Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR › from 2017.06
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278132 COMPRESSOR A

HEATING / AIR CONDITIONING  COMPRESSOR  INSTALLATION  


PROCEDURE

Hide 1.INSPECT COMPRESSOR OIL

a.
E234976

When replacing the compressor with motor assembly with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor with motor assembly before installation.

Standard:

(Oil capacity inside the new compressor with motor assembly: 115 to 130 cc (3.9 to 4.4 fl. oz.)) - (Remaining oil amount in the removed compressor with motor assembly) = (Oil amount to be removed from the new compressor)


NOTICE:
·

When checking the compressor oil level, observe the precautions on the cooler removal/installation.

·

If a new compressor with motor assembly is installed without removing some oil, there will be too much oil in the system due to the oil remaining in the pipes of the vehicle. Excessive oil in the system prevents heat exchange in the refrigeration cycle and causes ineffective cooling.

·

If the amount of oil remaining in the old compressor with motor assembly is too small, check the air conditioning system for oil leaks.

·

Be sure to use ND-OIL 11 or equivalent compressor oil. If any compressor oil other than ND-OIL 11 is used, compressor with motor assembly insulation performance may decrease, resulting in a leak of electric power.




Hide 88370 2.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY

a.
E234975E01
1.907,1.853 2.140,2.039 0.233,0.186 10 (1) 1.196,1.853 1.429,2.039 0.233,0.186 10 (2) 0.651,0.958 0.884,1.144 0.233,0.186 10 (3)

Install the compressor with motor assembly with the 3 bolts.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


b.
E234972E03
1.656,0.229 1.417,0.521 false 1.708,0.167 2,0.417 0.292,0.25 10 false *1 0.979,1.635 1.302,1.854 0.323,0.219 10 false <B> 2.521,2.729 2.844,2.948 0.323,0.219 10 false <A>

Connect the connector <B>.

Text in Illustration
*1 Green-colored Lock


c.

Connect the connector <A> and slide the green-colored lock in the direction indicated by the arrow in the illustration to lock it securely.

CAUTION:

Make sure to wear insulating gloves.


NOTICE:

Make sure that the connector is connected securely.



Hide 88704 3.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.

Compressor oil:

ND-OIL 11 or equivalent



c.

Install the O-ring onto the suction hose sub-assembly.


d.

Install the suction hose sub-assembly to the compressor with motor assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.

Remove the vinyl tape from the hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.

Compressor oil:

ND-OIL 11 or equivalent



c.

Install the O-ring onto the No. 1 cooler refrigerant discharge hose.


d.

Install the No. 1 cooler refrigerant discharge hose to the compressor with motor assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 51441C 5.INSTALL ENGINE UNDER COVER RH (Separated Cover Type)

Hide 6.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY (Integrated Cover Type)

Hide 8.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT