Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2017.06
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278196 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Low Beam Headlight Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the low beam headlights.

WIRING DIAGRAM

for Halogen Headlight


E366907E08
3.917,0.76 4.229,0.958 0.313,0.198 10 false 3C 0.073,0.729 0.948,1.469 0.875,0.74 10 false from Auxiliary Battery 1.406,0.885 2.323,1.083 0.917,0.198 10 false H-LP MAIN 2.938,1.25 3.854,1.448 0.917,0.198 10 false H-LP 4.24,1.115 5.844,1.833 1.604,0.719 10 false Instrument Panel Junction Block Assembly 5.99,0.729 6.49,0.948 0.5,0.219 10 false HRLY 5.219,2.594 6.865,3.313 1.646,0.719 10 false Main Body ECU (Multiplex Network Body ECU) 2.75,2.573 3.667,2.771 0.917,0.198 10 false H-LP LH-LO 0.979,3.042 1.896,3.24 0.917,0.198 10 false A76 1.281,2.708 2.198,2.906 0.917,0.198 10 false Low Beam 0.979,3.188 2.635,3.49 1.656,0.302 10 false Headlight Assembly LH 0.969,5.01 1.885,5.208 0.917,0.198 10 false A75 0.969,5.146 2.958,5.385 1.99,0.24 10 false Headlight Assembly RH 2.74,4.573 3.656,4.771 0.917,0.198 10 false H-LP RH-LO 0.844,2.344 1.177,2.563 0.333,0.219 10 false 2 1.031,2.344 1.365,2.563 0.333,0.219 10 false E 1.969,2.344 2.302,2.563 0.333,0.219 10 false LO 2.26,2.313 2.594,2.531 0.333,0.219 10 false 3 2.594,0.656 2.927,0.875 0.333,0.219 10 false 1 2.604,0.896 2.938,1.115 0.333,0.219 10 false 5 3.479,0.656 3.813,0.875 0.333,0.219 10 false 2 3.479,0.906 3.813,1.125 0.333,0.219 10 false 3 3.927,0.552 4.26,0.771 0.333,0.219 10 false 18 5.74,0.656 6.073,0.875 0.333,0.219 10 false 15 5.219,2.427 5.583,2.74 0.365,0.313 10 false MB 1.021,4.313 1.354,4.531 0.333,0.219 10 false E 1.979,4.333 2.313,4.552 0.333,0.219 10 false LO 0.833,4.323 1.167,4.542 0.333,0.219 10 false 2 2.271,4.313 2.604,4.531 0.333,0.219 10 false 3 1.281,4.677 2.198,4.875 0.917,0.198 10 false Low Beam


for LED Headlight


E333940E11
0.177,0.844 1.917,1.135 1.74,0.292 10 false from Auxiliary Battery 2.042,1.01 2.958,1.208 0.917,0.198 10 false H-LP MAIN 3.427,1.375 4.344,1.573 0.917,0.198 10 false H-LP 4.396,1.229 6,2.021 1.604,0.792 10 false Instrument Panel Junction Block Assembly 6.146,0.844 7.063,1.042 0.917,0.198 10 false HRLY 5.896,0.76 6.438,0.958 0.542,0.198 10 false 15 4.458,0.854 5,1.052 0.542,0.198 10 false 3C 4.469,0.667 5.01,0.865 0.542,0.198 10 false 18 3.104,0.74 3.646,0.938 0.542,0.198 10 false 1 3.104,0.979 3.646,1.177 0.542,0.198 10 false 5 3.938,0.74 4.479,0.938 0.542,0.198 10 false 2 3.938,0.979 4.479,1.177 0.542,0.198 10 false 3 0.323,2.802 0.865,3 0.542,0.198 10 false 2 0.521,2.802 1.063,3 0.542,0.198 10 false E 2.833,2.781 3.375,2.979 0.542,0.198 10 false LO 3.146,2.771 3.688,2.969 0.542,0.198 10 false 4 0.313,5.323 0.854,5.521 0.542,0.198 10 false 2 0.51,5.323 1.052,5.521 0.542,0.198 10 false E 2.854,5.302 3.396,5.5 0.542,0.198 10 false LO 3.167,5.302 3.708,5.5 0.542,0.198 10 false 4 1.469,2.115 2.385,2.313 0.917,0.198 10 false Low Beam 1.198,2.771 2.74,3.115 1.542,0.344 10 false Light Control ECU 1.083,3.76 3.208,4.063 2.125,0.302 10 false Headlight Assembly LH 1.083,3.604 1.625,3.802 0.542,0.198 10 false A69 1.458,4.635 2.375,4.833 0.917,0.198 10 false Low Beam 1.229,5.344 3.063,5.635 1.833,0.292 10 false Light Control ECU 1.094,6.271 3.469,6.531 2.375,0.26 10 false Headlight Assembly RH 1.094,6.115 1.635,6.313 0.542,0.198 10 false A68 3.292,5.573 4.323,5.792 1.031,0.219 10 false H-LP RH-LO 3.281,3.031 4.198,3.229 0.917,0.198 10 false H-LP LH-LO 5.438,5.573 7.083,6.302 1.646,0.729 10 false Main Body ECU (Multiplex Network Body ECU) 5.448,5.406 5.99,5.604 0.542,0.198 10 false MB


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Headlight Relay Low beam headlights OFF or ON -

OK:

Low beam headlights illuminate.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT H-LP RELAY
2.INSPECT H-LP RELAY

OK

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - H-LP RELAY)

NG

REPLACE H-LP RELAY

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - H-LP RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (H-LP relay) - Body ground Power switch off 11 to 14 V
5 (H-LP relay) - Body ground Power switch off 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY)
a.

for Halogen Headlight:

i.

Disconnect the A76 headlight assembly LH connector.


ii.

Disconnect the A75 headlight assembly RH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (H-LP relay) - A76-3 (LO) Always Below 1 Ω
3 (H-LP relay) - A75-3 (LO) Always Below 1 Ω
3 (H-LP relay) or A76-3 (LO) - Body ground Always 10 kΩ or higher
3 (H-LP relay) or A75-3 (LO) - Body ground Always 10 kΩ or higher




b.

for LED Headlight:

i.

Disconnect the A69 headlight assembly LH connector.


ii.

Disconnect the A68 headlight assembly RH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (H-LP relay) - A69-4 (LO) Always Below 1 Ω
3 (H-LP relay) - A68-4 (LO) Always Below 1 Ω
3 (H-LP relay) or A69-4 (LO) - Body ground Always 10 kΩ or higher
3 (H-LP relay) or A68-4 (LO) - Body ground Always 10 kΩ or higher





OK

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (H-LP relay) - 3C-18 Always Below 1 Ω
2 (H-LP relay) or 3C-18 - Body ground Always 10 kΩ or higher




OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E173038C41
1.26,0.313 1.615,0.531 0.354,0.219 4.625,0.313 4.979,0.531 0.354,0.219 4.604,1.083 4.875,1.521 false 0.146,0.104 0.51,0.406 0.365,0.302 10 false *a 4.917,1.51 5.365,1.677 0.448,0.167 10 false HRLY 1.365,0.354 1.677,0.552 0.313,0.198 10 false 3C 4.729,0.354 5.083,0.573 0.354,0.219 10 false MB
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-18 - MB-15 (HRLY) Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY