Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR(for Front Side) › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0321629 SIDE AIRBAG SENSOR(for Front Side) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR(for Front Side)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89835 1.INSTALL DOOR SIDE AIRBAG SENSOR

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

B296255E05
4.763,1.829 4.955,2.012 0.192,0.183 10 *b 1.4,1.829 1.592,2.012 0.192,0.183 10 *b 4.763,0.568 4.955,0.751 0.192,0.183 10 *a 1.4,0.568 1.592,0.751 0.192,0.183 10 *a

Text in Illustration
*a Incorrect *b Correct


d.

Insert the pin (stopper) into the door hole and install the door side airbag sensor to the front door panel with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the pin (stopper) is securely inserted into the door hole.

·

Tighten the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.




e.

Connect the connector to the door side airbag sensor.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

H103068E01
2.448,1.792 2.448,1.385 false 2.188,0.76 2.302,0.281 2.302,0.281 2.427,0.281 false 2.385,0.99 2.635,0.625 2.635,0.625 2.76,0.625 true 2.479,0.146 2.938,0.344 0.458,0.198 10 false (A) 2.813,0.542 3.271,0.74 0.458,0.198 10 false *1 2.375,1.833 2.833,2.031 0.458,0.198 10 false *2 6.01,3.427 6.469,3.625 0.458,0.198 10 false *a

Text in Illustration
*1 White Housing Lock *2 Yellow CPA
*a Connection is Completed - -

HINT:

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and part (A), as it may result in an insecure fit.




f.

Check that there is no looseness in the installation parts of the door side airbag sensor.


Hide 67602 2.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 3.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

Hide 4.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

Hide 5.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).