Home › Engine / Hybrid System › 1NZ-FXE FUEL › FUEL TANK(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057006 1NZ-FXE FUEL _0320555 FUEL TANK(w/ Canister Pump Module) A

1NZ-FXE FUEL  FUEL TANK(w/ Canister Pump Module)  INSTALLATION  


PROCEDURE

Hide 77229E 1.INSTALL BREATHER TUBE CLAMP

a.

Engage the claw and clamp and install the breather tube clamp.


Hide 77277R 2.INSTALL FUEL TANK FILLER PIPE PROTECTOR

a.

Engage the 2 claws to install the fuel tank filler pipe protector.


b.

Engage the 2 claws to install the No. 1 fuel tube support protector.


c.

Install the clip.


Hide 77404 3.INSTALL FUEL TANK VENT HOSE SUB-ASSEMBLY

a.

Engage the clamp to install the fuel tank vent hose sub-assembly to the fuel tank assembly.


Hide 77209F 4.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Engage the 2 clamps to install the fuel tank main tube sub-assembly to the fuel tank assembly.


b.

Engage the clamp to install the fuel tank pipe setting holder.


Hide 77100 5.INSTALL FUEL TANK ASSEMBLY

a.

Clean the bolt holes.


b.

Using an engine lifter, set the fuel tank assembly in the installation position.

NOTICE:

Be careful not to drop the fuel tank assembly.



c.

Install the fuel tank assembly with 4 new bolts.

Torque:
14 N*m (146 kgf*cm, 11 ft.*lbf)


d.

Engage the claw and install the fuel tank filler pipe assembly.


e.

Install the bolt.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


Hide 77209F 7.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Align the fuel tube connector with the fuel pipe, connect the fuel tube connector and push the retainer in until the retainer makes a "click" sound to lock the claws of the retainer.

A408571C01
3.719,1.49 3.75,1.646 3.75,1.646 3.854,1.646 false 4.708,1.344 5.01,1.344 false 5.969,1.563 5.969,1.271 5.969,1.271 6.135,1.271 true 6.021,1.865 6.333,2.219 6.333,2.219 6.438,2.219 false 5.906,2.302 5.906,2.042 false 5.531,2.198 5.531,1.906 false 5.365,2.198 5.656,2.198 5.656,2.198 5.656,1.896 false 0.917,1.948 1.042,1.948 1.042,1.948 1.344,1.729 true 0.823,0.406 0.948,0.406 0.948,0.406 1.26,0.917 true 0.646,0.323 0.958,0.479 0.313,0.156 10 false *1 0.729,1.865 1.042,2.021 0.313,0.156 10 false *2 3.906,1.563 4.219,1.719 0.313,0.156 10 false *a 4.552,1.26 4.865,1.417 0.313,0.156 10 false *b 5.198,2.104 5.51,2.26 0.313,0.156 10 false *c 5.813,2.313 6.125,2.469 0.313,0.156 10 false *d 6.5,2.135 6.813,2.292 0.313,0.156 10 false *e 6.188,1.188 6.5,1.344 0.313,0.156 10 false *a
*1 Fuel Tank Main Tube Sub-assembly *2 Fuel Tank Pipe Setting Holder
*a Retainer *b Nylon Tube
*c O-ring *d Fuel Tube Connector
*e Fuel Pipe - -


NOTICE:
·

Check that there is no damage or foreign matter around the connecting parts of the fuel tube connector and fuel pipe before starting this step.

·

After connecting the fuel tube connector, check that the fuel tube connector is securely connected by pulling on the fuel tube connector.




b.

Engage the clamp to install the fuel tank pipe setting holder.


Hide 77266A 8.INSTALL NO. 1 FUEL TUBE PROTECTOR

a.

Install the No. 1 fuel tube protector to the fuel tube connector.


Hide 77606 9.INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.

Install the No. 1 fuel tank protector sub-assembly with the bolt and clip.

Torque:
Bolt : 5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 58156 10.INSTALL FRONT NO. 4 FLOOR HEAT INSULATOR

a.
U159068C01
1.125,0.938 1.25,1.104 0.125,0.167 10 false A 2.396,0.781 2.552,0.958 0.156,0.177 10 true B
V100136

Front


Install the front No. 4 floor heat insulator with the 2 nuts.

Torque:
Nut (A) : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
Nut (B) : 5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 77310A 11.INSTALL FUEL TANK CAP ASSEMBLY

Hide 77020A 12.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 13.ADD FUEL

Hide 14.INSTALL REAR WHEEL (for LH Side)

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)