120 km/h (47 to 75 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0136, P0137 or P0138.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again.




P0139 and P013A

A284467E43
0.188,0.698 1.135,0.854 0.948,0.156 10 false Vehicle Speed 0.656,1.177 1.177,1.333 0.521,0.156 10 false 75 km/h 0.792,2.219 1.167,2.375 0.375,0.156 10 false Idling 0.104,2.417 1.375,2.719 1.271,0.302 10 false Power Switch off 1.469,2.76 2.24,2.948 0.771,0.188 10 false Warming up 2.552,2.76 3.792,2.948 1.24,0.188 10 false 10 minutes or more 1.76,2.115 1.99,2.292 0.229,0.177 10 false [A] 3.063,1.042 3.552,1.219 0.49,0.177 10 false [B]* 4.208,1.042 4.438,1.219 0.229,0.177 10 false [C] 5.198,1.042 5.427,1.219 0.229,0.177 10 false [C] 6.188,1.042 6.417,1.219 0.229,0.177 10 false [C] 4.708,3.135 4.917,3.313 0.208,0.177 10 false [D] 5.708,3.135 5.917,3.313 0.208,0.177 10 false [D] 6.698,3.135 6.906,3.313 0.208,0.177 10 false [D] 0.052,3.365 4.667,3.573 4.615,0.208 10 false *: Drive the vehicle while keeping the engine load as constant as possible.

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.

7.

Check that Catalyst Efficiency / Current is Incomplete.

8.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with the shift lever in P [A].

HINT:

In order to keep the idle stable, turn the A/C and all other electric loads off and do not perform any shift operations.


10.

Drive the vehicle at approximately 75 km/h (47 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


11.

With the shift lever in B, drive the vehicle at 75 km/h (47 mph), and then decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


12.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / RL F/C B1S2 [D].

13.

Check the Test Value for RL F/C B1S2.

HINT:

If Test Value displays 0, perform step [C] until it displays a value larger than 0, as the O2 Sensor monitor is not finished.


14.

Repeat step [C] 2 times or more in one driving cycle.

15.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

18.

Input the DTC: P0139 or P013A.

19.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows INCOMPLETE or N/A, drive the vehicle with the shift lever in B, and then perform step [C] again.




CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the GTS.


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

5.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

6.

Idle the engine for 5 minutes or more with the shift lever in P.

7.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Gas AF Control / AFS Voltage B1S1 and O2S B1S2.

8.

Perform the Control the Injection Volume for A/F Sensor with the engine idling (press the 12.5% or -12.5% button to change the fuel injection volume).

9.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.




Standard
GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E66
5.792,3.625 7.115,3.896 1.323,0.271 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.531,1.594 1.979,1.781 0.448,0.188 8 false 12% 1.479,1.833 1.927,2.021 0.448,0.188 8 false -12% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 4.156,1.594 4.604,1.781 0.448,0.188 8 false 12% 4.115,1.833 4.563,2.021 0.448,0.188 8 false -12% 4.146,3.729 4.594,3.917 0.448,0.188 8 false 12% 4.104,3.917 4.552,4.104 0.448,0.188 8 false -12% 4.104,5.958 4.552,6.146 0.448,0.188 8 false -12% 4.104,8.021 4.552,8.208 0.448,0.188 8 false -12% 4.156,5.74 4.604,5.927 0.448,0.188 8 false 12% 4.156,7.813 4.604,8 0.448,0.188 8 false 12% 1.49,7.813 1.938,8 0.448,0.188 8 false 12% 1.49,5.75 1.938,5.938 0.448,0.188 8 false 12% 1.49,3.688 1.938,3.875 0.448,0.188 8 false 12% 1.438,3.906 1.885,4.094 0.448,0.188 8 false -12% 1.448,5.948 1.896,6.135 0.448,0.188 8 false -12% 1.438,8.021 1.885,8.208 0.448,0.188 8 false -12% 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.125,0.688 0.573,0.938 0.448,0.25 10 false Case 0.792,0.583 2.802,0.969 2.01,0.385 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.5,0.583 5.594,1.031 2.094,0.448 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.969,0.583 7.01,1 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4.031 7.125,4.469 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.635 7.125,5.073 1.323,0.438 10 false - Air fuel ratio sensor circuit 5.917,5.604 6.969,5.979 1.052,0.375 10 false - Heated oxygen sensor 5.927,6.198 6.969,6.625 1.042,0.427 10 false - Heated oxygen sensor heater 5.927,6.792 6.969,7.229 1.042,0.438 10 false - Heated oxygen sensor circuit 5.927,7.469 6.813,7.875 0.885,0.406 10 false - Fuel injector assembly 5.917,8.083 7.073,8.417 1.156,0.333 10 false - Fuel pressure 5.917,8.531 7.01,9.313 1.094,0.781 10 false - Gas leak from exhaust system 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG

·

Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Gas AF Control / AFS Voltage B1S1 and O2S B1S2; and then press the graph button on the Data List view.


NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (DTC P0136, P0137, P0138, P0139 OR P013A)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0138 is output A
DTC P0137 is output B
DTC P0136 is output C
DTC P0139 or P013A is output D
DTC P0136, P0137, P0138, P0139 or P013A and other DTCs are output E

HINT:

If any DTCs other than P0136, P0137, P0138, P0139 or P013A are output, troubleshoot those DTCs first.




A

2.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

B

8.CHECK FOR EXHAUST GAS LEAK

C

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

D

21.CHECK FOR EXHAUST GAS LEAK

E

2.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
A213127E04
1.5,1.76 1.125,1.344 false 2.229,2.354 1.896,2.021 false 1.125,2.354 1.458,2.021 false 0.177,0.125 0.396,0.313 0.219,0.188 10 false *a 0.885,1.188 1.104,1.375 0.219,0.188 10 false +B 2.24,2.354 2.656,2.542 0.417,0.188 10 false OX1B 0.875,2.354 1.094,2.542 0.219,0.188 10 false E2

a.

Disconnect the heated oxygen sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+B) - 4 (E2) Always 10 kΩ or higher
2 (+B) - 3 (OX1B) Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Heated Oxygen Sensor)

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Turn the power switch to off and wait for 5 minutes or more.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C10-22 (HT1B) - C10-103 (OX1B) Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine and warm it up.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Gas AF Control / O2S B1S2.


g.

Change the fuel injection volume using the GTS, and monitor the voltage output of heated oxygen sensor displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The heated oxygen sensor has a maximum output delay of approximately 20 seconds.



Standard voltage:

Fluctuates between 0.4 V or less, and 0.55 V or higher.




OK

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

8.CHECK FOR EXHAUST GAS LEAK
5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Turn the power switch on (IG).


b.

Turn the GTS on.


c.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


d.

Start the engine and warm it up.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Gas AF Control / AFS Voltage B1S1 and O2S B1S2.


f.

Change the fuel injection volume using the GTS, and monitor the voltage output of air fuel ratio and heated oxygen sensors displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1, and the heated oxygen sensor is displayed as O2S B1S2 on the GTS.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result
GTS Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1 (Air fuel ratio) Alternates between higher and less than 3.3 V OK
Remains at higher than 3.3 V NG
Remains at less than 3.3 V NG

HINT:

A normal heated oxygen sensor voltage (O2S B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage (AFS Voltage B1S1) remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606E78
5.885,2.479 6.365,1.396 false 5.552,2.271 6.365,1.396 false 5.708,1.667 6.365,1.396 false 5.563,2.448 5.844,2.667 false 3.021,1.26 2.865,1.677 false 4.333,1.813 4.094,1.688 false 3.573,2.604 3.188,2.917 false 1.958,1.99 2.125,1.99 false 1.958,2.948 2.156,2.948 false 1.531,1.896 1.906,2.052 0.375,0.156 10 false 3.3 V 2.667,0.26 3.083,0.458 0.417,0.198 10 false 12.5% 4.125,1.125 4.781,1.323 0.656,0.198 10 false -12.5% 1.656,2.854 1.906,3.052 0.25,0.198 10 false 1 V 1.667,3.385 1.906,3.583 0.24,0.198 10 false 0 V 3.073,1.146 4,1.344 0.927,0.198 10 false Malfunctioning 5.854,2.615 6.792,2.781 0.938,0.167 10 false Malfunctioning 4.76,0.125 5.823,0.323 1.063,0.198 10 false Injection Volume 3.635,2.51 5.563,2.729 1.927,0.219 10 false Heated Oxygen Sensor Output 6.406,1.125 6.938,1.813 0.531,0.688 10 false Air Fuel Ratio Sensor Output 4.406,1.75 4.906,1.948 0.5,0.198 10 false Normal



OK

6.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

16.REPLACE AIR FUEL RATIO SENSOR
6.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.


g.

Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.





OK

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO (FUEL INJECTOR ASSEMBLY, FUEL SYSTEM, INTAKE SYSTEM, ETC.)

NG

7.INSPECT EGR VALVE ASSEMBLY
7.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO (FUEL INJECTOR ASSEMBLY, FUEL SYSTEM, INTAKE SYSTEM, ETC.)

NG

8.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

9.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

9.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
a.

Inspect the heated oxygen sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>HEATED OXYGEN SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

10.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

10.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-1 (HT1B) - C10-22 (HT1B) Always Below 1 Ω
C16-3 (OX1B) - C10-103 (OX1B) Always Below 1 Ω
C16-4 (E2) - C10-135 (EX1B) Always Below 1 Ω
C16-1 (HT1B) or C10-22 (HT1B) - Body ground Always 10 kΩ or higher
C16-3 (OX1B) or C10-103 (OX1B) - Body ground Always 10 kΩ or higher




OK

11.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.REPLACE HEATED OXYGEN SENSOR
a.

Replace the heated oxygen sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>HEATED OXYGEN SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




NEXT

12.PERFORM CONFIRMATION DRIVING PATTERN
12.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform the Confirmation Driving Pattern (P0136, P0137 and P0138).



NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0137)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0137)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


e.

Input the DTC: P0136 or P0137.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern again but increase the vehicle speed.

Result
Result Proceed to
ABNORMAL
(DTC P0136 or P0137 is output)
A
NORMAL
(DTCs are not output)
B



A

14.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

B

END

14.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.


g.

Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.

·

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION





OK

NG

15.INSPECT EGR VALVE ASSEMBLY
15.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly or air fuel ratio sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

NG

16.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




NEXT

17.PERFORM CONFIRMATION DRIVING PATTERN
17.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform the Confirmation Driving Pattern (P0136, P0137 and P0138).



NEXT

18.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136)
18.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


e.

Input the DTC: P0136.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern again but increase the vehicle speed.

Result
Result Proceed to
ABNORMAL
(DTC P0136 is output)
A
NORMAL
(DTCs are not output)
B



A

19.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

B

END

19.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.


g.

Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.

·

Perform "Inspection After Repair" after replacing the heated oxygen sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION





OK

NG

20.INSPECT EGR VALVE ASSEMBLY
20.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly or heated oxygen sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

NG

21.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

22.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

22.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
a.

Turn the power switch off and wait for 5 minutes or more.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C10-22 (HT1B) - C10-103 (OX1B) Always 10 kΩ or higher




OK

23.PERFORM CONFIRMATION DRIVING PATTERN

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform the Confirmation Driving Pattern (P0139 and P013A).



NEXT

24.READ OUTPUT DTC (DTC P0139 OR P013A IS OUTPUT AGAIN)
24.READ OUTPUT DTC (DTC P0139 OR P013A IS OUTPUT AGAIN)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


e.

Input DTCs: P0139 or P013A.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern again but increase the vehicle speed.

Result
Result Proceed to
ABNORMAL
(DTC P0139 or P013A is output)
A
NORMAL
(DTCs are not output)
B



A

25.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

B

25.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.


g.

Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.

·

Perform "Inspection After Repair" after replacing the heated oxygen sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION





OK

NG

26.INSPECT EGR VALVE ASSEMBLY
26.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly or heated oxygen sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

NG