Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0321828 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1794  Open in Occupant Classification ECU Battery Positive Line  


DESCRIPTION

DTC B1794 is stored when a malfunction is detected in the occupant detection ECU auxiliary battery positive line.

DTC No. DTC Detections Conditions Trouble Areas
B1794
·

The occupant detection ECU receives an open circuit signal in the occupant detection ECU auxiliary battery positive line.

·

Occupant detection ECU malfunction


·

Auxiliary battery

·

Wire harness

·

Occupant detection ECU



HINT:

When DTC B1650/32 is detected as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1794 is output, perform troubleshooting for the DTC.


WIRING DIAGRAM

C239234E24
5.219,2.771 6.958,3.083 1.74,0.313 10 false Occupant Detection ECU 0.604,0.927 1.49,1.365 0.885,0.438 10 false from Auxiliary Battery 5.302,1.823 5.792,2.188 0.49,0.365 10 false GND 5.302,0.917 5.635,1.167 0.333,0.25 10 false +B 5.135,1.729 5.552,2.073 0.417,0.344 10 false 3 2.958,1.073 3.969,1.448 1.01,0.375 10 false ECU-B NO. 2 5.125,0.813 5.375,1.094 0.25,0.281 10 false 1 5.219,2.615 5.563,2.906 0.344,0.292 10 false O2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK AUXILIARY BATTERY VOLTAGE
a.

Measure the voltage of the auxiliary battery.

Standard Voltage:

11 to 14 V




OK

2.CHECK WIRE HARNESS (SOURCE VOLTAGE)

NG

INSPECT CHARGING SYSTEM AND AUXILIARY BATTERY

2.CHECK WIRE HARNESS (SOURCE VOLTAGE)
a.
C239235C17
0.281,0.969 0.615,1.208 0.333,0.24 1.75,1.052 2,1.76 false 1.313,1.052 1.052,1.771 false 1.875,1.771 2.354,2.021 0.479,0.25 10 false GND 0.958,1.771 1.385,2.063 0.427,0.292 10 false +B 0.365,1.01 0.75,1.344 0.385,0.333 10 false O2 0.083,0.063 0.417,0.365 0.333,0.302 10 false *a
*a Front view of wire harness connector
(to Occupant Detection ECU)


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the connector from the occupant detection ECU.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O2-1 (+B) - Body ground Power switch off 11 to 14 V



g.

Turn the power switch off.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-3 (GND) - Body ground Always Below 1 Ω




OK

3.CHECK DTC

NG

REPLACE WIRE HARNESS

3.CHECK DTC
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Connect the connector to the occupant detection ECU.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in the occupant detection ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).


e.

Clear the DTCs stored in the airbag sensor assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).


f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 10 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1794 is not output.


HINT:

Codes other than DTC B1794 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.



OK

NG

4.REPLACE OCCUPANT DETECTION ECU
4.REPLACE OCCUPANT DETECTION ECU
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.



c.

Connect the cable to the negative (-) auxiliary battery terminal.



NEXT

5.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
5.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
a.

Using the GTS, perform Zero Point Calibration and Sensitivity Check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

END