Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P2118  Throttle Actuator Control Motor Current Range / Performance  


DESCRIPTION

The electronic throttle control system has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (less than 4 V), the ECM determines that there is a malfunction in the electronic throttle control system and cuts off the current to the throttle actuator.

When the voltage becomes unstable, the electronic throttle control system itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the power switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.

HINT:

The electronic throttle control system does not use a throttle cable.


A255382E44
0.031,1.781 0.906,2.156 0.875,0.375 10 false from Auxiliary Battery 0.813,3.51 1.885,3.708 1.073,0.198 10 false Throttle Actuator 4.802,1.698 5.25,1.896 0.448,0.198 10 false +BM 4.802,3.76 5.323,3.958 0.521,0.198 10 false ME01 4.802,2.427 5.115,2.625 0.313,0.198 10 false M+ 4.802,3.073 5.115,3.271 0.313,0.198 10 false M- 5.938,2.479 6.594,3.198 0.656,0.719 10 false Throttle Actuator Control Circuit 4.802,0.927 5.25,1.125 0.448,0.198 10 false +B 0.115,1.01 0.865,1.427 0.75,0.417 10 false from EFI-MAIN Relay 5.938,0.76 6.573,1.479 0.635,0.719 10 false Power Source Circuit for CPU 1.219,1.969 1.625,2.115 0.406,0.146 10 false ETCS 5.635,4.25 5.99,4.417 0.354,0.167 10 false ECM

DTC No. DTC Detection Condition Trouble Area
P2118 An open in the electronic throttle control system power source (+BM) circuit (1 trip detection logic).
·

Open in electronic throttle control system power source circuit

·

Auxiliary battery

·

Auxiliary battery terminals

·

ETCS fuse

·

ECM



MONITOR DESCRIPTION

The ECM monitors the auxiliary battery supply voltage applied to the throttle actuator.

When the power supply voltage (+BM) is less than 4 V for 0.8 seconds or more, the ECM interprets this as an open in the power supply circuit (+BM). The ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Throttle actuator (throttle body with motor assembly)
Throttle valve (throttle body with motor assembly)
ETCS fuse
Required Sensors/Components (Related) -
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored None
Both of the following conditions are met -
Command to electronic throttle actuator power On
Auxiliary battery voltage 8 V or higher

TYPICAL MALFUNCTION THRESHOLDS

Electronic throttle actuator power supply voltage Less than 4 V

COMPONENT OPERATING RANGE

Electronic throttle control Normal

CONFIRMATION DRIVING PATTERN

A410491E01
1.042,0.583 2.135,0.875 1.094,0.292 10 false 2500 rpm 1.344,1.958 2.01,2.25 0.667,0.292 10 false Idling 2.042,2.354 2.365,2.635 0.323,0.281 10 false [A] 3.177,2.281 5,2.677 1.823,0.396 10 false Approximately 5 seconds 3.51,2.813 5.125,3.198 1.615,0.385 10 false 16 seconds or more 4.625,0.458 5.052,0.74 0.427,0.281 10 false [B] 6.01,3.26 6.469,3.458 0.458,0.198 10 false [C] 0.396,2.229 2.365,2.583 1.969,0.354 10 false Power Switch on (IG)

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on [A].

6.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

7.

Start the engine.

8.

Slowly depress the accelerator pedal, raise the engine speed to approximately 2500 rpm over approximately 5 seconds, and then idle the engine [B].

HINT:

During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, perform step [B] after charging control has completed.


9.

Check that 16 seconds or more have elapsed since the engine was started.

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P2118.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.




FAIL-SAFE

When this DTC or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 5.5° throttle angle by the return spring. The ECM stops the engine and the vehicle can be driver using solely the hybrid system. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the power switch is then turned off.

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (+BM VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Gas Throttle / +BM Voltage.


e.

Read the value displayed on the GTS.

Result
Result Proceed to
Less than 4 V A
11 to 16 V B



A

2.CHECK HARNESS AND CONNECTOR (ECM - AUXILIARY BATTERY, BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (ECM - AUXILIARY BATTERY, BODY GROUND)
a.

Disconnect the ECM connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C10-29 (+BM) - Body ground Power switch off 11 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C10-59 (ME01) - Body ground Always Below 1 Ω
C10-16 (E1) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR