Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057034 DOOR LOCK _0278072 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch or Door Key Cylinder  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives switch signals from the door control switch (power window regulator master switch assembly) and driver door key cylinder lock or unlock switch signals from the front door lock assembly LH*1 or front door lock assembly RH*2. The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.

·

*1: for LHD

·

*2: for RHD


WIRING DIAGRAM

for LHD


B296423E14
5.479,4.979 7.125,5.302 1.646,0.323 10 false Main Body ECU (Multiplex Network Body ECU) 0.792,2.104 3.313,2.51 2.521,0.406 10 false Door Key Lock and Unlock Switch (Front Door Lock Assembly LH) 0.729,4.385 2.979,4.802 2.25,0.417 10 false Door Control Switch (Power Window Regulator Master Switch Assembly) 0.802,1.896 1.052,2.104 0.25,0.208 10 false J6 2.208,1.625 2.542,1.875 0.333,0.25 10 false 10 2.229,1.063 2.51,1.24 0.281,0.177 10 false 9 1.229,3.563 1.51,3.792 0.281,0.229 10 false 1 2.219,3.302 2.552,3.51 0.333,0.208 10 false 9*1 2.229,3.854 2.438,4.052 0.208,0.198 10 false 2 5.75,1.063 5.969,1.271 0.219,0.208 10 false 11 5.625,1.604 6.177,1.823 0.552,0.219 10 false 24*2 5.823,3.844 6,4.021 0.177,0.177 10 false 9 5.771,3.292 6.021,3.521 0.25,0.229 10 false 10 1.948,3.281 2.156,3.427 0.208,0.146 10 false UL 2.031,3.854 2.198,4.042 0.167,0.188 10 false L 1.427,3.573 1.542,3.719 0.115,0.146 10 false E 1.938,1.625 2.219,1.802 0.281,0.177 10 false UL 2.042,1.063 2.229,1.281 0.188,0.219 10 false L 1.427,1.354 1.542,1.5 0.115,0.146 10 false E 6.042,1.167 6.292,1.375 0.25,0.208 10 false L2 6.031,1.635 6.646,1.917 0.615,0.281 10 false UL2*1 6.042,3.979 6.26,4.188 0.219,0.208 10 false L1 6.042,3.417 6.375,3.615 0.333,0.198 10 false UL1 5.469,4.802 5.802,5 0.333,0.198 10 false G59 0.719,4.177 1.021,4.396 0.302,0.219 10 false J1 3.177,5.052 5.135,5.313 1.958,0.26 10 false *2: w/ Canister Pump Module 3.177,4.708 5.333,4.917 2.156,0.208 10 false *1: w/o Canister Pump Module 2.219,3.156 2.521,3.365 0.302,0.208 10 false 8*2 1.25,1.354 1.5,1.563 0.25,0.208 10 false 7 6.031,1.802 6.646,2.083 0.615,0.281 10 false UL3*2 5.615,1.438 6.167,1.656 0.552,0.219 10 false 12*1


for RHD


B296423E13
5.469,5.01 7.125,5.375 1.656,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 0.698,2.104 3.208,2.542 2.51,0.438 10 false Door Key Lock and Unlock Switch (Front Door Lock Assembly RH) 0.635,4.552 2.917,4.938 2.281,0.385 10 false Door Control Switch (Power Window Regulator Master Switch Assembly) 1.25,1.333 1.51,1.573 0.26,0.24 10 false 8 2.229,1.625 2.656,1.813 0.427,0.188 10 false 5 2.229,1.063 2.552,1.344 0.323,0.281 10 false 6 1.229,3.583 1.469,3.771 0.24,0.188 10 false 9 2.219,3.844 2.344,4.031 0.125,0.188 10 false 2 5.75,1.031 5.948,1.208 0.198,0.177 10 false 11 5.75,1.615 5.969,1.792 0.219,0.177 10 false 12 5.802,3.854 5.927,4.021 0.125,0.167 10 false 9 5.75,3.292 6.021,3.563 0.271,0.271 10 false 10 1.948,3.302 2.156,3.448 0.208,0.146 10 false UL 2.01,3.844 2.167,4.031 0.156,0.188 10 false L 1.417,3.604 1.531,3.75 0.115,0.146 10 false E 1.948,1.625 2.167,1.771 0.219,0.146 10 false UL 2.031,1.052 2.146,1.198 0.115,0.146 10 false L 1.417,1.354 1.531,1.5 0.115,0.146 10 false E 6.042,1.177 6.271,1.385 0.229,0.208 10 false L2 6.042,1.74 6.365,1.927 0.323,0.188 10 false UL2 6.042,3.969 6.344,4.188 0.302,0.219 10 false L1 6.042,3.406 6.396,3.615 0.354,0.208 10 false UL1 5.469,4.823 5.844,5 0.375,0.177 10 false G59 0.635,4.375 0.979,4.573 0.344,0.198 10 false H1 2.219,3.302 2.49,3.49 0.271,0.188 10 false 8 0.688,1.948 0.99,2.198 0.302,0.25 10 false H6


PROCEDURE

1.CHECK DOOR LOCK OPERATION
a.

Check door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

Result:
Result Proceed to
All doors cannot be locked through door control switch (power window regulator master switch assembly) A
All doors cannot be locked through driver door key cylinder B




A

2.READ VALUE USING GTS (DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY))

B

5.READ VALUE USING GTS (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH)
2.READ VALUE USING GTS (DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY))
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Lock SW-Lock Door control switch (power window regulator master switch assembly) lock signal OFF or ON OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed
ON: Lock side of door control switch (power window regulator master switch assembly) pushed
-
Door Lock SW-Unlock Door control switch (power window regulator master switch assembly) unlock signal OFF or ON OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed
ON: Unlock side of door control switch (power window regulator master switch assembly) pushed
-

OK:

The GTS indicates ON or OFF according to the switch operation shown in the table above.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.INSPECT DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
3.INSPECT DOOR CONTROL SWITCH (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
a.

for LHD

i.
B302422C45
1.094,1.698 1.094,0.906 1.094,0.906 0.792,0.906 false 2.333,1.698 2.333,0.979 2.333,0.979 2.604,0.979 false 2.177,1.698 2.177,0.479 2.177,0.479 2.604,0.479 false 1.24,1.677 1.24,0.615 1.24,0.615 0.938,0.615 false 0.208,0.219 0.396,0.385 0.188,0.167 10 false *a 2.646,0.906 2.854,1.135 0.208,0.229 10 false E 2.646,0.396 2.844,0.594 0.198,0.198 10 false L 0.427,0.833 0.958,1.031 0.531,0.198 10 false UL*A 0.573,0.542 1.104,0.74 0.531,0.198 10 false UL*B
*A w/o Canister Pump Module
*B w/ Canister Pump Module
*a Component without harness connected
(Door Control Switch (Power Window Regulator Master Switch Assembly))


Remove the door control switch (power window regulator master switch assembly).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (L) - 1 (E) Lock switch pushed Below 1 Ω
2 (L) - 1 (E) Lock switch not pushed 10 kΩ or higher
9 (UL) - 1 (E)*1
8 (UL) - 1 (E)*2
Unlock switch pushed Below 1 Ω
9 (UL) - 1 (E)*1
8 (UL) - 1 (E)*2
Unlock switch pushed 10 kΩ or higher


*1: w/o Canister Pump Module

*2: w/ Canister Pump Module




b.

for RHD

i.
B302422C46
1.253,1.682 1.253,0.543 1.253,0.543 0.948,0.543 false 1.11,1.684 1.11,0.967 1.11,0.967 0.841,0.967 false 2.188,1.69 2.188,0.71 2.188,0.71 2.615,0.71 false 0.206,0.217 0.398,0.388 0.192,0.171 10 *a 0.681,0.892 0.791,1.035 0.111,0.143 10 E 2.653,0.634 2.748,0.774 0.095,0.140 10 L 0.671,0.465 0.880,0.604 0.209,0.140 10 UL
*a Component without harness connected
(Door Control Switch (Power Window Regulator Master Switch Assembly))


Remove the door control switch (power window regulator master switch assembly).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (L) - 9 (E) Lock switch pushed Below 1 Ω
2 (L) - 9 (E) Lock switch not pushed 10 kΩ or higher
8 (UL) - 9 (E) Unlock switch pushed Below 1 Ω
8 (UL) - 9 (E) Unlock switch pushed 10 kΩ or higher





OK

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

for LHD

i.

Disconnect the G59 main body ECU (multiplex network body ECU) connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-2 (L) - G59-9 (L1) Always Below 1 Ω
J1-9 (UL) - G59-10 (UL1)*1
J1-8 (UL) - G59-10 (UL1)*2
Always Below 1 Ω
J1-1 (E) - Body ground Always Below 1 Ω
J1-2 (L) - Body ground Always 10 kΩ or higher
J1-9 (UL) - Body ground*1
J1-8 (UL) - Body ground*2
Always 10 kΩ or higher


*1: w/o Canister Pump Module

*2: w/ Canister Pump Module




b.

for RHD

i.

Disconnect the G59 main body ECU (multiplex network body ECU) connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H1-2 (L) - G59-9 (L1) Always Below 1 Ω
H1-8 (UL) - G59-10 (UL1) Always Below 1 Ω
H1-9 (E) - Body ground Always Below 1 Ω
H1-2 (L) - Body ground Always 10 kΩ or higher
H1-8 (UL) - Body ground Always 10 kΩ or higher





OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Key SW-Lock Driver door key-linked lock/unlock switch lock signal OFF or ON OFF: Driver door key cylinder not turned to lock position
ON: Driver door key cylinder turned to lock position
-
D Door Key SW-UL Driver door key-linked lock/unlock switch unlock signal OFF or ON OFF: Driver door key cylinder not turned to unlock position
ON: Driver door key cylinder turned to unlock position
-

OK:

The GTS indicates ON or OFF according to the key cylinder operation shown in the table.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

6.INSPECT FRONT DOOR LOCK ASSEMBLY
6.INSPECT FRONT DOOR LOCK ASSEMBLY
a.

for LHD

i.

Remove the front door lock assembly LH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


ii.
B280166C02
0.101,0.076 0.266,0.241 0.165,0.165 10 *a 2.851,1.623 3.016,1.788 0.165,0.165 10 *b 3.057,0.558 3.223,0.723 0.165,0.165 10 *c 2.273,3.437 2.273,3.802 2.273,3.802 2.086,3.802 false 2.427,3.437 2.427,4.115 2.427,4.115 1.931,4.115 false 2.737,3.437 2.737,4.436 2.737,4.436 2.086,4.436 false 1.927,4.36 2.044,4.502 0.117,0.142 10 E 1.79,4.034 1.906,4.176 0.117,0.142 10 L 1.833,3.716 2.033,3.858 0.200,0.142 10 UL
*a Component without harness connected
(Front Door Lock Assembly LH)
*b Unlock
*c Lock


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (L) - 7 (E) Turned to lock Below 1 Ω
9 (L) - 7 (E) Not turned 10 kΩ or higher
10 (UL) - 7 (E) Turned to unlock Below 1 Ω
10 (UL) - 7 (E) Not turned 10 kΩ or higher




b.

for RHD

i.

Remove the front door lock assembly RH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


ii.
B280267C04
0.104,0.072 0.259,0.221 0.155,0.149 10 *a 0.291,0.782 0.446,0.931 0.155,0.149 10 *c 0.634,1.915 0.789,2.065 0.155,0.149 10 *b 0.772,3.514 0.772,4.445 0.772,4.445 1.367,4.445 false 1.047,3.514 1.047,4.13 1.047,4.13 1.367,4.13 false 1.185,3.514 1.185,3.809 1.185,3.809 1.367,3.809 false 1.387,4.353 1.503,4.495 0.117,0.142 10 E 1.387,4.044 1.496,4.186 0.110,0.142 10 L 1.387,3.729 1.596,3.871 0.209,0.142 10 UL
*a Component without harness connected
(Front Door Lock Assembly RH)
*b Unlock
*c Lock


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Turned to lock Below 1 Ω
6 (L) - 8 (E) Not turned 10 kΩ or higher
5 (UL) - 8 (E) Turned to unlock Below 1 Ω
5 (UL) - 8 (E) Not turned 10 kΩ or higher





OK

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE FRONT DOOR LOCK ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

for LHD

i.

Disconnect the G59 main body ECU (multiplex network body ECU) connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J6-9 (L) - G59-11 (L2) Always Below 1 Ω
J6-10 (UL) - G59-12 (UL2)*1
J6-10 (UL) - G59-24 (UL3)*2
Always Below 1 Ω
J6-7 (E) - Body ground Always Below 1 Ω
G59-11 (L2) - Body ground Always 10 kΩ or higher
G59-12 (UL2) - Body ground*1
G59-24 (UL3) - Body ground*2
Always 10 kΩ or higher


*1: w/o Canister Pump Module

*2: w/ Canister Pump Module




b.

for RHD

i.

Disconnect the G59 main body ECU (multiplex network body ECU) connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-6 (L) - G59-11 (L2) Always Below 1 Ω
H6-5 (UL) - G59-12 (UL2) Always Below 1 Ω
H6-8 (E) - Body ground Always Below 1 Ω
G59-11 (L2) - Body ground Always 10 kΩ or higher
G59-12 (UL2) - Body ground Always 10 kΩ or higher





OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR