Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P2102  Throttle Actuator Control Motor Circuit Low  P2103  Throttle Actuator Control Motor Circuit High  


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.

The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body with motor assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to a request from the hybrid system.

HINT:

This Electronic Throttle Control System (ETCS) does not use a throttle cable.


DTC No. DTC Detection Condition Trouble Area
P2102 Both of the following conditions continue for 2.0 seconds (1 trip detection logic):
(a) The throttle actuator drive duty cycle is 80% or higher.
(b) The throttle actuator current is less than 0.5 A.
·

Open in throttle actuator circuit

·

Throttle actuator

·

ECM


P2103 Either of the following conditions is met (1 trip detection logic):
·

A motor driver IC high current limiter monitor input failure.

·

A motor driver IC high current inhibit signal on.


·

Short in throttle actuator circuit

·

Throttle actuator

·

Throttle valve

·

Throttle body with motor assembly

·

ECM



MONITOR DESCRIPTION

The ECM monitors the electrical current through the electronic actuator, and detects malfunctions and open circuits in the throttle actuator based on this value. If the current is outside the standard range, the ECM determines that there is a malfunction in the throttle actuator. In addition, if the throttle valve does not function properly (for example, stuck on), the ECM determines that there is a malfunction. The ECM then illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Throttle actuator (throttle body with motor assembly)
Required Sensors/Components (Related) -
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A199313E95
3.656,1.438 3.229,0.385 3.229,0.385 3.521,0.385 false 4.823,1.938 5.25,1.073 5.25,1.073 5.406,1.073 false 2.656,1.938 2.448,1.146 2.448,1.146 2.615,1.146 false 1.25,1.844 1.625,2.01 0.375,0.167 10 false Idling 0.344,2.167 1.906,2.479 1.563,0.313 10 false Power Switch on (IG) 2.125,1.99 2.313,2.177 0.188,0.188 10 false [A] 3.854,1.74 4.042,1.927 0.188,0.188 10 false [B] 5.49,0.99 6.125,1.135 0.635,0.146 10 false Released 3.594,0.292 4.323,0.438 0.729,0.146 10 false Depressed 3.49,2.719 4.688,2.906 1.198,0.188 10 false 2 seconds or more 5.26,3.292 5.5,3.5 0.24,0.208 10 false [C] 3.625,3.021 5.24,3.208 1.615,0.188 10 false 16 seconds or more 2.667,1.073 3.302,1.219 0.635,0.146 10 false Released

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on [A].

6.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

7.

Start the engine.

8.

With the vehicle stationary, fully depress the accelerator pedal and quickly release it [B].

9.

Check that 16 seconds or more have elapsed from the instant when the accelerator pedal is first depressed.

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P2102 or P2103.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.




FAIL-SAFE

When either of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 5.5° throttle angle by the return spring. The ECM stops the engine and the vehicle can be driver using solely the hybrid system. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the power switch is then turned off.

WIRING DIAGRAM

A275611E01
0.984,3.813 2.027,3.997 1.042,0.184 10 Auxiliary Battery 1.268,2.566 1.567,2.723 0.299,0.157 10 C12 1.268,2.73 3.601,3.076 2.333,0.346 10 Throttle Actuator (Built into Throttle Body with Motor Assembly) 1.515,0.842 1.909,0.999 0.394,0.157 10 ETCS 2.663,1.264 2.884,1.420 0.221,0.157 10 M+ 2.663,2.111 2.884,2.268 0.221,0.157 10 M- 2.949,1.264 3.061,1.420 0.112,0.157 10 2 2.949,2.111 3.052,2.268 0.103,0.157 10 1 2.027,4.322 3.018,4.479 0.992,0.157 10 *: Shielded 4.52,2.737 4.692,2.894 0.172,0.157 10 58 4.52,2.107 4.692,2.263 0.172,0.157 10 30 4.52,1.264 4.692,1.420 0.172,0.157 10 60 4.52,0.607 4.718,0.764 0.198,0.157 10 29 5.292,4.553 5.568,4.709 0.276,0.157 10 C10 4.779,0.605 5.097,0.762 0.318,0.157 10 +BM 4.779,1.264 5.000,1.420 0.221,0.157 10 M+ 4.779,2.104 5.000,2.261 0.221,0.157 10 M- 4.779,2.826 5.155,2.983 0.375,0.157 10 GE01 4.779,3.294 5.212,3.451 0.433,0.157 10 ME01 4.779,3.891 5.212,4.047 0.433,0.157 10 E1 4.52,3.297 4.692,3.454 0.172,0.157 10 59 4.52,3.788 4.704,3.944 0.184,0.157 10 16 5.606,4.553 5.938,4.709 0.332,0.157 10 ECM 5.304,1.469 6.376,1.797 1.073,0.327 10 Throttle Actuator Control Circuit 0.834,2.269 1.205,2.426 0.372,0.157 10 MAIN 3.615,2.548 3.787,2.705 0.172,0.157 10 *

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Duty (Open) / Throttle Motor Duty (Close)) can be read using the GTS. However, the ECM shuts off the throttle actuator current when the electronic throttle control system malfunctions.



PROCEDURE

1.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
a.

Inspect the throttle body with motor assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>THROTTLE BODY>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C12-2 (M+) - C10-60 (M+) Always Below 1 Ω
C12-1 (M-) - C10-30 (M-) Always Below 1 Ω
C12-2 (M+) or C10-60 (M+) - Body ground Always 10 kΩ or higher
C12-1 (M-) or C10-30 (M-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for foreign objects between the throttle valve and the housing.

OK:

No foreign objects between the throttle valve and housing.


HINT:

Perform "Inspection After Repair" after cleaning the throttle body with motor assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE VALVE)

NG

REMOVE FOREIGN OBJECT AND CLEAN THROTTLE BODY WITH MOTOR ASSEMBLY

4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE VALVE)
a.

Check if the throttle valve opens and closes smoothly.

OK:

Throttle valve opens and closes smoothly.


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY