Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (w/ Removable Headrest) › from 2017.06
RM2170E _58 Vehicle Interior _057040 SEAT _0278111 FRONT SEAT ASSEMBLY(w/ Removable Headrest) A

SEAT  FRONT SEAT ASSEMBLY(w/ Removable Headrest)  REASSEMBLY  


PROCEDURE

Hide 72211 1.INSTALL SEAT TRACK ADJUSTING HANDLE

a.

Engage the 2 springs to install the seat track adjusting handle to the separate type front seat cushion spring assembly.


Hide 72265D 2.INSTALL SEAT TRACK UPPER RAIL COVER (for Front Side)

a.

Operate the seat track adjusting handle and move the front seat adjuster assembly to the foremost position.


b.
B551875C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the seat track upper rail cover as shown in the illustration.

HINT:

Use the same procedure for both sides.



Hide 72129D 3.INSTALL LOWER NO. 4 SEAT TRACK RAIL PROTECTOR

a.
B550352C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides and 2 claws to install the lower No. 4 seat track rail protector to the separate type front seat cushion spring assembly.


Hide 72265D 4.INSTALL SEAT TRACK UPPER RAIL COVER (for Rear Side)

a.

Operate the seat track adjusting handle and move the front seat adjuster assembly to the rearmost position.


b.

for LH Side:

i.
B551876C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the seat track upper rail cover as shown in the illustration.



c.

for RH Side:

HINT:

Use the same procedure as for the front side.



Hide 72129A 5.INSTALL LOWER NO. 2 SEAT TRACK RAIL PROTECTOR

a.
B481891C02
0,0 0,0 false
V113147C26
0,0 0,0 false

Install in this Direction


Engage the guide and 2 claws to install the lower No. 2 seat track rail protector to the separate type front seat cushion spring assembly.


Hide 71640S 6.INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY

a.

Engage the 4 guides to install the separate type front seatback spring assembly to the separate type front seat cushion spring assembly.


b.

Install the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 82191 7.INSTALL FRONT SEAT WIRE RH (w/ Occupant Classification System)

a.

Connect each connector and engage each clamp to install the front seat wire RH.


Hide 71538B 9.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH (for Driver Side)

a.

Engage the 5 claws to install the front seat cushion edge protector LH.


Hide 71537H 10.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH (for Driver Side)

a.

Engage the 5 claws to install the front seat cushion edge protector RH.


Hide 71538A 11.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH (for Front Passenger Side)

a.

Engage the 5 claws to install the front seat cushion edge protector LH.


Hide 71537G 12.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH (for Front Passenger Side)

a.

Engage the 5 claws to install the front seat cushion edge protector RH.


Hide 71874 13.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)

a.
B301372

Engage the clip to install the front seat lower cushion shield LH.


b.

Engage the hook as shown in the illustration.


c.

Install the screw.


Hide 71873 14.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)

a.
B301374

Engage the clip to install the front seat lower cushion shield RH.


b.

Engage the hook as shown in the illustration.


c.

Install the screw.


Hide 71074S 15.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

a.
B281074

Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 6 new hog rings.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.




Hide 17.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

a.

Temporarily install the separate type front seatback cover with pad.


b.

Engage the 4 claws to install the 2 front seat headrest supports.


c.

Install the 3 brackets with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

CAUTION:
·

For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

·

Make sure that the strap is not twisted after installing the nut.

·

Install the bracket securely.




d.
B301370

Turn back the separate type front seatback cover.


e.
B386950

Using hog ring pliers, install 2 new hog rings.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.




f.
B301368

Using hog ring pliers, install 3 new hog rings.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.




g.
B311802

Using hog ring pliers, install 5 new hog rings.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.




Hide 71072S 18.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

a.
B301356

Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings.

NOTICE:
·

Be careful not to damage the separate type front seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.




b.
B301354

Using hog ring pliers, install 2 new hog rings.

NOTICE:
·

Be careful not to damage the separate type front seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.




Hide 73906 19.INSTALL FRONT SEAT AIRBAG SUB-ASSEMBLY (w/ Occupant Classification System)

Hide 20.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

a.

Temporarily install the separate type front seat cushion cover with pad.


b.

Engage each hook.


c.

w/ Occupant Detection Sensor:

i.
B270301

Engage the clamp to install the connector as shown in the illustration.



Hide 73920A 21.CONNECT FRONT SEAT AIRBAG ASSEMBLY

a.

for LH Side:

i.

Engage the claw and 6 clamps to install the front seat airbag assembly wire harness.



b.

for RH Side:

i.

Engage the claw and 3 clamps to install the front seat airbag assembly wire harness.



c.

Engage the fastener to secure the front seat airbag assembly wire harness.


Hide 71874C 22.INSTALL FRONT SEAT LOWER CUSHION SHIELD (for Driver Side)

a.

Engage the 2 claws to install the front seat lower cushion shield.


Hide 71812D 23.INSTALL FRONT SEAT CUSHION SHIELD

a.

Engage the 2 claws, 4 guides and clip to install the front seat cushion shield.


b.

Install the screw.


Hide 72495 24.INSTALL VERTICAL ADJUSTING HANDLE (for Driver Side)

a.

Install the vertical adjusting handle with the screw.


Hide 72526A 25.INSTALL RECLINING ADJUSTER RELEASE HANDLE

a.

Engage the claw to install the reclining adjuster release handle.


Hide 71849 26.INSTALL SEAT ADJUSTER COVER CAP

a.

Install the 2 seat adjuster cover caps.


Hide 73240 28.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)

Hide 73230 29.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

Hide 71862 30.INSTALL FRONT SEAT INNER CUSHION SHIELD (for LHD Driver Side)

a.

Engage the 2 claws and 4 guides to install the front seat inner cushion shield.


Hide 71861 31.INSTALL FRONT SEAT INNER CUSHION SHIELD (for RHD Driver Side)

a.

Engage the 2 claws and 5 guides to install the front seat inner cushion shield.


Hide 71861 32.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side)

a.

Engage the 2 claws and 5 guides to install the front seat inner cushion shield.


Hide 71074S 33.CONNECT SEPARATE TYPE FRONT SEATBACK COVER

a.

Connect the rubber band of the separate type front seatback cover.