Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P011B  Engine Coolant Temperature / Intake Air Temperature Correlation  


DESCRIPTION

The engine has two temperature sensors, an engine coolant temperature sensor and an intake air temperature sensor, to detect temperature while the engine is operating. A thermistor, whose resistance value varies according to the temperature, is built into each sensor. When the temperature becomes low, the resistance of the thermistor increases. When the temperature becomes high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes. Based on these temperature signals output from the sensors, the ECM determines the fuel injection duration and the ignition timing to control the engine.

DTC No. DTC Detection Condition Trouble Area
P011B

All of the following conditions are met (2 trip detection logic):

(a)

The auxiliary battery voltage is 10.5 V or higher.

(b)

7 hours or more have elapsed since the engine stopped on the previous trip.

(c)

82 seconds or more after a cold engine start.

(d)

Either of the following conditions is met:

(1)

The minimum intake air temperature after the engine starts is -10°C (14°F) or higher.

(2)

The engine coolant temperature before the engine starts is -10°C (14°F) or higher.


(e)

The difference between the readings of the engine coolant temperature and intake air temperature is higher than 25°C (25°F).



·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

Engine coolant temperature sensor

·

ECM



A379316E03
0.26,0.156 3.25,0.688 2.99,0.531 10 false Difference Between Engine Coolant Temperature and Intake Air Temperature 0.771,1.156 1.417,1.49 0.646,0.333 10 false °C 0.635,1.604 1.448,2.229 0.813,0.625 10 false 40 0.615,2.375 5.771,2.844 5.156,0.469 10 false 25 0.438,3.177 1.083,3.51 0.646,0.333 10 false 0 0.583,3.813 6.188,4.49 5.604,0.677 10 false -25 0.427,5.208 1.833,5.625 1.406,0.417 10 false Power Switch off 1.896,4.906 2.542,5.24 0.646,0.333 10 false 5 2.396,4.906 3.042,5.24 0.646,0.333 10 false 7 2.958,5.188 4,5.531 1.042,0.344 10 false Engine Start 5.979,4.906 6.625,5.24 0.646,0.333 10 false Time (h) 4.156,4.323 4.802,4.656 0.646,0.333 10 false Fail 5.031,2.375 5.99,2.729 0.958,0.354 10 false 25°C 5,3.792 6.281,4.125 1.281,0.333 10 false -25°C 3.677,1.604 4.938,2 1.26,0.396 10 false 82 Seconds 4.354,1.917 5,2.25 0.646,0.333 10 false Fail

HINT:
·

Waiting is required to prevent the temperature of the engine from affecting the readings. If the engine has been operated recently, it is not possible to accurately compare the readings.


·

For diagnosis, in order to duplicate the detection conditions of the DTC, it is necessary to park the vehicle for 7 hours. Parking the vehicle for 7 hours ensures that the actual temperature of the engine coolant temperature and intake air temperature are very similar. When the vehicle has been parked for less than 7 hours, differences in the readings may exist, but this does not necessarily indicate a fault.



MONITOR DESCRIPTION

The ECM monitors the difference between the engine coolant temperature and the intake air temperature when the engine is started cold to accurately detect the engine temperature conditions. The monitor runs when the engine is started after 7 hours or more have elapsed since the engine was stopped (power switch turned off) on the previous trip. If the difference between the engine coolant temperature and the intake air temperature on a cold start exceeds 25°C (45°F), the ECM interprets this as a malfunction in the engine coolant temperature sensor circuit and intake air temperature sensor circuit, and stores the DTC.

MONITOR STRATEGY

Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

A213993E56
1.083,1.271 1.635,1.604 0.552,0.333 10 false Idling 0.281,2.302 1.625,2.583 1.344,0.281 10 false Power Switch off 2.094,1.656 2.573,2.083 0.479,0.427 10 false [A] 3.375,2.156 3.948,2.583 0.573,0.427 10 false [B] 5.229,1.125 5.698,1.49 0.469,0.365 10 false [C] 6.167,2.906 6.552,3.271 0.385,0.365 10 false [D] 4.719,2.625 6.167,2.969 1.448,0.344 10 false 2 minutes or more 2.948,2.563 4.198,2.958 1.25,0.396 10 false 7.5 hours or more 0.125,1.813 1.49,2.344 1.365,0.531 10 false Power Switch on (IG)

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) [A].

4.

Turn the power switch off.

5.

With the engine stopped, leave the vehicle as is for 7.5 hours or more [B].

6.

Turn the power switch on (IG) and turn the GTS on.

7.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

8.

Start the engine and wait 2 minutes or more [C].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P011B.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [D] again.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P011B)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P011B is output A
DTC P011B and other DTCs are output B

HINT:

If any DTCs other than P011B are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (INTAKE AIR)

B

2.READ VALUE USING GTS (INTAKE AIR)
a.

Leave the vehicle for 7 hours or more.

HINT:

It is necessary to leave the vehicle for 7 hours or more to create conditions similar to the DTC detection conditions.



b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.


f.

Read the value displayed on the GTS.

Standard:

Difference between the intake air temperature and the actual outside air temperature is within 10°C (18°F).


HINT:
·

Temperature readings on the outside temperature gauge of the vehicle (if equipped) are not suitable for comparing to the intake air temperature reading. The outside temperature gauge has a significant delay built in to prevent swings in the temperature display. Use an accurate thermometer to determine the outside air temperature.

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION





OK

3.READ VALUE USING GTS (COOLANT TEMP)

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

3.READ VALUE USING GTS (COOLANT TEMP)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.


e.

Read the value displayed on the GTS.

Standard:

The difference between the coolant temperature and the actual outside air temperature is within 10°C (18°F).


HINT:
·

If the result is not as specified, check that there are no heat sources such as a block heater in the engine compartment.

·

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION





OK

NG