Home › Engine / Hybrid System › 1NZ-FXE FUEL › FUEL TANK(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057006 1NZ-FXE FUEL _0320555 FUEL TANK(w/ Canister Pump Module) A

1NZ-FXE FUEL  FUEL TANK(w/ Canister Pump Module)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

a.
A267908C01
1.948,0.708 1.427,0.188 1.427,0.188 1.323,0.188 false 1.156,0.094 1.375,0.281 0.219,0.188 10 false *a
*a Rope


When removing and installing the fuel tank assembly, arrange the inlet hose as shown in the illustration, and secure the fuel tank assembly using rope or similar.

NOTICE:

Depending on the arrangement of the inlet hose during removal, the inlet hose and rear suspension may interfere and cause fuel leaks.



Hide 77020A 2.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 3.DRAIN FUEL

Hide 77310A 4.REMOVE FUEL TANK CAP ASSEMBLY

Hide 58156 5.REMOVE FRONT NO. 4 FLOOR HEAT INSULATOR

a.
A267873

Remove the 2 nuts and front No. 4 floor heat insulator.


Hide 77606 6.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A267874

Pinch and remove the clip.


b.

Remove the bolt and No. 1 fuel tank protector sub-assembly.


Hide 77266A 7.REMOVE NO. 1 FUEL TUBE PROTECTOR

a.
A275852C01
1.749,0.3 1.919,0.484 0.170,0.184 10 *1 1.441,0.581 1.634,0.389 1.634,0.389 1.73,0.389 false
*1 No. 1 Fuel Tube Protector


Remove the No. 1 fuel tube protector from the fuel tube connector.


Hide 77209F 8.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Pull the tabs of the retainer to disengage the lock claws and pull out the fuel tank main tube sub-assembly.

A408570C01
3.719,1.479 3.813,1.646 3.813,1.646 3.927,1.646 false 4.708,1.365 5.01,1.365 false 5.354,2.198 5.656,2.198 5.656,2.198 5.656,1.885 false 5.531,2.198 5.531,1.896 false 5.917,2.302 5.917,2.042 false 5.969,1.563 5.969,1.188 5.969,1.188 6.156,1.188 true 1.115,1.917 1.229,1.917 1.229,1.917 1.396,1.708 true 0.844,0.365 1,0.365 1,0.365 1.26,0.906 true 6.031,1.854 6.271,2.188 6.271,2.188 6.406,2.188 false 0.688,0.292 1,0.448 0.313,0.156 10 false *1 0.938,1.844 1.25,2 0.313,0.156 10 false *2 3.979,1.573 4.292,1.729 0.313,0.156 10 false *a 5.188,2.125 5.5,2.281 0.313,0.156 10 false *c 5.833,2.333 6.146,2.49 0.313,0.156 10 false *d 4.542,1.281 4.854,1.438 0.313,0.156 10 false *b 6.198,1.104 6.51,1.26 0.313,0.156 10 false *a 6.458,2.104 6.771,2.26 0.313,0.156 10 false *e
*1 Fuel Tank Main Tube Sub-assembly *2 Fuel Tank Pipe Setting Holder
*a Retainer *b Nylon Tube
*c O-ring *d Fuel Tube Connector
*e Fuel Pipe - -


NOTICE:
·

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Be sure to disconnect the fuel tube connector by hand.

·

Do not bend, twist, pinch or kink the nylon tube.

·

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.

·

If the fuel tube connector and fuel pipe are stuck, push and pull to release them.




b.

Disengage the clamp and separate the fuel tank pipe setting holder.


Hide 10.REMOVE REAR WHEEL (for LH Side)

Hide 77100 11.REMOVE FUEL TANK ASSEMBLY

a.
A267910

Remove the bolt, disengage the clamp and separate the fuel tank filler pipe assembly.


b.
A267879

Support the fuel tank assembly using an engine lifter.

HINT:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



c.
A261048

Remove the 4 bolts and fuel tank assembly.

NOTICE:
·

Slowly operate the engine lifter to lower the fuel tank assembly.

·

Be careful not to drop the fuel tank assembly.




Hide 77209F 12.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A267911C01
1.049,1.421 1.215,1.571 0.165,0.150 10 *1 0.763,1.688 0.928,1.838 0.165,0.150 10 *2 1.522,1.649 1.38,1.507 1.38,1.507 1.231,1.507 false 1.295,1.938 1.139,1.783 1.139,1.783 0.961,1.783 false
*1 Fuel Tank Pipe Setting Holder
*2 Fuel Tank Main Tube Sub-assembly


Disengage the clamp and remove the fuel tank pipe setting holder.


b.

Disengage the 2 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly.


Hide 77404 13.REMOVE FUEL TANK VENT HOSE SUB-ASSEMBLY

a.
A267912

Disengage the clamp to remove the fuel tank vent hose sub-assembly from the fuel tank assembly.


Hide 77277R 14.REMOVE FUEL TANK FILLER PIPE PROTECTOR

a.
A259865C01
0.854,0.406 1.125,0.135 1.125,0.135 1.313,0.135 false 2.25,3.177 2.542,3.469 2.542,3.469 2.646,3.469 false 1.344,0.063 1.5,0.24 0.156,0.177 10 false *1 2.667,3.385 2.823,3.563 0.156,0.177 10 false *2
*1 No. 1 Fuel Tube Support Protector
*2 Fuel Tank Filler Pipe Protector


Remove the clip.


b.

Disengage the 2 claws to remove the No. 1 fuel tube support protector.


c.

Disengage the 2 claws to remove the fuel tank filler pipe protector.


Hide 77229E 15.REMOVE BREATHER TUBE CLAMP

a.
A267913

Disengage the claw and clamp as shown in the illustration, and remove the breather tube clamp.