Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278100 STEERING PAD A

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 45187 4.REMOVE LOWER NO. 3 STEERING WHEEL COVER

a.
B289068

Disengage the claw and guide to remove the lower No. 3 steering wheel cover.


Hide 45186 5.REMOVE LOWER NO. 2 STEERING WHEEL COVER

a.
B296300

Disengage the claw and guide to remove the lower No. 2 steering wheel cover.


Hide 45130 6.REMOVE HORN BUTTON ASSEMBLY

CAUTION:

When storing the horn button assembly, keep the airbag deployment side facing upward.


a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B296301C01
0.542,0.49 0.771,0.49 true 2.896,0.406 2.667,0.406 true 0.813,0.396 0.99,0.552 0.177,0.156 10 true *a 2.479,0.323 2.656,0.5 0.177,0.177 10 true *a
*a Torsion Spring


Using a "TORX" driver, push in the 2 torsion springs to disengage the 2 pins.

NOTICE:

Do not drop the horn button assembly.


HINT:

Insert the "TORX" driver from the installation holes in the lower No. 3 steering wheel cover and lower No. 2 steering wheel cover.



d.

Pull out the horn button assembly from the steering wheel assembly and support the horn button assembly with one hand.

NOTICE:

When removing the horn button assembly, do not pull the airbag wire harness.



e.
B312017C01
1.781,2.302 2.479,2.302 true 0.74,2.604 1.802,2.604 1.802,2.604 1.802,2.5 false 0.74,2.604 1.802,2.604 1.802,2.604 1.802,2.5 true 1.51,2.24 1.063,2.24 true 2.646,0.313 2.531,0.198 2.531,0.198 2.385,0.198 true 2.49,2.219 2.667,2.406 0.177,0.188 10 true *a 0.563,2.51 0.729,2.708 0.167,0.198 10 true *b 0.865,2.156 1.042,2.354 0.177,0.198 10 true *c 2.198,0.115 2.375,0.292 0.177,0.177 10 false *d
*a Protective Tape
*b Airbag Connector
*c Horn Connector
*d Airbag Connector Lock


w/o Occupant Classification System:

i.

Disconnect the horn connector from the horn button assembly.


ii.

Using a screwdriver with its tip wrapped with protective tape, release the airbag connector lock.


iii.

Disconnect the airbag connector to remove the horn button assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.




f.
B296304C01
1.885,2.281 2.583,2.281 true 1.719,2.635 1.719,2.51 false 0.74,2.635 1.896,2.635 1.896,2.635 1.896,2.469 false 0.74,2.635 1.896,2.635 1.896,2.635 1.896,2.469 true 1.51,2.281 1.063,2.281 true 2.646,0.365 2.531,0.26 2.531,0.26 2.385,0.26 false 1.719,2.635 1.719,2.51 true 2.604,2.198 2.76,2.375 0.156,0.177 10 true *a 0.563,2.542 0.729,2.719 0.167,0.177 10 true *b 0.854,2.188 1.01,2.365 0.156,0.177 10 true *c 2.198,0.167 2.375,0.344 0.177,0.177 10 false *d
*a Protective Tape
*b Airbag Connector
*c Horn Connector
*d Airbag Connector Lock


w/ Occupant Classification System:

i.

Disconnect the horn connector from the horn button assembly.


ii.

Using a screwdriver with its tip wrapped with protective tape, release the 2 airbag connector locks.


iii.

Disconnect the 2 airbag connectors to remove the horn button assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.