Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0321828 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1780  Front Occupant Classification Sensor LH Circuit Malfunction  


DESCRIPTION

The front occupant classification sensor LH circuit consists of the occupant detection ECU and front occupant classification sensor LH.

DTC B1780 is stored when a malfunction is detected in the front occupant classification sensor LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1780
·

The occupant detection ECU detects a line short, short to ground or B+, or an open in the front occupant classification sensor LH circuit.

·

Front occupant classification sensor LH malfunction

·

Occupant detection ECU malfunction


·

Front seat wire RH

·

Separate type front seat cushion spring assembly (Front occupant classification sensor LH)

·

Occupant detection ECU



WIRING DIAGRAM

C379007E02
5.313,3.073 7.083,3.625 1.771,0.552 10 false Occupant Detection ECU 5.313,2.906 6.781,3.302 1.469,0.396 10 false O1 5.208,0.521 6.677,0.917 1.469,0.396 10 false 1 5.208,1.385 6.677,1.781 1.469,0.396 10 false 3 5.208,2.26 6.677,2.656 1.469,0.396 10 false 5 5.375,0.625 6.844,1.021 1.469,0.396 10 false SVC1 5.375,1.5 6.844,1.896 1.469,0.396 10 false SIG1 5.375,2.354 6.844,2.75 1.469,0.396 10 false SGD1 0.552,2.917 2.021,3.313 1.469,0.396 10 false O4 0.552,3.094 3.76,3.594 3.208,0.5 10 false Separate Type Front Seat Cushion Spring Assembly (Front Occupant Classification Sensor LH) 1.469,0.625 2.938,1.021 1.469,0.396 10 false SVC 1.521,1.5 2.99,1.896 1.469,0.396 10 false SIG 1.469,2.365 2.938,2.76 1.469,0.396 10 false SGD 1.833,0.521 3.302,0.917 1.469,0.396 10 false 1 1.833,1.385 3.302,1.781 1.469,0.396 10 false 2 1.833,2.25 3.302,2.646 1.469,0.396 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

When DTC B1650/32 is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1780 is output, perform troubleshooting for this DTC first.

·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front passenger seat installation bolts to see under the seat cushion.

·

In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.



PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Check that the connectors are properly connected to the occupant detection ECU and separate type front seat cushion spring assembly (front occupant classification sensor LH).

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the occupant detection ECU and separate type front seat cushion spring assembly (front occupant classification sensor LH).


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

2.CHECK FRONT SEAT WIRE RH (SHORT TO B+)

NG

REPLACE FRONT SEAT WIRE RH

2.CHECK FRONT SEAT WIRE RH (SHORT TO B+)
a.
C379008C05
0.958,2.344 1.271,2.573 0.313,0.229 1.542,0.885 1.542,0.302 1.542,0.302 1.375,0.302 false 1.406,2.885 1.76,2.469 false 2.583,2.885 2.198,2.469 false 1.979,2.885 1.979,2.469 false 0.615,0.875 1.146,1.604 0.531,0.729 10 false *1 2.417,0.74 2.885,1.271 0.469,0.531 10 false *2 1.229,0.229 1.688,0.656 0.458,0.427 10 false *3 1.031,2.375 1.594,2.948 0.563,0.573 10 false O1 2.104,0.875 2.573,1.406 0.469,0.531 10 false A 1.813,0.875 2.281,1.406 0.469,0.531 10 false B 1.198,0.875 1.667,1.406 0.469,0.531 10 false C 0.917,0.875 1.385,1.406 0.469,0.531 10 false D 0.708,1.896 1.271,2.469 0.563,0.573 10 false *a 1.219,2.896 1.771,3.198 0.552,0.302 10 false SVC1 1.844,2.896 2.396,3.198 0.552,0.302 10 false SIG1 2.417,2.896 2.969,3.198 0.552,0.302 10 false SGD1
*1 Separate Type Front Seat Cushion Spring Assembly (Front Occupant Classification Sensor LH)
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O1-1 (SVC1) - Body ground Power switch on (IG) Below 1 V
O1-3 (SIG1) - Body ground Power switch on (IG) Below 1 V
O1-5 (SGD1) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.



OK

3.CHECK FRONT SEAT WIRE RH (OPEN)

NG

12.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY
3.CHECK FRONT SEAT WIRE RH (OPEN)
a.
C379009C02
1.188,0.51 1.51,0.74 0.323,0.229 0.719,3.583 1.042,3.813 0.323,0.229 1.594,2.188 1.594,1.688 1.594,1.688 1.427,1.688 false 2.083,3.177 2.417,3.177 false 2.073,4.167 2.406,4.167 false 1.656,1.115 1.969,0.646 false 2.698,1.115 2.406,0.656 false 2.188,1.104 2.188,0.656 false 1.875,3.698 2.302,3.698 false 1.146,4.052 1.542,3.708 false 1.083,3.292 1.688,3.708 false 0.677,2.177 1.073,2.615 0.396,0.438 10 false *1 2.469,2.042 2.948,2.635 0.479,0.594 10 false *2 1.271,1.615 1.615,1.865 0.344,0.25 10 false *3 2.448,3.094 2.844,3.51 0.396,0.417 10 false *4 1,0.177 1.396,0.615 0.396,0.438 10 false *a 0.375,3.031 0.813,3.76 0.438,0.729 10 false *b 2.146,2.177 2.625,2.771 0.479,0.594 10 false A 1.865,2.177 2.344,2.771 0.479,0.594 10 false B 1.24,2.177 1.719,2.771 0.479,0.594 10 false C 0.958,2.177 1.438,2.771 0.479,0.594 10 false D 2.438,4.094 2.813,4.313 0.375,0.219 10 false *4 1.271,0.552 1.667,0.99 0.396,0.438 10 false O1 1.469,1.125 1.927,1.396 0.458,0.271 10 false SVC1 2.052,1.125 2.51,1.396 0.458,0.271 10 false SIG1 2.531,1.125 2.99,1.396 0.458,0.271 10 false SGD1 0.802,3.615 1.198,4.052 0.396,0.438 10 false O4 0.823,3.979 1.281,4.25 0.458,0.271 10 false SVC 0.813,3.208 1.271,3.479 0.458,0.271 10 false SIG 2.333,3.615 2.792,3.885 0.458,0.271 10 false SGD
*1 Separate Type Front Seat Cushion Spring Assembly (Front Occupant Classification Sensor LH)
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*4 Service Wire
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly (Front Occupant Classification Sensor LH))


Using a service wire, connect terminals 1 (SVC) and 3 (SGD), and connect terminals 2 (SIG) and 3 (SGD) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O1-1 (SVC1) - O1-5 (SGD1) Always Below 1 Ω
O1-3 (SIG1) - O1-5 (SGD1) Always Below 1 Ω



c.

Disconnect the service wire from connector C.



OK

4.CHECK FRONT SEAT WIRE RH (SHORT)

NG

REPLACE FRONT SEAT WIRE RH

4.CHECK FRONT SEAT WIRE RH (SHORT)
a.
C379008C05
0.958,2.344 1.271,2.573 0.313,0.229 1.542,0.885 1.542,0.302 1.542,0.302 1.375,0.302 false 1.406,2.885 1.76,2.469 false 2.583,2.885 2.198,2.469 false 1.979,2.885 1.979,2.469 false 0.615,0.875 1.146,1.604 0.531,0.729 10 false *1 2.417,0.74 2.885,1.271 0.469,0.531 10 false *2 1.229,0.229 1.688,0.656 0.458,0.427 10 false *3 1.031,2.375 1.594,2.948 0.563,0.573 10 false O1 2.104,0.875 2.573,1.406 0.469,0.531 10 false A 1.813,0.875 2.281,1.406 0.469,0.531 10 false B 1.198,0.875 1.667,1.406 0.469,0.531 10 false C 0.917,0.875 1.385,1.406 0.469,0.531 10 false D 0.708,1.896 1.271,2.469 0.563,0.573 10 false *a 1.219,2.896 1.771,3.198 0.552,0.302 10 false SVC1 1.844,2.896 2.396,3.198 0.552,0.302 10 false SIG1 2.417,2.896 2.969,3.198 0.552,0.302 10 false SGD1
*1 Separate Type Front Seat Cushion Spring Assembly (Front Occupant Classification Sensor LH)
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O1-1 (SVC1) - O1-5 (SGD1) Always 1 MΩ or higher
O1-3 (SIG1) - O1-5 (SGD1) Always 1 MΩ or higher
O1-1 (SVC1) - O1-3 (SIG1) Always 1 MΩ or higher




OK

5.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND)

NG

REPLACE FRONT SEAT WIRE RH

5.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND)
a.
C379008C05
0.958,2.344 1.271,2.573 0.313,0.229 1.542,0.885 1.542,0.302 1.542,0.302 1.375,0.302 false 1.406,2.885 1.76,2.469 false 2.583,2.885 2.198,2.469 false 1.979,2.885 1.979,2.469 false 0.615,0.875 1.146,1.604 0.531,0.729 10 false *1 2.417,0.74 2.885,1.271 0.469,0.531 10 false *2 1.229,0.229 1.688,0.656 0.458,0.427 10 false *3 1.031,2.375 1.594,2.948 0.563,0.573 10 false O1 2.104,0.875 2.573,1.406 0.469,0.531 10 false A 1.813,0.875 2.281,1.406 0.469,0.531 10 false B 1.198,0.875 1.667,1.406 0.469,0.531 10 false C 0.917,0.875 1.385,1.406 0.469,0.531 10 false D 0.708,1.896 1.271,2.469 0.563,0.573 10 false *a 1.219,2.896 1.771,3.198 0.552,0.302 10 false SVC1 1.844,2.896 2.396,3.198 0.552,0.302 10 false SIG1 2.417,2.896 2.969,3.198 0.552,0.302 10 false SGD1
*1 Separate Type Front Seat Cushion Spring Assembly (Front Occupant Classification Sensor LH)
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O1-1 (SVC1) - Body ground Always 1 MΩ or higher
O1-3 (SIG1) - Body ground Always 1 MΩ or higher
O1-5 (SGD1) - Body ground Always 1 MΩ or higher




OK

6.CHECK DTC

NG

REPLACE FRONT SEAT WIRE RH

6.CHECK DTC
a.

Connect the connectors to the occupant detection ECU and separate type front seat cushion spring assembly (front occupant classification sensor LH).


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in the occupant detection ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).


d.

Clear the DTCs stored in the airbag sensor assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).


e.

Turn the power switch off.


f.

Turn the power switch on (IG).


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1780 is not output.


HINT:

Codes other than DTC B1780 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.



OK

NG

7.CHECK OCCUPANT DETECTION ECU
7.CHECK OCCUPANT DETECTION ECU
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Replace the occupant detection ECU with a known good one (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU(w/ Occupant Classification System)>REMOVAL).

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in the occupant detection ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).


e.

Clear the DTCs stored in the airbag sensor assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).


f.

Turn the power switch off.


g.

Turn the power switch on (IG).


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1780 is not output.


HINT:

Codes other than DTC B1780 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Return the occupant detection ECU that was installed for testing to its original location (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU(w/ Occupant Classification System)>REMOVAL).



OK

8.REPLACE OCCUPANT DETECTION ECU

NG

10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY
8.REPLACE OCCUPANT DETECTION ECU
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.



c.

Connect the cable to the negative (-) auxiliary battery terminal.



NEXT

9.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
9.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
a.

Using the GTS, perform Zero Point Calibration and Sensitivity Check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

END

10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Replace the separate type front seat cushion spring assembly (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (w/ Removable Headrest)>REMOVAL).


c.

Connect the cable to the negative (-) auxiliary battery terminal.



NEXT

11.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
11.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
a.

Using the GTS, perform Zero Point Calibration and Sensitivity Check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

END

12.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Replace the separate type front seat cushion spring assembly (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (w/ Removable Headrest)>REMOVAL).

NOTICE:

Replace the front seat wire RH at the same time.


HINT:

When a short to B+ occurs in the front seat wire RH, the front occupant classification sensor LH will be damaged. Therefore, replace the front seat wire RH and the separate type front seat cushion spring assembly, which includes the front occupant classification sensor LH.



c.

Connect the cable to the negative (-) auxiliary battery terminal.



NEXT

13.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
13.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
a.

Using the GTS, perform Zero Point Calibration and Sensitivity Check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

END