The occupant classification system detects the front passenger seat condition. It then displays the instrument panel passenger airbag assembly, front seat airbag sub-assembly RH and front seat outer belt assembly RH condition (activated/not activated) using the passenger airbag ON/OFF indicator.
Approximately 6 seconds after the power switch is turned on (IG), the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the conditions listed below.
| Front Passenger Seat Condition | Passenger Airbag ON/OFF Indicator | SRS Warning Light | |
|---|---|---|---|
| ON Indicator | OFF Indicator | ||
| Vacant | OFF | ON | OFF |
| Adult is seated. | ON | OFF | OFF |
| Child is seated. | OFF | ON | OFF |
| Child restraint system is installed. | |||
| Occupant classification system failure | OFF | ON | ON |
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Turn the power switch on (IG), and check the SRS warning light condition.
If a passenger airbag ON/OFF indicator malfunction occurs, the SRS warning light does not illuminate. If the light comes on, a DTC is stored. Troubleshoot for the DTC.
After the primary check period, the SRS warning light turns off.
The primary check is performed for approximately 6 seconds after the power switch is turned on (IG).
OK
NG
(See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
Using the GTS, perform Zero Point Calibration and Sensitivity Check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).
"Zero Point Calibration is complete." and "Sensitivity Check is complete." are displayed.
OK
NG
Loosen the 4 installation bolts of the front seat assembly RH.
Tighten the 4 installation bolts of the front seat assembly RH to the specified torque (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (w/ Removable Headrest)>INSTALLATION).
NEXT
Using the GTS, perform Zero Point Calibration and Sensitivity Check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).
"Zero Point Calibration is complete." and "Sensitivity Check is complete." are displayed.
OK
NG
Using the GTS, read Data List (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST).
Read the display when the passenger side buckle switch is operated.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Passenger Buckle SW | Passenger side buckle switch/
Set: The seat belt is fastened Unset: The seat belt is not fastened NG: Data is not determined |
Set/Unset | - |
The GTS display changes correctly in accordance with the operation of the buckle switch.
OK
NG
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the connectors from the occupant detection ECU and separate type front seat cushion spring assembly (2 occupant classification sensors).
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
OK
NG
Connect the connectors to the separate type front seat cushion spring assembly (2 occupant classification sensors).
Replace the occupant detection ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU(w/ Occupant Classification System)>REMOVAL).
Connect the cable to the negative (-) auxiliary battery terminal.
NEXT
Using the GTS, perform Zero Point Calibration and Sensitivity Check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).
NEXT
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the connectors from the occupant detection ECU and front seat inner belt assembly RH.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
OK
NG
Connect the connector to the occupant detection ECU.
Replace the front seat inner belt assembly RH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).
Connect the cable to the negative (-) auxiliary battery terminal.
NEXT
Using the GTS, perform Zero Point Calibration and Sensitivity Check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).
NEXT