Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  


DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A209140E90
2.563,4.583 2.844,4.281 2.844,4.281 3.615,4.281 false 3.177,4.802 3.323,5.031 3.323,5.031 3.854,5.031 false 4.938,0.833 6.604,1.042 1.667,0.208 10 false Cam Position Sensor 4.917,1.354 6.698,1.594 1.781,0.24 10 false Crank Position Sensor 0.094,0.042 0.969,0.24 0.875,0.198 10 false VVT System: 2.333,1.958 3.615,2.135 1.281,0.177 10 false Target Valve Timing 2.333,1.292 3.615,1.469 1.281,0.177 10 false Actual Valve Timing 2.688,2.698 3.406,2.875 0.719,0.177 10 false Correction 2.823,3.208 3.229,3.385 0.406,0.177 10 false ECM 1.604,3.75 4.49,3.938 2.885,0.188 10 false Camshaft Timing Oil Control Valve Assembly 0.167,2.688 0.865,2.865 0.698,0.177 10 false Duty-cycle 4.531,1.854 6.76,2.073 2.229,0.219 10 false Mass Air Flow Meter Sub-assembly 4.458,2.875 6.76,3.073 2.302,0.198 10 false Engine Coolant Temperature Sensor 4.844,2.375 6.375,2.542 1.531,0.167 10 false Throttle Position Sensor 4.885,3.385 6.323,3.563 1.438,0.177 10 false Vehicle Speed Signal 0.313,4.271 1.677,4.479 1.365,0.208 10 false Engine Oil Pressure 3.656,4.198 6.958,4.458 3.302,0.26 10 false VVT Controller (Camshaft Timing Gear Assembly) 3.885,4.948 4.99,5.135 1.104,0.188 10 false Intake Camshaft

DTC No. DTC Detection Condition Trouble Area
P0010 Open or short in camshaft timing oil control valve assembly circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly circuit

·

Camshaft timing oil control valve assembly

·

ECM



MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the camshaft timing oil control valve assembly circuit. If the camshaft timing oil control valve duty-cycle is excessively high or low while the power switch is on (IG) or the engine is running, the ECM will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Wait 5 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0010.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A255118E18
0.557,1.862 2.341,2.232 1.785,0.370 10 Camshaft Timing Oil Control Valve Assembly 0.24,1.862 0.535,2.008 0.295,0.145 10 C20 1.591,0.804 1.698,0.950 0.107,0.145 10 1 1.591,1.44 1.698,1.585 0.107,0.145 10 2 4.864,0.8 5.072,0.945 0.207,0.145 10 75 4.863,1.442 5.065,1.587 0.202,0.145 10 74 5.136,1.444 5.543,1.589 0.407,0.145 10 OC1- 5.136,0.808 5.543,0.953 0.407,0.145 10 OC1+ 5.595,2.224 5.925,2.370 0.331,0.145 10 ECM 5.27,2.224 5.564,2.370 0.295,0.145 10 C10

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P0010)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTC after recording the freeze frame data and DTC.


e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


i.

Start the engine and allow the engine to idle.


j.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


k.

Read the DTCs.

Result
Result Proceed to
DTC P0010 is output A
DTCs are not output B



A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C20-1 - C10-75 (OC1+) Always Below 1 Ω
C20-2 - C10-74 (OC1-) Always Below 1 Ω
C20-1 or C10-75 (OC1+) - Body ground Always 10 kΩ or higher
C20-2 or C10-74 (OC1-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR